Lamellar instabilities during scanning laser melting of Al–Cu eutectic and hypoeutectic thin films
Source abstract
Abstract
Abstract Scanning laser melting was employed to investigate directional solidification in Al–Cu thin films, 200 and 500 nm thick. The Al–Cu alloy films, with both eutectic and hypoeutectic compositions, were co-deposited on fused silica substrates by magnetron sputtering. Melting of the films was carried out in air using a CW laser, as a function of the scan velocity, v, up to 5 cm/s. For eutectic films, regular lamellar microstructure was observed over the entire range of velocities studied. Interlamellar spacings, λ, below 50 nm were readily produced. Results were found to be consistent with studies on bulk Al–Cu alloys, obeying the classic steady state lamellar growth relationship, λ2v = K. However, the value of the constant, K is significantly larger in thin films when compared to bulk. This is attributed to constraints on mechanisms for spacing adjustment in two-dimensional eutectic systems. In the hypoeutectic thin films, a complex lamellar structure was observed as the scan velocity was reduced. Regions of straight lamellae, oscillatory lamellae, solitary tilt waves, and recurring extreme lamellar branching events coexisted across the melt track. Fourier analysis was used to quantify the chaotic area fraction of the films. The transition to chaos occurred as the G/v ratio increased, attributed to approaching a re-entrant eutectic-to-dendritic transition from above. Approaches to further refine laser melting in thin eutectic films in order to better control solidification processes are discussed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Solidification and crystal growth phenomena · Aluminum Alloy Microstructure Properties · Metallic Glasses and Amorphous Alloys
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. Rapid solidification of Al-Cu eutectic alloy by laser remelting10.1016/0001-6160(89)90203-4 ↗
2. Rod and lamellar growth of eutectic
3. Experimental determination of cooling rates in selectively laser-melted eutectic Al-33Cu
4. A selective laser melting and solution heat treatment refined Al–12Si alloy with a controllable ultrafine eutectic microstructure and 25% tensile ductility10.1016/j.actamat.2015.05.017 ↗
5. Synthesis and thermal transport of eco-friendly Fe-Si-Ge alloys with eutectic/eutectoid microstructure10.1016/j.matchemphys.2017.12.038 ↗
6. Self-assembled nanometer lamellae of thermoelectric PbTe and Sb 2 Te 3 with epitaxy-like Interfaces10.1021/cm062121p ↗
7. The exchange-spring magnet: a new material principle for permanent magnets10.1109/20.102931 ↗
8. A review on nano-/ultrafine advanced eutectic alloys10.1016/j.jallcom.2020.154226 ↗
9. Directionally solidified thin-film eutectic alloys10.1063/1.328485 ↗
10. Periodic Si‐CoSi2 eutectic structures10.1063/1.338282 ↗
11. Lamellar-structured Ni-silicide film formed by eutectic solidification10.1016/j.jallcom.2018.08.257 ↗
12. Determination of the Jackson-Hunt constants of the In-In2Bi eutectic alloy based on in situ observation of its solidification dynamics10.1016/j.actamat.2011.08.036 ↗
13. Growth of eutectic alloy thin films10.1016/0025-5416(84)90203-9 ↗
14. Solidification of CuAl2-Al eutectic alloys
15. High-speed solidification of several eutectic alloys10.1016/0001-6160(70)90125-2 ↗
16. The solidification of metals
17. Determination of cooling rate in splat-cooling from scale of microstructure
18. Interlamellar spacing measurements in the Sn-Pb and Al-CuAl2 eutectic systems10.1007/BF02656603 ↗
19. The effect of fluid flow on eutectic growth10.1007/s11661-005-0083-6 ↗
20. The freezing of some continuous binary eutectic mixtures10.1080/14786436408225381 ↗
21. Eutectic spacing selection in Al–Cu system10.1179/mst.1994.10.4.312 ↗
22. Binary eutectic solidification
23. Real-time study of thin and bulk eutectic growth in succinonitrile-(d)camphor alloys10.1016/j.jcrysgro.2006.11.271 ↗
24. Experimental determination of the stability diagram of a lamellar eutectic growth front10.1103/PhysRevE.56.780 ↗
25. Morphological instabilities of lamellar eutectics10.1007/BF02648952 ↗
26. Oscillatory lamellar microstructure in off-eutectic Al-Cu alloys10.1103/PhysRevB.42.833 ↗
27. On the steady-state temperature rise during laser heating of multilayer thin films in optical pump–probe techniques10.1115/1.4038713 ↗
28. Substrate thermal conductivity controls the ability to manufacture microstructures via laser-induced direct write10.1063/1.5016073 ↗
29. Tilt bifurcation and dynamical selection by tilt domains in thin-film lamellar eutectic growth: experimental evidence of a tilt bifurcation10.1103/PhysRevA.45.7320 ↗
30. Theory of eutectic growth under rapid solidification conditions10.1016/0001-6160(87)90176-3 ↗
31. Two-phase eutectic growth in Al-Cu and Al-Cu-Ag10.1007/s11661-018-4488-4 ↗
32. The melting behavior of aluminum nanoparticles10.1016/j.tca.2007.07.007 ↗
33. The measurement of Al-Cu dendrite tip and eutectic interface temperatures and their use for predicting the extent of the eutectic range10.1016/0022-0248(76)90260-8 ↗
34. In-situ observation of eutectic growth in Al-based alloys by light microscopy10.1016/j.jcrysgro.2013.02.033 ↗
35. Eutectic growth in three dimensions10.1007/s11661-007-9163-0 ↗
36. Eutectic dynamics: a host of new states10.1103/PhysRevE.51.R2751 ↗
37. Eutectic spacing selection in lead-based alloy systems10.1007/BF02665018 ↗
38. Lamellar eutectic growth of CBr4-C2C16: effect of crystal anisotropy on lamellar orientations and wavelength dispersion10.1016/0022-0248(92)90058-Q ↗
39. Rapidly solidified AlCu alloys-I. experimental determination of the microstructure selection map10.1016/0956-7151(93)90237-M ↗
40. Beyond steady-state lamellar eutectic growth10.1103/PhysRevLett.59.71 ↗
41. Stability of a planar interface during solidification of a dilute binary alloy10.1063/1.1713333 ↗
42. Dendrite growth in eutectic alloys: the coupled zone10.1179/095066079790136408 ↗
43. Rapidly solidified Al-Cu alloys—II. Calculation of the microstructure selection map
44. Laser resolidification of the AlAl2Cu eutectic: the coupled zone10.1016/0956-7151(92)90454-M ↗
45. Solidification phase and microstructure selection maps for Fe-Cr-Ni alloys10.2355/isijinternational.39.1270 ↗
46. Metastable phase diagrams and rapid solidification processing10.2355/isijinternational.35.566 ↗
47. Solidification microstructure selection in the Al-rich Al-La, Al-Ce and Al-Nd systems10.1016/S0022-0248(98)00955-5 ↗
48. Revisiting solidification microstructure selection maps in the frame of additive manufacturing
49. Solidification microstructure of laser remelted Al2O3-ZrO2 eutectic10.1016/S1359-6454(97)00198-5 ↗
50. Microstructure selection maps for Al-Fe alloys10.1016/0956-7151(95)00039-X ↗
51. An experimental method for the in situ observation of eutectic growth patterns in bulk samples of transparent alloys10.1016/j.jcrysgro.2007.05.035 ↗