Modification of Cu-deficient CaCu2.8Ti4O12 ceramics via Mg2+ substitution at Cu sites for improved dielectric properties and thermal stability
Source abstract
Abstract
Mg 2+ substitution at the Cu sites of Cu-deficient CaCu 2.8-xMg xTi 4O 12 ( x = 0.00, 0.05, and 0.10) ceramics was accomplished using a polymer pyrolysis technique. The nonlinear and dielectric properties of all ceramics under various sintering temperatures were investigated. Very low tanδ ∼ 0.011–0.030 and giant ε′ ∼ 4406–13,521 were obtained in these ceramics. Surprisingly, excellent thermal stability, where ε′ remained within± 15% and is adequate for X8R capacitors, is obtained in CaCu 2.75Mg 0.05Ti 4O 12 and CaCu 2.7Mg 0.1Ti 4O 12 ceramics sintered at 1100 °C for 8 h. Additionally, the nonlinear J-E properties were improved compared to an unmodified sample. Interestingly, a nonlinear coefficient (α) of ∼ 58.05 in the CaCu 2.75Mg 0.05Ti 4O 12 ceramic sintered at 1100 °C for 8 h is acceptable for varistor applications. Improvement of nonlinear and dielectric properties arise from the electrical interface responses altered by Mg 2+ substitution. The ceramics were characterized using XRD, TEM and FE-SEM techniques to investigate their crystal structure and microstructure. EDXS results confirmed the coexistence of TiO 2 and CaTiO 3 phases in all ceramics. It was suggested that the enhancement of grain boundary resistance ( R gb) with simultaneously improved electrical and nonlinear J-E behaviors caused by the alternation of electrical interface responses at GBs. XPS measurements of these ceramics presented Cu 3+/Cu 2+/Cu + ratios that indicate the semiconducting properties of grains.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Dielectric properties of ceramics · Ferroelectric and Piezoelectric Materials · Microwave Dielectric Ceramics Synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (68)
Show source-provided references
1. The abnormal multiple dielectric relaxation responses of Al3+ and Nb5+ co-doped rutile TiO2 ceramics10.1016/j.jallcom.2020.157891 ↗
2. Colossal permittivity of (Gd + Nb) co-doped TiO2 ceramics induced by interface effects and defect cluster10.1016/j.ceramint.2020.11.012 ↗
3. High thermal stability and excellent dielectric properties of a novel X8R-type CdCu3Ti4O12 ceramics through a sol-gel technique10.1016/j.materresbull.2017.09.040 ↗
4. Grain engineering inducing high energy storage in CdCu3Ti4O12 ceramics10.1016/j.ceramint.2020.02.239 ↗
5. Microwave absorption study of composites based on CQD@BaTiO3 core shell and BaFe12O19 nanoparticles10.1016/j.jallcom.2020.157411 ↗
6. Structure, optical, and radiation shielding properties of PVA–BaTiO3 nanocomposite films: an experimental investigation10.1016/j.radphyschem.2020.109281 ↗
7. Giant dielectric response in (Nb + Zn) co-doped strontium titanate ceramics tailored by atmosphere10.1016/j.scriptamat.2019.05.034 ↗
8. Colossal dielectric permittivity in co-doping SrTiO3 ceramics by Nb and Mg10.1016/j.ceramint.2020.05.174 ↗
9. Highly sensitive multiparametric luminescent thermometer for biologically-relevant temperatures based on Mn4+, Ln3+ co-doped SrTiO3 nanocrystals10.1016/j.jallcom.2021.159973 ↗
10. Investigation of dielectric and electrochemical behavior of CaCu3−xMnxTi4O12 (x = 0, 1) ceramic synthesized through semi-wet route10.1016/j.matchemphys.2020.122804 ↗
11. Thermal stability improvement of dielectric properties and non-ohmic characteristic of CaCu3+xTi4O12 ceramics via a Cu-nonstoichiometric approach10.1016/j.ceramint.2021.05.126 ↗
