Influence of Ag on microstructure, mechanical properties and tribological properties of as-cast Al-33Zn-2Cu high-zinc aluminum alloy
Source abstract
Abstract
The effect of Ag on the microstructure, mechanical properties, and tribological properties of Al-33Zn-2Cu alloys was investigated. The results show that the mechanical properties of the high-zinc aluminum alloy increase linearly with increasing silver content. The yield strength, tensile strength and elongation of the Al-33Zn-2Cu-0.6Ag alloy are 370 MPa, 433 MPa and 8.2% respectively. Wear resistance was also significantly improved. As the silver content in the Al-33Zn-2Cu alloy increases, the density of the η` phase in the α matrix increases. The addition of Ag aggravates the discontinuous precipitation of the α + η phase, resulting in the inhibition of the continuous large α + η phase in the alloy and the transformation into small discontinuous precipitation phases. Besides, as the Ag content increases, the lamellar α + η phases formed at the grain boundaries become finer and denser. This study may provide innovative ideas for alloy design of high-zinc aluminum alloys.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (72)
Show source-provided references
1. Softening of nanostructured Al-Zn and Al-Mg alloys after severe plastic deformation[J]10.1016/j.actamat.2006.04.025 ↗
2. Softening by severe plastic deformation and hardening by annealing of aluminum-zinc alloy: Significance of elemental and spinodal decompositions[J]10.1016/j.msea.2014.05.026 ↗
3. Thermal evolution and grain boundary phase transformations in severely deformed nano grained Al-Zn alloys[J]10.1016/j.actamat.2008.08.021 ↗
4. Dynamic precipitation of Al-Zn alloy during rolling and accumulative roll bonding[J]10.1080/09500839.2015.1119322 ↗
5. A microstructure-based model for describing the material properties of Al–Zn alloys during high-pressure torsion[J]10.1016/j.ijplas.2014.01.009 ↗
6. Tuning of CeO2-MnO2 nano composite in Al-Zn alloy matrix for effective activation[J]
7. Effects of pressure and sliding speed on the friction and wear properties of Al-40Zn-3Cu-2Si alloy: A comparative study with SAE 65 bronze[J]10.1016/j.msea.2008.06.008 ↗
8. Characteristics and microstructure of newly designed Al–Zn-based alloys for the die-casting process[J]10.1016/j.jallcom.2016.02.127 ↗
9. Liquid immiscible alloys[J]10.1016/0927-796X(95)00180-8 ↗
10. The influence of heat treatment on the sliding wear behavior of a ZA-27 alloy[J]10.1016/j.triboint.2009.04.016 ↗
11. The effect of silver on wear behaviour of zinc-aluminum-based ZA-12 alloy produced by gravity casting[J]10.1016/j.matchar.2013.12.015 ↗
12. Fabrication of Al-35Zn alloys with excellent damping capacity and mechanical properties[J]10.1016/j.jallcom.2017.06.091 ↗
13. Unusual super-ductility at room temperature in an ultrafine-grained aluminum alloy[J]10.1007/s10853-010-4588-z ↗
14. The effects of trace Sc and Zr on microstructure and internal friction of Zn-Al eutectoid alloy[J]10.1016/j.msea.2002.12.007 ↗
15. Damping behavior of discontinuously reinforced ai alloy metal-matrix composites[J]10.1007/BF02669639 ↗
16. Ultrafine grained structures resulting from SPD-Induced phase transformation in Al-Zn Alloys[J]10.1002/adem.201500151 ↗
