Fabrication and interface optimization of continuous CF/Al composites with different reinforcement volume fraction
Source abstract
Abstract
Interface is the key factor to determine the properties of composites. In this work, the Ni coated continuous CF/Al composites were fabricated via twin-roll casting method. After interface optimization, the interfacial bonding strength was enhanced and the dispersion of carbon fibers was improved. The effect of reinforcement volume fraction on microstructure, mechanical properties and strengthening mechanism of CF/Al composites was studied. The microstructural showed that the increase of reinforcement volume fraction was easy to cause more defects in composites. Transmission electron microscopy (TEM) and thermodynamic calculation were used to characterize the interfacial phase composition of composites after interface optimization. The results revealed that the exterior of carbon fibers bundle was mainly composed of Al 3 Ni intermetallic phase, and there was no obvious Al 4C 3 phases were found interior of the CFs bundle. In addition, the composites with 13.6 vol% CFs had the best UTS of 218.7 MPa and well dispersion. Furthermore, Vickers hardness test and Nano-indentation results showed that Al-Ni intermetallic compound can enhance the whole hardness of CF/Al composites. Dislocation strengthening in the Al-Ni intermetallic compound region was observed by TEM. The interface evolution mechanism of CF/Al composites were revealed for the first time.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Fiber-reinforced polymer composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (67)
Show source-provided references
1. Carbon fiber reinforced metal matrix composites: fabrication processes and properties10.1016/j.compositesa.2016.10.032 ↗
2. Interfacial performance of high-performance fiber-reinforced composites improved by cold plasma treatment: a review
3. Processing, structure and thermal conductivity correlation in carbon fibre reinforced aluminium metal matrix composites10.1016/j.matdes.2018.06.059 ↗
4. Carbon materials reinforced aluminum composites: a review10.1007/s40195-014-0160-1 ↗
5. Thermal response of the two-directional high-thermal-conductive carbon fiber reinforced aluminum composites with low interface damage by a vacuum hot pressure diffusion method10.1016/j.jallcom.2022.164195 ↗
6. Mechanical properties of a novel fiber metal laminate based on a carbon fiber reinforced Zn-Al alloy composite10.1016/j.msea.2018.10.050 ↗
7. Characterization of fibre/matrix interfaces in carbon/carbon composites10.1016/j.compscitech.2008.09.023 ↗
8. TEM study of carbon fibre reinforced aluminium matrix composites: influence of brittle phases and interface on mechanical properties10.1016/S0955-2219(00)00021-2 ↗
9. Effect of aluminum carbide on thermal conductivity of the unidirectional CF/Al composites fabricated by low pressure infiltration process10.1016/j.compscitech.2014.03.022 ↗
10. In situ chemical vapor deposition of metals on vapor-grown carbon fibers and fabrication of aluminum-matrix composites reinforced by coated fibers10.1007/s10853-017-1921-9 ↗
11. Enhancing the electrical insulation of highly thermally conductive carbon fiber powders by SiC ceramic coating for efficient thermal interface materials10.1016/j.compositesb.2021.109398 ↗
12. Formation of laminated nano-coatings for enhanced anti-oxidation and electromagnetic wave absorbing properties of carbon fiber10.1016/j.jmrt.2020.06.050 ↗
13. Electrical resistivity of electroless nickel coated carbon fibers10.1016/S0040-6090(01)00809-4 ↗
14. Improved wettability and mechanical properties of metal coated carbon fiber-reinforced aluminum matrix composites by squeeze melt infiltration technique10.1016/S1003-6326(21)65498-5 ↗
15. Friction and wear properties of copper matrix composites reinforced with short carbon fibers10.1016/j.matdes.2006.11.011 ↗
