journal article·2020-08

Quasi-gradient variation of microstructures and properties of Cu–Sn alloy along the thickness direction under cold spinning

Jun Hui, Wenguan Liu, Biao Wang

Publisher page

Abstract

Abstract During cold spinning, the grain size, grain boundary angle and tensile strength of Cu– Sn alloy show quasi gradient changes in the thickness direction (TD) of hollow cylinder. According to a mechanical analysis, electron backscattering diffraction observations (EBSD), and a finite element simulation, the grain size of Cu–Sn alloy after spinning increases from the outer surface to the inner surface. The number of ultrafine grains was largest on the outer surface, and the original grain boundaries were retained on the inner surface. All of the grain orientations from the outer surface to the inner surface were randomly distributed. An analysis of the grain misorientation suggested that low-angle grain boundaries (LAGBs; 10°) was inversely proportional to that of LAGBs, the grain boundary energy (GBE) of the HAGBs decreased with increasing number of LAGBs, and the number of HAGBs also decreased gradually. According to tensile tests at room temperature, the outer surface exhibited the highest ultimate tensile strength and the inner surface exhibited the greatest plasticity.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. On the manufacturing of a gas turbine engine Part Through metal spinning process
2. A review of the mechanics of metal spinning10.1016/j.jmatprotec.2009.08.021 ↗
3. Flow forming of tubes-a review
4. End forming of thin-walled tubes10.1016/j.jmatprotec.2006.04.040 ↗
5. External inversion of thin-walled tubes using a die: experimental and theoretical investigation10.1016/S0890-6955(03)00062-2 ↗
6. Experimental study of thickness reduction effects on mechanical properties and spinning accuracy of aluminium 7075-O, during flow forming10.1007/s00170-010-2782-4 ↗
7. Investigation of effective parameters on surface roughness in thermomechanical tube spinning process10.1007/s12289-009-0420-1 ↗
8. Umerical modelling, validation and analysis of multi-pass sheet metal spinning processes10.1007/s12289-016-1308-5 ↗
9. Flow stress evaluation in hot rolling of steel10.1007/s11665-014-1049-x ↗
10. Hot spinning process of cylindrical workpieces of TA15 titanium alloy
11. Effect of spinning deformation on microstructure evolution and mechanical property of TA15 titanium alloy
12. Numerial simulation and experimental study on multi-pass stagger spinning of internally toothed gear using plate blank10.1016/j.jmatprotec.2015.10.001 ↗
13. Influence of roller distribution modes on spinning force during tube spinning10.1016/j.ijmecsci.2016.04.009 ↗
14. Fabrication of curved generatrix workpiece of TA15 titanium alloy by variable thickness tube spinning and flaring process10.1007/s00170-016-8917-5 ↗
15. An experimental analysis of a flaring process for tube ends using a novel spinning tool10.1007/s00170-017-0106-7 ↗
16. Statistical analysis of dimensional changes in thermomechanical tube-spinning process10.1007/s00170-010-2780-6 ↗
17. Numerical simulation of single and dual pass conventional spinning processes10.1007/s12289-009-0602-x ↗
18. Compression spinning of circular magnesium tube using heated roller tool10.1016/j.jmatprotec.2005.02.199 ↗
19. Influence of ultrasonic vibrations on tube spinning process10.1016/j.jmatprotec.2012.02.006 ↗
20. Influence of roller distribution modes on spinning force during tube spinning10.1016/j.ijmecsci.2016.04.009 ↗
21. Review on hot spinning for difficult-to-deform lightweight metals10.1016/S1003-6326(15)63778-5 ↗
22. Springback mechanism and compensation of cryogenic Ti alloy tube after numerically controlled bending10.1016/S1003-6326(12)61721-X ↗
23. The influence of power spinning and annealing temperature on microstructures and properties of Cu-Sn alloy10.1016/j.matchar.2018.08.015 ↗
24. Chen · 1986
25. Microstructural evolution analysis of grains and tensile properties of tin bronze in hot extrusion at different temperatures10.1080/09603409.2018.1457603 ↗
26. Enhanced finite element analysis of material deformation and strain distribution in spinning of 42CrMo steel tubes at elevated temperature10.1016/j.matdes.2012.11.049 ↗
27. Experimental and numerical analysis of helical-wedge rolling process for producing steel balls10.1016/j.ijmachtools.2012.12.006 ↗
28. 3D coupled macro–microscopic finite element modelling and simulation for combined blank-forging and rolling process of alloy steel large ring10.1016/j.commatsci.2012.12.035 ↗
29. Dislocation–twin interactions in nanocrystalline fcc metals10.1016/j.actamat.2010.10.028 ↗
30. Mechanical behavior of nanocrystalline metals and alloys10.1016/j.actamat.2003.08.032 ↗
31. Deformation twinning in nanocrystalline materials10.1016/j.pmatsci.2011.05.001 ↗
32. Ultrahigh strength and high electrical conductivity in copper10.1126/science.1092905 ↗
33. Strain-induced ultrahard and ultrastable nanolaminated structure in nickel10.1126/science.1242578 ↗
34. Mechanical properties of nanocrystalline materials10.1016/j.pmatsci.2005.08.003 ↗
35. Kovacs · 1973
36. Formation mechanism of wide stacking faults in nanocrystalline Al10.1063/1.1734689 ↗
37. Mechanism of increasing spinnability by multi-pass spinning forming - analysis of damage evolution using a modified GTN model10.1016/j.ijmecsci.2019.05.030 ↗
38. Atomistic study of dislocation nucleation in Ge/(001)Si heterostructuses10.1080/01418619508239925 ↗