17. First principle investigation of crystal lattice structure, thermodynamics and mechanical properties in ZnZrAl2 intermetallic compound[J]10.1016/j.ssc.2016.08.013 ↗
18. New developments of high-zinc Al-Zn-Cu-Mn cast alloys[J]
19. The efficiency analysis of grain refinement in high-zinc aluminum alloys with Ti-containing master alloy[J]10.1080/13640461.2018.1493168 ↗
20. Strength properties examination of high zinc aluminum alloys inoculated with Ti addition[J]10.1007/s41230-017-6098-y ↗
21. Krajewski W.K., Greer A.L., Piwowarski G., et al. Property enhancement by grain refinement of zinc-aluminum foundry alloys[J]. IOP Conference Series: Materials Science and Engineering, 2016, 117(1): 271–278.〈http://iopscience.iop.org/1757–899X/117/1/012004〉.10.1088/1757-899X/117/1/012004 ↗
22. Trends in the development of high-aluminum zinc alloys of stable structure and properties[J]10.2478/amm-2013-0084 ↗
23. Main directions of recent works on Al-Zn-based alloys for foundry engineering[J]10.1007/s11665-019-04048-5 ↗
24. Effects of titanium addition on structural, mechanical, tribological, and corrosion properties of Al25Zn3Cu and Al25Zn3Cu3Si alloys[J]10.1016/S1003-6326(20)65214-1 ↗
25. Effects of Sc addition and rolling on the microstructure and mechanical properties of Al–35Zn alloys[J]10.1016/j.msea.2017.07.042 ↗
26. Effect of scandium on microstructure and mechanical properties of high zinc concentration aluminum alloys[J]10.1016/j.matchar.2017.03.028 ↗
27. Effects of Mg and RE additions on the semi-solid microstructure of a zinc alloy ZA27[J]10.1016/j.stam.2004.01.002 ↗
28. Effects of silicon content on the microstructural features and mechanical and sliding wear properties of Zn-40Al-2Cu-(0-5)Si alloys[J]10.1016/j.msea.2005.05.078 ↗
29. Effects of Silicon addition and test parameters on sliding wear characteristics of Zinc-Based alloy containing 37.5% aluminum[J]10.2320/matertrans1989.38.701 ↗
30. Sliding wear response of a zinc-based alloy and its composite and comparison with a gray cast iron: influence of external lubrication and microstructural features[J]10.1016/j.msea.2004.10.031 ↗
31. Effects of silicon content on the mechanical properties and lubricated wear behaviour of Al-40Zn-3Cu-(0-5)Si alloys[J]10.1007/s11249-008-9299-0 ↗
32. Effect of Zn and Cu Content on Microstructure, Hardness and Tribological Properties of Cast Al-Zn-Cu Alloys[J]10.4028/www.scientific.net/JERA.27.1 ↗
33. Effect of copper content on the mechanical and sliding wear properties of monotectoid-based zinc-aluminum-copper alloys[J]10.1016/S0301-679X(03)00113-0 ↗
34. Relationships between cooling rate, copper content and mechanical properties of monotectoid based Zn-Al-Cu alloys[J]10.1016/j.matchar.2003.12.003 ↗
35. Mechanical properties and abrasive wear behaviors of in situ nano-TiC x /Al–Zn–Mg–Cu composites fabricated by combustion synthesis and hot press consolidation[J]10.1016/j.acme.2017.06.009 ↗
36. Precipitation of metastable ϵ-phase in a hypereutectic zinc-aluminum alloy containing copper[J]10.1016/0956-7151(91)90005-L ↗
37. Effect of specific pressure on microstructure and mechanical properties of squeeze casting ZA27 alloy[J]10.1016/S1003-6326(09)60097-2 ↗
