Precipitation of ceramic particles in Fe-TiB2 and Fe-Ni-TiB2 cast steels during the sub-rapid solidification process
Source abstract
Abstract
Titanium diboride (TiB 2 ) particle reinforced steels were prepared by a sub-rapid solidification process using the in-situ method. Effects of the Ni concentration on the precipitation of TiB 2 ceramic particles were studied and modified in detail. The results show that the mechanically unfavorable-block TiB 2 -morphologies and the matrix constitutions change with the addition of alloy Ni. The Ni concentration in the iron matrix closes the primary δ-Fe ferrite phase zone, retards the precipitation of the primary TiB 2 particles, changes the residual interfacial lattice strain in α-Fe ferrite from tension to compression and promotes the ordered adoption of Fe atoms in (Ti, Fe)B 2, which results in the ceramic particles growth into the vermicular-shaped morphologies. Strongly coherent interfaces between a-Fe matrix and TiB 2 particles form in Fe-Ni-TiB 2 high-modulus steels (HMS) according to the generation of the compression lattice strains at α-Fe ferrite interfaces. The mechanical favorable interfaces are believed to be responsible for the obvious improvements in the mechanical properties, especially the tensile elongation, of Fe-Ni-TiB 2 HMS.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Additive manufacturing of high modulus steels: New possibilities for lightweight design
2. Revealing the interfacial plasticity and shear strength of a TiB2-strengthened high-modulus low density steel10.1016/j.jmps.2018.08.010 ↗
3. High modulus steels: a new requirement of automotive market How to take up challenge?10.1179/1879139514Y.0000000144 ↗
4. Improving the mechanical properties of Fe-TiB2 high modulus steels through controlled solidification process10.1016/j.actamat.2016.07.056 ↗
5. Solidified microstructures and elastic modulus of hypo-eutectic and hyper-eutectic TiB2-reinforces high-modulus steel10.1016/j.actamat.2019.06.052 ↗
6. Nanoparticle enabled high performance high modulus steels
7. Strengthening Fe-TiB2 based high modulus steels by precipitations10.1016/j.matdes.2017.03.042 ↗
8. In-situ metal matrix composite steels: Effect of alloying and annealing on morphology, structure and mechanical properties of TiB2 particle containing high modulus steels10.1016/j.actamat.2016.01.048 ↗
9. Interface structure and chemistry in a novel steel -based composite Fe-TiB2 obtained by eutectic solidification10.1016/j.actamat.2012.08.017 ↗
10. Microstructure refinement for high modulus in-situ metal matrix composite steels via controlled solidification of the system Fe-TiB210.1016/j.actamat.2015.06.017 ↗
11. Solidified microstructures and elastic modulus of hypo-eutectic and hyper-eutectic TiB2-reinforces high-modulus steel10.1016/j.actamat.2019.06.052 ↗
12. Crystallisation of amorphous Fe-Ti-B alloys as a design pathway for nano-structured high modulus steels10.1016/j.jallcom.2017.02.077 ↗
13. Effects of Mn additions on microstructure and properties of Fe-TiB2 based high modulus steels10.1016/j.matdes.2016.09.003 ↗
14. Microstructure and mechanical properties of Al-Mg-Si alloy fabricated by a short process based on sub-rapid solidification10.1016/j.jmst.2019.08.053 ↗
15. Influence of carbon addition on mechanical properties and microstructures of Ni-free Co–Cr–W alloys subjected to thermomechanical processing10.1016/j.jmbbm.2014.05.025 ↗
16. Rietveld analysis software for J-PARC10.1016/j.nima.2008.11.056 ↗
17. Phase composition in alloy steel
18. A prismatic sub-structure formed during solidification of metals10.1139/p53-003 ↗
19. The redistribution of solute atoms during the solidification of metals10.1016/0001-6160(53)90126-6 ↗
20. A stability function for explicit evaluation of the Mullins-Sekerka interface stability criterion10.1063/1.1713887 ↗
21. TEM study of the interface in ceramic-reinforced aluminum-based composites10.1016/S0254-0584(02)00593-X ↗
22. In situ analysis of plastic deformation of lath martensite during tensile process
23. Effect of non-isothermal deformation of austenite on ferrite transformation behavior studied by in-situ neutron diffraction10.1016/j.msea.2015.02.043 ↗
24. On the effect of Ni additions to Fe-Cr-B high modulus steels10.1016/j.matdes.2019.107624 ↗
25. Elastic constants of binary iron-base alloys10.1007/BF02643211 ↗
26. Iron and its dilute substitutional solid solution10.1007/BF02680580 ↗
27. Microstructure-based modeling of the deformation behavior of particle reinforced metal matrix composites10.1007/s10853-006-6572-1 ↗
28. Phase equilibria and structure of alloys Fe-TiB2, Fe-ZrB2, Fe-HfB2
29. Annealing of cold-worked austenitic stainless steels10.2355/isijinternational.43.135 ↗
30. Gibbs-Thomson effects in phase transformations10.1016/j.scriptamat.2004.12.026 ↗
31. The bond characters and phase stability effects of Cr, Mo and Ni in bulk γ-Fe(C)
32. Flemings · 1974 · 31
33. Influence of Ti microalloying on the formation of nanocrystalline structure in the 201L austenitic stainless steel during martensite thermomechanical treatment10.1016/j.msea.2013.07.014 ↗