Hot temperature tribological behavior of Mg-Zn-Gd alloy under graphite surfactant functionalized SN500
Source abstract
Abstract
The effect of SN500 and SN500 +G lubricants on the wear behavior of Mg-Zn-Gd alloy was studied. For this purpose, Mg-Zn-Gd alloy was produced by the stir casting method. The wear test was performed under 20, 40, and 80 N with a velocity of 0.5 m/s for 1000 m at different temperatures (25, 100, 150, 200, and 250 °C) under SN500 and SN500 +G lubricants. The results showed that in the presence of precipitates weight loss and wear rate were reduced. With the increasing load in all samples, weight loss and wear rate increased. The lowest wear rate was obtained at 250 under 20 N and was equal to 0.036 and 0.030 m 3/m, and with an increase in the load to 80 N, it reached 0.044 and 0.042 m 3 /m for samples under SN500 and SN500 +G, respectively. It was also observed that lubrication of SN500 +G in all samples created better properties than SN500. The addition of graphite to SN500 also reduced the coefficient of friction. So that the friction coefficient of the tested sample under 80 N at 250 °C under SN500 has decreased by 15% compared to SN500 +G. The worn surfaces SEM micrographs of samples under SN500 +G lubricant show the presence of the mechanically mixed layer (MML) with the adhesive wear mechanism. With increasing load, the abrasion, delamination, and MML mechanisms were dominant, and a significant reduction of COF and wear rate were observed. At the high temperature and high loads, the crushing of precipitates and their orientation in the wear sliding was caused to dwindle applied load and prevented the activation of other wear mechanisms.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. Effect of whisker alignment on microstructure, mechanical and thermal properties of Mg-SiCw/Cu composite fabricated by a combination of casting and severe plastic deformation (SPD)10.1016/j.jma.2022.11.004 ↗
2. Thermal cycles behavior and microstructure of AZ31/SiC composite prepared by stir casting10.1038/s41598-022-19410-2 ↗
3. Tribo-corrosive wear and mechanical properties of nanoparticles reinforced Mg-AZ91D composites10.1016/j.triboint.2022.108054 ↗
4. Influence of temperature on crystallographic orientation induced anisotropy of microscopic wear in an AZ91 Mg alloy10.1016/j.triboint.2021.107159 ↗
5. Tribological behavior of ZK60 magnesium matrix composite reinforced by hybrid MWCNTs/B4C prepared by stir casting method10.1016/j.triboint.2021.107299 ↗
6. Comparison of sustainable cooling systems used in the drilling repair of Mg-Al and Mg-Ti multi-material parts in the aeronautical industry10.1016/j.triboint.2022.107804 ↗
7. Wear behavior of the friction stir alloyed AZ31 Mg at different volume fractions of Al particles reinforcement and its enhanced quality attributes10.1016/j.triboint.2020.106268 ↗
8. Developing a Mg alloy with ultrahigh room temperature ductility via grain boundary segregation and activation of non-basal slips10.1016/j.ijplas.2023.103548 ↗
9. Deformation-induced dynamic precipitation of 14H-LPSO structure and its effect on dynamic recrystallization in hot-extruded Mg-Y-Zn alloys10.1016/j.ijplas.2023.103573 ↗
10. Microstructural changes caused by the creep test in ZK60 alloy reinforced by SiCp at Intermediate Temperature after KOBO extrusion and aging10.3390/ma16103885 ↗
11. Tribological behaviour of AZ31 magnesium alloy reinforced by bimodal size B4C after precipitation hardening10.1016/j.jma.2021.05.016 ↗
12. Effects of the microstructure and precipitation hardening on the thermal expansion behavior of ZK60 magnesium alloy
13. Investigation of mechanical properties and biocorrosion behavior of in situ and ex situ Mg composite for orthopedic implants10.1016/j.msec.2020.110974 ↗
14. Creep Behavior of ZK60 Alloy and ZK60/SiCw composite after extrusion and precipitation hardening10.1007/s12540-020-00877-5 ↗
15. Evaluation of whisker alignment and anisotropic mechanical properties of ZK60 alloy reinforced with SiCw during KOBO extrusion method10.1016/j.jmapro.2022.10.012 ↗
16. Sliding wear map for the magnesium alloy Mg-9Al-0.9 Zn (AZ91)10.1016/S0043-1648(00)00495-6 ↗
17. Tribological performance of silicone oil based Al2O3 nano lubricant for an Mg alloy subjected to sliding at elevated temperatures10.1016/j.triboint.2022.107779 ↗
18. Tribology and dynamic characteristics of textured journal-thrust coupled bearing considering thermal and pressure coupled effects10.1016/j.triboint.2023.108292 ↗
19. Tribological characterization of reinforced Fe matrix composites with hybrid reinforcement of C, Cu, and SiC particulates10.3390/cryst12050598 ↗
20. Design of Fe-SiC-Cu-G composite alloy and optimization of graphite contribution for high sliding speed applications10.1007/s12666-022-02562-0 ↗