16. Processing, structure and thermal conductivity correlation in carbon fibre reinforced aluminium metal matrix composites10.1016/j.matdes.2018.06.059 ↗
17. Enhancement of fiber–matrix adhesion in carbon fiber reinforced Al-matrix composites with an optimized electroless plating process10.1016/j.compositesa.2020.106258 ↗
18. Electroless carbon fibers: a new route for improving mechanical property and wettability of composites10.1016/j.surfcoat.2018.11.072 ↗
19. Effects of nickel coating thickness on electric properties of nickel/carbon hybrid fibers10.1016/j.surfcoat.2010.12.007 ↗
20. Fabrication of woven carbon fibers reinforced Al–Mg (95–5 wt%) matrix composites by an electromagnetic casting process10.1016/j.jmatprotec.2015.06.040 ↗
21. Composite electroplating of Cu–SiO2 nano particles on carbon fiber reinforced epoxy composites10.1016/j.apsusc.2009.04.148 ↗
22. Simple and fast fabrication of conductive silver coatings on carbon fabrics via an electroless plating technique10.1016/j.matlet.2017.03.070 ↗
23. Low-pressure processing and microstructural evaluation of unidirectional carbon fiber-reinforced aluminum-nickel matrix composites10.1016/j.jmatprotec.2019.01.032 ↗
24. Fabrication of in situ carbon fiber/ aluminum composites via friction stir processing: evaluation of microstructural, mechanical and tribological behaviors10.1016/j.compositesb.2017.12.001 ↗
25. Microstructure and tensile properties of 2014 Al alloy reinforced with continuous carbon fibers manufactured by gas pressure infiltration10.1016/j.msea.2004.08.075 ↗
26. Production and mechanical characterization of Ni-coated carbon fibers reinforced Al-6063 alloy matrix composites10.1016/j.jallcom.2019.02.043 ↗
27. The effect of nickel coating on the mechanical properties and failure modes of continuous carbon fiber reinforced aluminum matrix composites10.1016/j.jallcom.2022.164134 ↗
28. Fabrication of carbon fibers reinforced Al-matrix composites in pulsed magnetic field10.1016/j.jmrt.2020.12.100 ↗
29. An investigation on underwater shock consolidated carbon fiber reinforced Al composites10.1016/S0924-0136(02)01117-2 ↗
30. Liquid rolling of woven carbon fibers reinforced Al5083-matrix composites10.1016/j.matdes.2016.01.074 ↗
31. Interfacial reaction induced efficient load transfer in few-layer graphene reinforced Al matrix composites for high-performance conductor10.1016/j.compositesb.2018.12.018 ↗
32. Interface and thermal expansion of carbon fiber reinforced aluminum matrix composites10.1016/S1003-6326(09)60433-7 ↗
33. Study on defects of 2D-Cf/Al composite prepared by liquid-solid extrusion following vacuum infiltration technique10.1007/s00170-016-8768-0 ↗
34. W.P. Mu, J.B. Lin, Yi Gong, D.X. Wu, E.Q. Liu, Microstructure and mechanical properties of Ni-coated continuous carbon fibers reinforced pure aluminum matrix composites prepared by twin-roll casting method, Adv. Eng. Mater. https://doi.org/10.1002/adem.202100420.10.1002/adem.202100420 ↗
35. Fabrication of continuous carbon-fibers reinforced aluminum matrix composites and coating evolution during heat treatment
36. Effect of Al2O3 coating thickness on microstructural characterization and mechanical properties of continuous carbon fiber reinforced aluminum matrix composites10.1016/j.msea.2020.139839 ↗
37. Deposition of copper thin films by plasma enhanced pulsed chemical vapor deposition for metallization of carbon fiber reinforced plastics10.1016/j.surfcoat.2016.07.029 ↗
38. Electrical resistivity of electroless nickel coated carbon fibers10.1016/S0040-6090(01)00809-4 ↗
39. Effect of reinforcement volume fraction and T6 heat treatment on microstructure, thermal and mechanical properties of mesophase pitch-based carbon fiber reinforced aluminum matrix composites10.1016/j.msea.2021.142469 ↗