12. Colossal dielectric response and relaxation behavior in novel system of Zr4+ and Nb5+ co-substituted CaCu3Ti4O12 ceramics10.1016/j.ceramint.2020.08.113 ↗
13. Dielectric and non-ohmic analysis of Sr2+ influences on CaCu3Ti4O12-based ceramic composites10.1016/j.materresbull.2020.111071 ↗
14. Tunable photoluminescence of CaCu3Ti4O12 based ceramics modified with tungsten10.1016/j.jallcom.2020.156652 ↗
15. Preparation and characterization of Mg2+-doped CaCu3Ti4O12 pigment with high NIR reflectance10.1016/j.ceramint.2020.06.324 ↗
16. Enhancement of breakdown electric field and dielectric properties of CaCu3Ti4O12 ceramics by Sr doping10.1016/j.matchemphys.2020.122722 ↗
17. Very high-performance dielectric and non-ohmic properties of novel X8R type Ca1-1.5xHoxCu3Ti4O12/TiO2 ceramics10.1016/j.jallcom.2018.11.298 ↗
18. Very high temperature stability and excellent dielectric properties of a novel X9R-type Ca1−xSrxCu3Ti4O12/TiO2 nanocomposite synthesized by a polymer pyrolysis technique10.1016/j.apsusc.2019.01.214 ↗
19. Origin of high dielectric performance in fine grain-sized CaCu3Ti4O12 materials10.1016/j.jeurceramsoc.2019.12.042 ↗
20. Ultra-high dielectric tuning performance and double-set resistive switching effect achieved on the Bi2NiMnO6 thin film prepared by sol–gel method10.1016/j.jcis.2021.08.109 ↗
21. Effects of Mg2+ doping ions on giant dielectric properties and electrical responses of Na1/2Y1/2Cu3Ti4O12 ceramics10.1016/j.ceramint.2016.07.167 ↗
22. Linear-like lead-free relaxor antiferroelectric (Bi0.5Na0.5)TiO3–NaNbO3 with giant energy-storage density/efficiency and super stability against temperature and frequency10.1039/C8TA12232F ↗
23. Frequency and temperature independent (Nb0.5Ga0.5)x(Ti0.9Zr0.1)1−xO2 ceramics with giant dielectric permittivity and low loss10.1016/j.ceramint.2019.09.292 ↗
24. Origin of colossal permittivity and low dielectric loss in Na1/3Cd1/3Y1/3Cu3Ti4O12 ceramics10.1016/j.ceramint.2020.01.136 ↗
25. Enhancement of giant dielectric response in CaCu3Ti4O12 ceramics by Zn substitution10.1111/j.1551-2916.2009.03384.x ↗
26. Mixed-valent structure, dielectric properties and defect chemistry of Ca1−3x/2TbxCu3Ti4−xTbxO12 ceramics10.1016/j.ceramint.2017.03.191 ↗
27. Effect of sintering temperature and Sm3+ doping on the dielectric properties and non-Ohmic behavior of Ca1-1.5xSmxCu3Ti4.2O12 (x = 0.05 and 0.10) ceramics10.1016/j.rinp.2021.104896 ↗
28. Effect of Mn doping on the temperature-dependent anomalous giant dielectric behavior of CaCu3Ti4O1210.1103/PhysRevB.85.245210 ↗
29. Improved dielectric and nonlinear properties of CaCu3Ti4O12 ceramics with Cu-rich phase at grain boundary layers10.1016/j.ceramint.2019.04.247 ↗
30. Improvement in varistor properties of CaCu3Ti4O12 ceramics by chromium addition10.1016/j.jmst.2019.08.055 ↗
31. Structural and dielectric properties, and nonlinear electrical response of the CaCu3−xZnxTi4O12 ceramics: experimental and computational studies10.1016/j.ceramint.2021.04.248 ↗
32. Tunable capacitor-varistor response of CaCu3Ti4O12/CaTiO3 ceramic composites with SnO2 addition10.1016/j.matchar.2020.110699 ↗
33. An engineering design based on nano/micro-sized composite for CaTiO3/CaCu3Ti4O12 materials and its dielectric and non-Ohmic properties10.1016/j.ceramint.2019.07.166 ↗
34. High permittivity, low dielectric loss, and high electrostatic potential barrier in Ca2Cu2Ti4O12 ceramics10.1016/j.matlet.2012.02.054 ↗
35. Very high performance dielectric and non-Ohmics properties of CaCu3Ti4.2O12 ceramics for X8R capacitors10.1016/j.ceramint.2018.04.156 ↗
