Effect of cross-sectional reduction ratio on microstructure evolution of semi-solid 7075 aluminum alloy prepared by RFSIMA process
Source abstract
Abstract
Semi-solid billets of 7075 aluminum alloy were fabricated by radial forging strain induced melting activation (RFSIMA) process. Effect of the cross-sectional reduction ratio on microstructure of fabricated 7075 aluminum alloys was analyzed. The results indicate that the average grain size of α-Al decreased from 109μm to 70μm as the cross-sectional reduction ratio increased from 0% to 73% during the 20-minute isothermal treatment at 620°C.The spheroidization trend of the grains became more pronounced; During the semi-solid isothermal treatment, the segregation of Cu at grain boundaries increased slowly with the increase in the cross-sectional reduction ratio. Zn and Mg exhibited uniform distribution without significant segregation at low cross-sectional reduction ratios (43% and below). When the cross-sectional reduction ratio reached 62%, slight segregation of Zn and Mg was observed at the grain boundaries. At a cross-sectional reduction ratio of 73%, the segregation of Zn and Mg at the grain boundaries reached a level similar to that of Cu. The optimal cross-sectional reduction ratio for the RFSIMA process was found to be 62%; the microstructural evolution mechanism of the semi-solid 7075 aluminum alloy prepared by the RFSIMA process was investigated.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Characterization of Al-7075 metal matrix composites: a review10.1016/j.jmrt.2017.10.012 ↗
2. Evolution of second phases and mechanical properties of 7075 Al alloy processed by solution heat treatment10.1016/S1003-6326(17)60240-1 ↗
3. An overview on the process development and the formation of non-dendritic microstructure in semi-solid processing of metallic materials10.3390/cryst12081044 ↗
4. Microstructure evolution and coarsening kinetics of semisolid CuSn10P1 alloy under short-time isothermal treatment10.1088/2053-1591/abf19f ↗
5. Modification of Mg2Si morphology in Mg–9%Al–0.7%Si alloy by the SIMA process10.1016/j.matchar.2011.01.006 ↗
6. Effect of compression ratio on microstructure evolution of Mg–10%Al–1%Zn–1%Si alloy prepared by SIMA process10.1016/S1003-6326(21)65678-9 ↗
7. Mechanical properties and micro-structural of Al-Zn-Mg-Cu alloy by semi-solid SIMA processed
8. Effect of ECAP process on liquid distribution of AZ80M alloy during semi-solid isothermal heat treatment10.1016/S1003-6326(21)65601-7 ↗
9. Thixoforming of semi-solid AZ91D alloy with high solid fraction prepared by the RUE-based SIMA process10.1007/s00170-017-0874-0 ↗
10. New insight into the radial forging process by an asymptotic-based axisymmetric analysis10.1016/j.apm.2021.10.030 ↗
11. Experimental study of mechanical properties of 30SiMn2MoVA steel gun barrel processed by cold radial forging10.1115/1.4047654 ↗
12. The microstructure, texture evolution and plasticity anisotropy of 30SiMn2MoVA high strength alloy steel tube processed by cold radial forging10.1016/j.matchar.2020.110641 ↗
13. Microstructural evolution of Mg-10Gd-3Y–1Zn-0.4Zr (wt%) alloy prepared by strain-induced melt activation process10.1016/j.matchar.2020.110831 ↗
14. Microstructure and texture characterization of 7075 Al alloy during the SIMA process10.1016/j.matchar.2015.06.013 ↗
15. Microstructural evolution and mechanical properties of 7075 aluminium alloy during semi-solid compression deformation10.3390/cryst12081119 ↗
16. Comparison of microstructural evolution of 7075 aluminum alloy fabricated by SIMA and RAP
17. Microstructural evolution of semisolid 6063 aluminum alloy prepared by recrystallization and partial melting process10.1007/s11665-017-2854-9 ↗
18. Effect of alloy composition on microstructure and tensile properties of net-shaped castings of Al–Zn–Mg–Cu alloys
19. Recrystallisation in the semi-solid state in 7075 aluminium alloy10.1016/j.msea.2008.01.057 ↗
20. Phase evolution and mechanical behavior of the semi-solid SIMA processed 7075 aluminum alloy10.3390/met6030042 ↗
21. Effects of cyclic extrusion and compression parameters on microstructure and mechanical properties of Mg–1.50Zn–0.25Gd alloy
22. strain induced melt activation (SIMA): original concept, its impact and present understanding10.1080/13640461.2020.1801561 ↗
23. Strain-induced dissolution and precipitation of secondary phases and synergetic stengthening mechanisms of Al–Zn–Mg–Cu alloy during ECAP10.1002/adem.201801182 ↗
24. Semisolid rheoforming of magnesium alloys: a review10.1016/j.matdes.2020.108990 ↗
25. Microstructural and mechanical response of ZK60 magnesium alloy subjected to radial forging10.1016/j.jmst.2020.11.080 ↗
26. Quantitative analysis of microsegregation in DC cast 7075 aluminum alloy
27. Microstructure evolution of wrought nickel based superalloy GH4037 in the semi-solid state10.1016/j.matchar.2018.04.057 ↗
28. Hot deformation behavior of high strength 7075 aluminum alloy and its microstructure evolution in radial forging for drive shaft of heavy truck