Effect of solid solution process on the structure and properties of Cu-Cr-Mg alloy in the aging state
Source abstract
Abstract
In this study, Cu-Cr-Mg alloy wires were prepared by up-drawing continuous casting and multi-pass drawing. The effect of the solid solution process on the strength and electrical conductivity of the Cu-Cr-Mg alloy was investigated. The solid solution degree of Cu-Cr-Mg alloys with different solid solution processes was evaluated by XRD. The types and morphologies of nanoprecipitates of the two alloys during different thermomechanical treatments were compared by selected area electron diffraction in TEM, and the degree of recrystallization of the peak-aged Cu-Cr-Mg alloy was analyzed by EBSD. The results showed that the degree of supersaturated solid solution of the as-cast Cu-Cr-Mg alloy was comparable to that of the as-cast Cu-Cr-Mg alloy after holding at 950 ℃ for 1 h and water quenching. Meanwhile, the strength of the as-cast Cu-Cr-Mg alloy was 52.2 MPa higher than that of the solution-treated Cu-Cr-Mg alloy, and the decrease in conductivity was only 6.3% IACS. The microstructure results showed that a large number of dispersed nanoscale precipitates existed in the matrix of both alloys, and the precipitates were close in size. The results of the strengthened model calculations are also close to the experimental results.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. Hot deformation characteristics and processing maps of the Cu-Cr-Zr-Ag alloy10.1007/s11665-016-1937-3 ↗
2. Effect of rolling and aging processes on microstructure and properties of Cu-Cr-Zr alloy10.1016/j.msea.2017.05.114 ↗
3. Effects of Co and Si additions and cryogenic rolling on structure and properties of Cu–Cr alloys
4. Optimizing the strength, ductility and electrical conductivity of Cu-Cr-Zr alloy by rotary swaging and aging treatment10.1016/j.msea.2019.01.002 ↗
5. Effects of Zr and (Ni, Si) additions on properties and microstructure of Cu-Cr alloy10.1016/j.jallcom.2013.08.146 ↗
6. Atomic scale investigation of Cr precipitation in copper10.1016/j.actamat.2012.01.038 ↗
7. Effect of precipitation on mechanical and wear properties of ultrafine-grained Cu-Cr-Zr alloy10.1016/j.wear.2014.01.007 ↗
8. Research status and Prospect of rapidly solidified high strength and high conductivity copper alloy
9. Strengthening in rapidly solidified age hardened Cu-Cr and Cu-CU-Zr alloys10.1016/S1359-6454(96)00142-5 ↗
10. Investigation on the microstructure and mechanical properties of the spray-formed Cu-Cr alloys
11. Microstructures and electrical and mechanical properties of Cu-Cr-alloys fabricated by selective laser melting
12. H. Li, Study on microstructure evolution and properties of directionally solidified Cu-Cr-Ti hypereutectic alloy, D. Jiangxi University of Science and Technology, 2018.
13. A novel route for strengthening copper rods: non-solution heat treatment combined with pre-aging10.1016/j.jmatprotec.2019.116290 ↗
14. Grain refinement kinetics and strengthening mechanisms in Cu–0.3Cr–0.5Zr alloy subjected to intense plastic deformation10.1016/j.msea.2015.12.038 ↗
15. Y.H. Rong, C.H. Jiang, Characterization of material microstructure, M. Shanghai, Shanghai Jiaotong University Press, 2012.
16. Evolution of the microstructure and properties of a Cu–Cr-(Mg) Alloy upon thermomechanical treatment10.1016/j.jallcom.2020.157582 ↗
17. Grain refinement kinetics and strengthening mechanisms in Cu-0.3Cr-0.5Zr alloy subjected to intense plastic deformation10.1016/j.msea.2015.12.038 ↗
18. On the grain size softening in nanocrystalline materials10.1016/S1359-6462(00)00320-1 ↗
19. Influence of stacking-fault energy on microstructural characteristics of ultrafine-grain copper and copper-zinc alloys10.1016/j.actamat.2007.10.053 ↗
20. Strengthening mechanisms in a high-strength bulk nanostructured Cu-Zn-Al alloy processed viacryomilling and spark plasma sintering10.1016/j.actamat.2012.09.036 ↗
21. Smallman · 2007 · 395
22. The precipitation behavior and strengthening of a Cu–2.0 wt% Be alloy10.1016/j.msea.2012.08.007 ↗
23. Phase transformation in Cu–Cr–Zr–Mg alloy10.1016/j.matlet.2007.03.085 ↗
24. Electrical conductivity versus strength in a precipitation hardened alloy10.1016/0956-7151(92)90015-7 ↗
25. Effect of cold rolling on aging precipitation behavior and mechanical properties of Cu–15Ni–8Sn alloy10.1016/j.jallcom.2020.156275 ↗
26. Study of deformation and aging behaviors of a hot rolled–quenched Cu–Cr–Zr–Mg–Si alloy during thermomechanical treatments10.1016/j.matdes.2012.03.003 ↗
27. Enhancing strength and electrical conductivity of Cu–Cr composite wire by two-stage rotary swaging and aging treatments10.1016/j.compositesb.2021.109567 ↗
28. Phase transformation in Cu–Cr–Zr–Mg alloy10.1016/j.matlet.2007.03.085 ↗
29. Hall–Petch relation, boundary strengthening10.1016/j.scriptamat.2004.06.002 ↗
30. E.O. Hall, The deformation and ageing of mild steel: II characteristics of the Lüders deformation, Proc. Phys. Soc. Lond. Sect. B 64 (1951) 742–747.10.1088/0370-1301/64/9/302 ↗
31. The cleavage strength of polycrystals
32. Fracture and strength of solids10.1088/0034-4885/12/1/309 ↗
33. Phase transformation behaviors and properties of a high strength Cu-Ni-Si alloy10.1016/j.msea.2017.05.001 ↗
34. Precipitation-hardening of metals
35. M.A. Meyers, Mechanical Behavior of Materials (third ed.), Aircr. Eng. 81 (2009).10.1108/aeat.2009.12781bae.001 ↗