journal article·2021-05

Investigation of elastic modulus and morphology of reinforcement phase on the stress distribution of copper matrix composites

Xianlong Wang, Jinchuan Jie, Shichao Liu, Yangyang Zhang, Tingju Li

Publisher page

Abstract

Abstract In the present work, the models of composite reinforced by sphere, rod and short fiber with different elastic modulus were established, and the effects of morphology and elastic modulus of reinforcement on mechanical properties were investigated by the finite element analysis. The phase stress partition parameters and stress gradient are used to evaluate the load-transfer efficiency between the reinforcement and matrix. The results revealed that the yield strength increases firstly and then stables with the increase in the elastic modulus of reinforcement. Furthermore, the reinforcements with a larger aspect ratio can induce higher stress gradient and load-transfer efficiency, thereby leading to the increase of yield strength. The effect of the aspect ratio on the yield strength follows the calculation of shear-lag model. Additionally, the aspect ratio and elastic modulus have a synergistic effect on yield strength. The higher aspect ratio reinforcements will make the yield strength of the composite increase significantly with the increasing elastic modulus of the reinforcement. It is anticipated that the present study would provide guidance for the design and underlying performance prediction of metal matrix composites.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. Deformation mechanism and enhanced properties of Cu–TiB2 composites evaluated by the in-situ tensile test and microstructure characterization10.1016/j.jallcom.2020.156555 ↗
2. On the presence of work-hardened zones around fibers in a short-fiber-reinforced Al metal matrix composite10.1016/j.actamat.2012.07.042 ↗
3. Microstructure and ablation behaviour of a carbon/carbon-ZrC-Cu composite prepared by adding Ti to Zr/Cu powder mixture10.1016/j.corsci.2019.108175 ↗
4. Nickel/Nickel phosphide composite embedded in N-doped carbon with tunable electromagnetic properties toward high-efficiency microwave absorption10.1016/j.compositesa.2020.106141 ↗
5. Effects of Cr3C2 content and temperature on sliding friction and wear behaviors of Cr3C2/Ni3Al composite materials10.1016/j.wear.2018.08.013 ↗
6. Effect of reinforcement shape on fracture behaviour of SiC/Al composites with network architecture10.1016/j.compstruct.2019.02.067 ↗
7. Relationship between microstructure, properties and reaction conditions for Cu–TiB2 alloys prepared by in situ reaction10.1016/j.actamat.2009.06.030 ↗
8. The effect of modified interfaces on the mechanical property of β-silicon nitride whiskers reinforced Cu matrix composites10.1016/j.jallcom.2014.07.060 ↗
9. Cyclic plastic behavior of unidirectional SiC fibre-reinforced copper composites under uniaxial loads: an experimental and computational study10.1016/j.compstruct.2018.06.012 ↗
10. Pure Al matrix composites produced by vacuum hot pressing: tensile properties and strengthening mechanisms10.1016/j.msea.2004.05.081 ↗
11. Comparison between current models for the strength of particulate-reinforced metal matrix nanocomposites with emphasis on consideration of Hall–Petch effect10.1016/j.msea.2011.10.043 ↗
12. Effect of micromechanical models on structural responses of functionally graded plates10.1016/j.compstruct.2014.09.031 ↗
13. Two-scale TiB/Ti64 composite coating fabricated by two-step process10.1016/j.jallcom.2018.05.002 ↗
14. Effect of aspect ratios of in situ formed TiB whiskers on the mechanical properties of TiBw/Ti–6Al–4V composites10.1016/j.scriptamat.2011.12.024 ↗
15. Experimental and numerical investigation on strengthening mechanisms of nanostructured Al-SiC composites10.1016/j.jallcom.2018.10.007 ↗
16. Multiscale modeling of macroscopic and microscopic residual stresses in metal matrix composites using 3D realistic digital microstructure models10.1016/j.compstruct.2015.10.045 ↗
17. FEM predictions of damage in continous fiber ceramic matrix composites under transverse tension using the crack band method10.1016/j.actamat.2015.09.002 ↗
18. Experimental and numerical studies of the effect of particle size on the deformation behavior of the metal matrix composites10.1016/j.msea.2006.10.158 ↗
19. Synthesis and characterization of in-situ (Al–Al3Ti–Al2O3)/Al dual matrix composite10.1016/j.jallcom.2020.155745 ↗
20. Enhancing compressive response of AZ31B magnesium alloy using alumina nanoparticulates10.1016/j.compscitech.2008.04.020 ↗
21. Size dependent strengthening in particle reinforced aluminium10.1016/S1359-6454(01)00327-5 ↗
22. Strengthening and fracture behaviors in SiCp/Al composites with network particle distribution architecture10.1016/j.msea.2018.10.105 ↗
23. Study on stress distribution in microregion close to the shell of core-shell particle reinforced metal matrix composites10.1016/j.msea.2020.139317 ↗
24. An enhanced finite element model considering multi strengthening and damage mechanisms in particle reinforced metal matrix composites10.1016/j.compstruct.2019.111281 ↗
25. Effects of degree of deformation on the microstructure, mechanical properties and texture of hybrid-reinforced titanium matrix composites10.1016/j.actamat.2012.01.032 ↗
26. Prediction of the thermomechanical behavior of particle-reinforced metal matrix composites10.1016/j.compositesb.2012.09.056 ↗
27. Multiscale micromechanical modeling of polymer/clay nanocomposites and the effective clay particle10.1016/j.polymer.2003.10.100 ↗
28. The elasticity and strength of paper and other fibrous materials10.1088/0508-3443/3/3/302 ↗
29. A probabilistic theory of the strength of short-fibre composites with variable fibre length and orientation10.1007/BF00543519 ↗