Microstructure and mechanical properties of casting Al-3Li-2Mg-1Zn-0.1Zr alloys modified by Sc additions
Source abstract
Abstract
Abstract In the present study, microstructure and mechanical properties of casting Al-3Li-2Mg-1Zn-0.1Zr alloys modified by Sc additions have been investigated. As-aged Al-3Li-2Mg-1Zn-0.2Sc-0.1Zr alloy possesses a desirable comprehensive mechanical performance. The YS, UTS and El reach 253 MPa, 406 MPa and 7.4% respectively. With the addition of Sc, a more than 50% reduction in the grain size was achieved by the promoted heterogeneous nucleation on primary Al3(Sc, Zr) phases and the grain growth resistance was enhanced by the Zener pinning. After the heat treatment, core-shell composite particles precipitated from the matrix. The shell consists entirely of Al3Li phases. In contrast, both Al3(Sc, Zr) and Al3Sc cores can be observed in the Sc-containing alloys. Increasing the Sc content from 0.1 wt% to 0.2 wt%, the mean radius of cores increases, while the mean width of shells and the number density of particles seem not to be affected. With the passage of ageing time, the coarsening of composite particles occurred, though the dimension of the core remained almost constant. The kinetics follows the KV model and the exponent (n−1) is about 0.11, which is lower than the expected value (0.33) probably due to the unreached quasi-steady-state at the present low temperature.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. Review on failure behaviors of fusion welded high-strength Al alloys due to fine equiaxed zone10.1016/j.engfracmech.2019.01.013 ↗
2. Recent advances in ageing of 7xxx series aluminum alloys: a physical metallurgy perspective10.1016/j.jallcom.2018.11.286 ↗
3. Aluminium alloys as structural material: a review of research10.1016/j.engstruct.2020.111372 ↗
4. Is lithium the new gold?10.1038/nchem.680 ↗
5. Analysis of microstructure and high-temperature tensile properties of 2060 Al-Li alloy strengthened by laser shock peening10.1016/j.jallcom.2020.158539 ↗
6. Effects of coarse Al2CuLi phase on the hot deformation behavior of Al–Li alloy10.1016/j.jallcom.2019.152469 ↗
7. Influences of Mn content on the microstructures and mechanical properties of cast Al-3Li-2Cu-0.2Zr alloy10.1016/j.jallcom.2017.05.030 ↗
8. Significant roles of minor Mg addition in microstructural evolution and mechanical properties of cast Al–3Li–2Cu-0.15Zr alloy
9. Strengthening mechanisms, deformation behavior, and anisotropic mechanical properties of Al-Li alloys: a review10.1016/j.jare.2017.12.004 ↗
10. Effects of pre-strain and stress level on stress relaxation ageing behaviour of 2195 Al–Li alloy: experimental and constitutive modelling10.1016/j.jallcom.2020.156829 ↗
11. Evolution of microstructure and texture in the third generation Al–Li alloy AA2195 during warm hybrid processing10.1016/j.jallcom.2020.156750 ↗
12. Size effect in the Al3Sc dispersoid-mediated precipitation and mechanical/electrical properties of Al-Mg-Si-Sc alloys10.1016/j.jmst.2020.03.056 ↗
13. Effects of Mg and Sc additions on the microstructure, mechanical properties, and thermal stability of a cast Al-2Li-2Cu-0.2Zr alloy after thermal exposure10.1016/j.jallcom.2019.02.062 ↗
14. Grain refinement mechanism in an Al–Si–Mg alloy with scandium10.1016/j.jallcom.2012.07.018 ↗
15. Dendritic and seaweed growth of proeutectic scandium tri-aluminide in hypereutectic Al-Sc undercooled melt10.1016/j.actamat.2020.08.078 ↗
16. Coarsening of Al3Sc precipitates in Al-Mg-Sc alloys10.1016/j.jallcom.2018.12.133 ↗
17. Simultaneous improvement in corrosion resistance and hardness of a model 2xxx series Al-Cu alloy with the microstructural variation caused by Sc and Zr additions10.1016/j.corsci.2019.108095 ↗
18. Microstructure evolution of the 1469 Al–Cu–Li–Sc alloy during homogenization10.1016/j.jallcom.2014.06.033 ↗
19. ScAl3 Crystal Structure: Datasheet from "PAULING FILE Multinaries Edition – 2012", in: P. Villars, K. Cenzual (Eds.), Springer Materials. Springer-Verlag Berlin Heidelberg & Material Phases Data System (MPDS), Switzerland & National Institute for Materials Science (NIMS), Japan. https://materials.springer.com/isp/crystallographic/docs/sd_0260376.