40. Effects of volume fraction of SiC particles on mechanical properties of SiC/Al composites10.1016/S1003-6326(09)60040-6 ↗
41. In situ infiltration behavior and interfacial microstructure evolution between Al and carbon fibers10.1016/j.jallcom.2020.157120 ↗
42. Friction stir processing of Al3Ni intermetallic particulate reinforced cast aluminum matrix composites: microstructure and tensile properties10.1016/j.jmrt.2020.02.060 ↗
43. Interface study of carbon fiber reinforced Al–Cu composites10.1016/j.jallcom.2010.04.081 ↗
44. Effects of graphene content on microstructures and tensile property of graphene-nanosheets / aluminum composites10.1016/j.jallcom.2016.12.147 ↗
45. Effectively enhanced load transfer by interfacial reactions in multi-walled carbon nanotube reinforced Al matrix composites10.1016/j.actamat.2016.12.022 ↗
46. Interface and interfacial reactions in multi-walled carbon nanotube reinforced aluminum matrix composites10.1016/j.carbon.2015.10.016 ↗
47. Fabrication and characteristic of 2024Al matrix composites reinforced by carbon fibers and ZrCp by spark plasma sintering10.1016/j.jallcom.2021.161543 ↗
48. Fabrication of aluminum matrix composites reinforced with Ni-coated graphene nanosheets10.1016/j.msea.2019.03.068 ↗
49. Process optimization, microstructure characterization and thermal properties of mesophase pitch-based carbon fiber reinforced aluminum matrix composites fabricated by vacuum hot pressing10.1016/j.compositesb.2021.108746 ↗
50. Room-temperature direct bonding of diamond and Al10.1016/j.scriptamat.2018.09.016 ↗
51. Graphite film/aluminum laminate composites with ultrahigh thermal conductivity for thermal management applications10.1016/j.matdes.2015.10.146 ↗
52. Infiltration behavior and mechanism in semi-solid rolling of carbon fibers reinforced Al-matrix composite10.1016/j.matdes.2019.108102 ↗
53. Effect of aluminum carbide on thermal conductivity of the unidirectional CF/Al composites fabricated by low pressure infiltration process10.1016/j.compscitech.2014.03.022 ↗
54. Wettability of carbon by aluminum and aluminum alloys10.1016/S0921-5093(98)00759-X ↗
55. Fabrication of aluminium composites reinforced with carbon fibers by a centrifugal infiltration process10.1016/j.compositesa.2010.07.014 ↗
56. Processing and properties of copper-coated carbon fibre reinforced aluminium alloy composites10.1016/j.jmatprotec.2008.05.002 ↗
57. Fabrication and mechanical properties of Cu-coated woven carbon fibers reinforced aluminum alloy composite10.1016/j.matdes.2013.12.064 ↗
58. Development and characterization of liquid carbon fibre reinforced aluminium matrix composite10.1016/j.jmatprotec.2008.12.012 ↗
59. Effect of interfacial microstructure on the thermal-mechanical properties of mesophase pitch-based carbon fiber reinforced aluminum composites10.1016/j.jallcom.2018.04.330 ↗
60. Strength and interfacial reaction of high modulus carbon fiber-reinforced aluminum alloys10.2320/matertrans1960.26.563 ↗
61. Hall–Petch relation and boundary strengthening10.1016/j.scriptamat.2004.06.002 ↗
62. Microstructures and mechanical properties of nano-C and in situ Al2O3 reinforced aluminium matrix composites processed by equal-channel angular pressing10.1016/j.jallcom.2021.160159 ↗
63. Analysis of the friction and wear of graphene reinforced aluminum metal matrix composites using machine learning models
64. An approach for homogeneous carbon nanotube dispersion in Al matrix composites10.1016/j.matdes.2015.02.003 ↗
65. Comparison between current models for the strength of particulate-reinforced metal matrix nanocomposites with emphasis on consideration of Hall-Petch effect [J]10.1016/j.msea.2011.10.043 ↗
66. Experimental investigation and simulation of precipitation evolution in Mg-3Nd-0.2Zn alloy [J]10.1016/j.calphad.2017.11.006 ↗
67. Microstructurally inhomogeneous composites: is a homogeneous reinforcement distribution optimal10.1016/j.pmatsci.2015.01.002 ↗