38. R. Bauri, D. Yadav. Metal matrix composites by friction stir processing [M], 2017.
39. Evolution of microstructure and properties of Ag and Si-doped AlMg alloys[J]
40. Effects of Ag on the age hardening response and intergranular corrosion resistance of Al-Mg alloys [J]10.1016/j.matchar.2018.10.025 ↗
41. Influence of Zn and/or Ag additions on microstructure and properties of Al-Mg based alloys[J]
42. Effects of microalloying tin and combined addition of silver and tin on the formation of precipitate free zones and mechanical properties in Al-Zn-Mg alloys[J]10.2320/matertrans.L-MZ201123 ↗
43. Atom probe tomography of nanoscale microstructures within precipitate free zones in Al-Zn-Mg(-Ag) alloys[J]10.1016/j.actamat.2010.06.046 ↗
44. Microstructural evolution during ageing of Al–Cu–Li–x alloys[J]10.1016/j.actamat.2013.12.001 ↗
45. Microchemical and microstructural characterization of the early stages of the discontinuous precipitation reaction in Al-22 at%Zn alloy[J]10.1007/s00604-003-0167-1 ↗
46. Combined in situ and EBSD studies of discontinuous precipitation in Al-22 at%Zn alloy[J]10.1016/j.matchar.2019.109889 ↗
47. Achieving high damping capacity and strength simultaneously in a high-zinc aluminum alloy via melt spinning and hot extrusion[J]
48. Fine precipitation scenarios of AlZnMg(Cu) alloys revealed by advanced atomic-resolution electron microscopy study Part I: Structure determination of the precipitates in AlZnMg(Cu) alloys[J]10.1016/j.matchar.2014.11.028 ↗
49. Effects of friction stir processing and minor Sc addition on the microstructure, mechanical properties, and damping capacity of 7055 Al alloy[J]10.1016/j.matchar.2017.11.030 ↗
50. Simultaneous increase in strength and ductility by decreasing interface energy between Zn and Al phases in cast Al-Zn-Cu alloy[J]10.1038/s41598-017-12286-7 ↗
51. Characterization of precipitates in an Al-Zn-Mg alloy processed by ECAP and subsequent annealing[J]
52. Friction and wear properties of Zn−25Al-based bearing alloys [J]10.1080/10402004.2014.880540 ↗
53. Microstructure and mechanical properties of TiB-containing Al-Zn binary alloys[J]10.1016/j.jmst.2016.04.016 ↗
54. Effects of high Zn content on the microstructure and mechanical properties of Al-Zn-Cu gravity-cast alloys[J]10.1016/j.msea.2016.09.022 ↗
55. Evaluation of microstructure, damping capacity and mechanical properties of Al-35Zn and Al-35Zn-0.5Sc alloys[J]10.1016/j.jallcom.2017.12.234 ↗
56. Increasing toughness by promoting discontinuous precipitation in Cu–Ni–Si alloys[J]10.1080/09500839.2016.1189099 ↗
57. Optimization of conductivity and strength in Cu-Ni-Si alloys by suppressing discontinuous precipitation[J]10.1007/s12540-016-6156-9 ↗
58. Increasing strength and conductivity of Cu alloy through abnormal plastic deformation of an intermetallic compound[J]10.1038/srep30907 ↗
59. Kinetics and mechanisms of precipitation in an Al-0.2wt% Sc alloy[J]10.1016/j.msea.2005.02.015 ↗
60. Microstructure and mechanical properties of a high-Zn aluminum alloy prepared by melt spinning and extrusion[J]10.1016/j.jallcom.2019.152990 ↗
61. Microstructural evolutions and enhanced mechanical performance of novel Al-Zn die-casting alloys processed by squeezing and hot extrusion[J]10.1016/j.jmatprotec.2021.117063 ↗
62. Savaşkan · 2017
63. Creep behaviour of eutectic Zn-Al-Cu-Mg alloys[J]10.1016/j.msea.2018.03.068 ↗
64. Hrem study and structure modeling of the η′ phase, the hardening precipitates in commercial Al-Zn-Mg alloys[J]10.1016/S1359-6454(99)00138-X ↗
65. Wear resistance and microstructure of Zn-Al-Si and Zn-Al-Cu alloys[J]10.1016/0043-1648(87)90245-6 ↗
66. Optimization of wear parameters of binary Al-25Zn and Al-3Cu alloys using design of experiments[J]10.1007/s12613-018-1701-9 ↗
67. Mechanical and tribological properties of Al-40Zn-Cu alloys[J]10.1016/j.triboint.2008.04.008 ↗
68. Wear behavior of aluminum alloys at slow sliding speeds[J]10.1080/10402004.2015.1027432 ↗
69. Dry sliding friction and wear properties of Al-25Zn-3Cu-(0-5)Si alloys in the as-cast and heat-treated conditions[J]10.1007/s11249-010-9667-4 ↗
70. Effect of nickel additions on the mechanical and sliding wear properties of Al-40Zn-3Cu alloy[J]10.1016/j.wear.2009.10.002 ↗
71. High damping capacity of Al-40Zn alloys with fine grain and eutectoid structures via Yb alloying[J]
72. Study of Mechanical properties and erosion wear behaviour of novel Al-25Zn alloy/SiC/Graphite hybrid composites[J]