20. Al Crystal Structure: Datasheet from "PAULING FILE Multinaries Edition – 2012", in: P. Villars, K. Cenzual (Eds.) SpringerMaterials, Springer-Verlag Berlin Heidelberg & Material Phases Data System (MPDS), Switzerland & National Institute for Materials Science (NIMS), Japan. https://materials.springer.com/isp/crystallographic/docs/sd_0251015.
21. Quantitative phase analysis of Al-Mg-Li and Al-Cu-Li alloys10.4028/www.scientific.net/MSF.794-796.915 ↗
22. Precipitation characteristics and morphological transitions of Al3Sc precipitates10.1016/j.jallcom.2019.03.256 ↗
23. The use of thermal hydrogen decrepitation to recycle Nd-Fe-B magnets from electronic waste10.2298/JMMB200207032P ↗
24. Al–5.5Mg–1.5Li–0.5Zn–0.07Sc–0.07Zr alloy produced by gravity casting and heat treatment processing10.1080/10426914.2017.1401725 ↗
25. The effect of cooling rate on the morphology of primary Al3Sc intermetallic particles in Al–Sc alloys10.1016/S1359-6454(01)00050-7 ↗
26. Effects of cold predeformation on dissolution of second-phase Al2Cu particles during solution treatment of 2219 Al-Cu alloy forgings10.1016/j.matchar.2017.10.026 ↗
27. Thermal stability of Al3(Scx,Zr1−x)-dispersoids in extruded aluminium alloys10.1016/j.msea.2007.04.054 ↗
28. Grain growth in a nanocrystalline Al-Sc alloy10.2320/matertrans.45.2264 ↗
29. Influence of Sc content on the microstructure and mechanical properties of cast Al-2Li-2Cu-0.5Mg-0.2Zr alloy10.1016/j.matchar.2018.05.046 ↗
30. Coarsening kinetics and strengthening mechanisms of core-shell nanoscale precipitates in Al-Li-Yb-Er-Sc-Zr alloy10.1016/j.jmst.2020.05.061 ↗
31. First-principles study of the nucleation and stability of ordered precipitates in ternary Al–Sc–Li alloys10.1016/j.actamat.2011.01.041 ↗
32. Atomic structure of core-shell precipitates in Al-Li-Sc-Zr alloys studied by analytical and aberration-corrected TEM/STEM10.1017/S1431927608084808 ↗
33. Microstructures and mechanical properties of ultralight cast Al-3Li-XMg-0.1Zr alloys10.1016/j.matchar.2020.110698 ↗
34. The kinetics of precipitation from supersaturated solid solutions10.1016/0022-3697(61)90054-3 ↗
35. Coarsening kinetics of nanoscale Al3Sc precipitates in an Al–Mg–Sc alloy10.1016/j.actamat.2005.05.025 ↗
36. Impurity diffusion in aluminum10.1016/0022-3115(78)90275-1 ↗
37. Coarsening of δ′(Al 3 Li) and composite precipitates in an Al-2.5% Li-0.15% Zr alloy10.1007/BF00356567 ↗
38. Ostwald ripening in ternary alloys10.1007/BF02649761 ↗