journal article·2021-12

Microstructural properties, thermodynamics and kinetics of Al-Si semi-solid billet fabricated by liquid phase reaction sintering

Wenchao Liu, Lianxi Hu, Yu Sun, Jianbo Jia, Jingyuan Shen, Shangqing Sun, Jufu Jiang

Publisher page

Abstract

Abstract This study proposes a method of preparing an Al-Si semi-solid billet by cold pressing and liquid phase reaction sintering with Al and Si elemental powders. The microstructural evolution and tensile properties of the billets were evaluated. Thermodynamic and kinetic analyses of the reaction were also conducted. The kinetic equation for the accurate prediction of the liquid phase content was derived. Al and Si elemental powders were reacted at 585 °C, 595 °C and 605 °C to form a liquid phase and were uniformly distributed in the billet. After reaction sintering, semi-solid billets with equiaxed Al particles that were uniformly distributed in the liquid phase were formed. Increases in Si content and reaction temperature contributed to the increase in liquid phase content after thermodynamic equilibrium. An increase in temperature and a decreased in porosity promoted the kinetic formation of the liquid phase. Meanwhile, the kinetic equations y6 wt% = 86.61·exp(−25487.4/RT)·t0.35 and y8 wt% = 95.5·exp(−36154.2/RT)·t0.4 described the relationship between the liquid phase formation ratio and the reaction temperature and time while accurately predicting the liquid phase content during the reaction. The increase in liquid phase content in the microstructure improved the strength of the billet but reduced its elongation. Moreover, the fracture mode of the billet changed from a ductile fracture to a brittle fracture. The billet fracture was mainly attributed to the generation and propagation of cracks in the liquid phase.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. Interflake spacings and undercoolings in Al-Si irregular eutectic alloy10.1016/j.msea.2003.11.020 ↗
2. Electrical resistivity of Cd-Sn, Bi-Cd, Al-Si eutectics, Al-3wt%Si hypoeutectic depending on the temperature10.1361/105994906X124578 ↗
3. Dendritic growth in an aluminum-silicon alloy10.1007/s11665-006-9002-2 ↗
4. An investigation on semi-solid Al-7Si-0.3Mg alloy produced by mechanical stirring10.1016/j.jmatprotec.2005.04.071 ↗
5. Semi-solid near-net shape rheocasting of heat treatable wrought aluminum alloys10.1016/S1003-6326(09)60364-2 ↗
6. Microstructural evolution of an ECAE-formed ZK60-RE magnesium alloy in the semi-solid state10.1016/j.msea.2008.12.042 ↗
7. Application of electromagnetic stirring for the homogenization of aluminium billet cast in a semi-continuous machine10.1016/j.jmatprotec.2009.09.016 ↗
8. Preparation and rheocasting of semisolid slurry of 5083 Al alloy with indirect ultrasonic vibration process10.1016/j.msea.2011.08.014 ↗
9. Studies on rheocasting using cooling slope
10. An investigation on the microstructural evolution and mechanical properties of A380 aluminum alloy during SIMA process10.1016/j.jallcom.2011.07.068 ↗
11. Review: liquid phase sintering10.1007/s10853-008-3008-0 ↗
12. Liquid phase sintering of the commercial 2xxx series Al blended powder10.1016/j.jallcom.2005.09.070 ↗
13. The initial stage of liquid phase sintering for an Al-14Si-2.5Cu-0.5Mg (wt%) P/M alloy10.1016/j.msea.2010.02.078 ↗
14. Liquid-phase sintering of powder bodies of the Al-Si system, Russian10.3103/S1067821211010214 ↗
15. Effect of microwave and conventional heating on sintering behavior and properties of Al-Mg-Si-Cu alloy10.1016/j.matchemphys.2011.07.008 ↗
16. Impact of the structure on mechanical and tribological properties of sintered (Al-12 Si)-40 Sn Alloy10.1134/S2075113318050246 ↗
17. The influence of interfacial structure on the mechanical properties of liquid-phase-sintered aluminum-ceramic composites10.1016/0921-5093(90)90345-4 ↗
18. Crack healing in liquid-phase-pressureless-sintered silicon carbide-aluminum nitride composites10.1016/j.jeurceramsoc.2009.08.002 ↗
19. Liquid-phase sintering of nanodiamond composite coatings on aluminum A319 using a focused laser beam10.1016/j.surfcoat.2009.06.025 ↗
20. Microstructure and properties of in situ fabricated Al-5wt%Si-Al2O3 composites
21. Effects of oxide addition on the microstructure and mechanical properties of lamellar SiC scaffolds and Al-Si-Mg/SiC composites prepared by freeze casting and pressureless infiltration10.1016/j.ceramint.2016.03.052 ↗
22. Microstructure of silicon nitride ceramics sintered with rare-earth oxides10.1016/0956-7151(94)00298-V ↗
23. Densification during sintering in the presence of a liquid phase. I. Theory10.1063/1.1735156 ↗
24. The effect of tin and nitrogen on liquid phase sintering of Al-Cu-Mg-Si alloys10.1016/j.actamat.2008.01.047 ↗
25. The crystal growth of silicon in Al-Si alloys10.1007/BF01112278 ↗
26. The Al-Si phase diagram10.1017/S1431927609092642 ↗
27. Estimation of the shifting distance of the eutectic point in hypereutectic Al-Si alloys by the lever rule10.1016/j.scriptamat.2006.11.023 ↗
28. Modelling of iron dissolution during hot dip galvanizing of strip steel10.1179/026708304225011289 ↗
29. Brandes · 1983
30. Microstructure evolution and mechanical properties of Al-8wt%Si semi-solid billet fabricated by powder metallurgy liquid phase reaction sintering10.1016/j.msea.2020.140656 ↗
31. What is the process window for semi-solid processing10.1007/s11661-015-3185-9 ↗
32. Solid–liquid diffusion controlled rate equations10.1016/S0040-6031(99)00256-7 ↗
33. Microstructural evolution of AZ61–10 at%Ti composite powders during mechanical milling10.1016/j.matdes.2016.05.014 ↗
34. Microstructural evolution, creep, and tensile behavior of a Ti-22Al-25Nb (at%) orthorhombic alloy10.1016/j.msea.2014.02.004 ↗
35. On the fracture toughness of advanced materials10.1002/adma.200803322 ↗