21. Synergetic effects of surface texturing and solid lubricants to tailor friction and wear - a review10.1016/j.triboint.2020.106792 ↗
22. Novel utilization of liquid feedstock in high velocity air fuel (HVAF) spraying to deposit solid lubricant reinforced wear resistant coatings10.1016/j.jmatprotec.2021.117203 ↗
23. 2D SiP nanoflakes as new high-performance lubricant additive for steel/steel sliding contact10.1016/j.triboint.2022.107467 ↗
24. Preparation and wear resistance properties of thermosetting polyimide composites containing solid lubricant fillers10.1016/j.matchemphys.2019.122034 ↗
25. Optimization of wear behaviour for AA2219-MoS2 metal matrix composites in dry and lubricated condition10.1016/j.matpr.2019.11.087 ↗
26. Lubrication characteristics and wear mechanism mapping for hybrid aluminium metal matrix composite sliding under surfactant functionalized MWCNT-oil10.1016/j.triboint.2019.106152 ↗
27. Dry sliding wear behaviour of a conventional and recycled high pressure die cast magnesium alloys10.1016/j.matchar.2009.01.014 ↗
28. Microstructural evolution during accelerated tensile creep test of ZK60/SiCp composite after KoBo extrusion10.3390/ma15186428 ↗
29. Synthesis of biological base oils by a green process10.1515/gps-2022-0008 ↗
30. MWCNTs-TiO2 incorporated-Mg composites to improve the mechanical, corrosion and biological characteristics for use in biomedical fields10.3390/ma16051919 ↗
31. Lubricated tribology of hybrid AMMC–steel sliding contact: a comparative investigation between fully formulated commercial engine oils and surfactant functionalized MWCNT–base oil formulation10.1177/1350650119901221 ↗
32. Synthesis and characterization of hot extruded magnesium-zinc nano-composites containing low content of graphene oxide for implant applications10.1134/S1029959921040135 ↗
33. The effect of Mg(OH)2 nanoparticles on the rheological behavior of base engine oil SN500 HVI and providing a predictive new correlation of nanofluid viscosity10.1016/j.arabjc.2022.103767 ↗
34. J. Sunil, R. Maheswaran, R. Vettumperumal, K.K. Sadasivuni, Experimental Investigation on the Thermal Properties of NiO-Nanofluids, J. Nanofluids. 8 (n.d.) 1577–1582. https://www.ingentaconnect.com/content/asp/jon/2019/00000008/00000007/art00020.10.1166/jon.2019.1698 ↗
35. Monitoring of the physical and chemical properties of a gasoline engine oil during its usage10.1155/2012/819524 ↗
36. Graphene oxide encapsulated forsterite scaffolds to improve mechanical properties and antibacterial behavior10.1088/1748-605X/ac62e8 ↗
37. A study on the corrosion behavior and biological properties of polycaprolactone/ bredigite composite coating on biodegradable Mg-Zn-Ca-GNP nanocomposite
38. Improvement of rheological properties of invert drilling fluids by enhancing interactions of water droplets using hydrogen bonding linker10.1016/j.colsurfa.2016.07.011 ↗
39. Modeling the interfacial energy of surfactant-free Amphiphilic Janus nanoparticles from phase inversion in pickering emulsions10.1021/acs.langmuir.7b02331 ↗
40. Structural properties of span 80/Tween 80 reverse10.1021/acs.jpcb.8b03945 ↗
41. Microstructure development and biodegradation behavior of additively manufactured Mg-Zn-Gd alloy with LPSO structure10.1016/j.jmst.2022.09.059 ↗
42. A novel heterogeneous multi-wire indirect arc directed energy deposition for in-situ synthesis Al-Zn-Mg-Cu alloy: process, microstructure and mechanical properties
43. The tribological performance of 6061 aluminum alloy/graphite composite materials in oil lubrications with EP additives10.1016/0043-1648(96)06932-3 ↗
44. Synthesis of boride coatings on steel using plasma transferred arc (PTA) process and its wear performance10.1016/S0043-1648(02)00056-X ↗
45. The spearman correlation formula10.1126/science.22.558.309 ↗
46. Dry sliding wear behavior of additively manufactured CoCrWNixAly alloys
47. Tensile properties and microstructure of ZK60/SiCw composite after extrusion and aging10.1016/j.jallcom.2020.154709 ↗
48. Ultrasonic welding of AZ31B magnesium alloy and pure copper: microstructure, mechanical properties and finite element analysis10.1016/j.jmrt.2023.01.095 ↗
49. Critical length scale controls adhesive wear mechanisms10.1038/ncomms11816 ↗
50. Al₂O₃ nanoparticle addition to commercial magnesium alloys: multiple beneficial effects10.3390/nano2020147 ↗
51. Thermal oxidation and its effect on the wear of Mg alloy AZ31B10.1016/j.wear.2021.203673 ↗
52. Reinforced AZ91D magnesium alloy with thixomolding process facilitated dispersion of graphene nanoplatelets and enhanced interfacial interactions10.1016/j.msea.2021.140793 ↗
53. Effects of Zn/Gd ratio on the microstructures and mechanical properties of Mg-Zn-Gd-Zr alloys10.1016/j.msea.2017.03.117 ↗
54. Influence of specific second phases on corrosion behaviors of Mg-Zn-Gd-Zr alloys10.1016/j.corsci.2019.108419 ↗