36. A novel strategy to enhance dielectric performance and non-Ohmic properties in Ca2Cu2−xMgxTi4O1210.1016/j.jeurceramsoc.2014.04.037 ↗
37. Electrical properties and microstructural characteristics of nonstoichiometric CaCu3xTi4O12 ceramics10.1016/j.jallcom.2008.02.042 ↗
38. Effect of phase purity on dielectric properties of CaCu3+xTi4O12 ceramics10.1016/j.solidstatesciences.2013.07.006 ↗
39. Humidity sensitive properties of pure and Mg-doped CaCu3Ti4O1210.1016/j.snb.2010.03.063 ↗
40. Microstructure and enhanced dielectric response in Mg doped CaCu3Ti4O12 ceramics10.1016/j.jallcom.2015.12.143 ↗
41. Electrical properties of Ni-doped CaCu3Ti4O12 ceramics10.1016/j.ssi.2021.115633 ↗
42. A facile polymer-pyrolysis preparation of submicrometer CoMoO4 as an electrode of lithium ion batteries and supercapacitors10.1016/j.ceramint.2021.01.023 ↗
43. Enhanced electrochemical performance of Mg-doped LiCoO2 synthesized by a polymer-pyrolysis method10.1016/j.ceramint.2014.03.170 ↗
44. Comparative studies of pure, Sr-doped, Ni-doped and co-doped CaCu3Ti4O12 ceramics: enhancement of dielectric properties10.1016/j.jallcom.2017.05.053 ↗
45. Temperature stability of the dielectric properties of Zr4+-doped CaCu3Ti4.2O12 ceramics for X9R capacitor applications10.1016/j.jallcom.2019.03.111 ↗
46. Grain size effects on the dielectric properties of CaCu3Ti4O12 ceramics for supercapacitor applications10.1016/j.ceramint.2015.04.109 ↗
47. Very low loss tangent and giant dielectric properties of CaCu3Ti4O12ceramics prepared by the sol–gel process10.1007/s10854-017-7377-5 ↗
48. Enhanced giant dielectric response in Mg-substituted CaCu3Ti4O12 ceramics10.1016/j.ssc.2008.12.016 ↗
49. Influence of processing conditions on the electrical properties of CaCu3Ti4O12 ceramics10.1111/j.1551-2916.2006.01184.x ↗
50. Very high thermal stability with excellent dielectric, and non-ohmics properties of Mg-doped CaCu3Ti4.2O12 ceramics10.1007/s10854-018-9381-9 ↗
51. R values in analysis of powder diffraction data using Rietveld refinement10.1107/S0021889893012348 ↗
52. High dielectric constant in ACu3Ti4O12 and ACu3Ti3FeO12 phases10.1006/jssc.2000.8703 ↗
53. Fabrication of miniaturized high bandwidth dielectric resonator on patch (DRoP) antenna using high dielectric CaCu3Ti4O12 nanoparticles10.1016/j.jallcom.2018.03.015 ↗
54. Phase structure, microstructure and broadband dielectric response of Cu nonstoichiometry CaCu3Ti4O12 ceramic10.1016/j.jallcom.2016.04.318 ↗
55. Electromagnetic interference (EMI) shielding, microwave absorption, and optical sensing properties of BaM/CCTO composites in Ku-band10.1016/j.rinp.2019.102307 ↗
56. New approach for synthesis of nano-sized CaCu3Ti4O12 powder by economic and innovative method10.1007/s10854-020-03490-9 ↗
57. Enhanced electrical behavior in Ca1−xSrxCu3Ti4O12 ceramics10.1016/j.ceramint.2019.04.141 ↗
58. Simultaneous two-step enhanced permittivity and reduced loss tangent in Mg/Ge-Doped CaCu3Ti4O12 ceramics10.1016/j.jallcom.2021.160322 ↗
59. Very low loss tangent, high dielectric and non-ohmic properties of Ca1−1.5xPrxCu3Ti4O12 ceramics prepared by the sol–gel process10.1007/s10854-017-7850-1 ↗
60. Varistor ceramics10.1111/j.1151-2916.1999.tb01793.x ↗
61. Ultra-stable X9R type CaCu3−xZnxTi4.1O12 ceramics10.1016/j.ceramint.2018.08.072 ↗
62. Interface control and modification of band alignment and electrical properties of HfTiO/GaAs gate stacks by nitrogen incorporation10.1039/C4TC00572D ↗
63. Modulating the interface quality and electrical properties of HfTiO/InGaAs gate stack by atomic-layer-deposition-derived Al2O3 passivation layer10.1021/am506351u ↗
64. Passivation of Ge surface treated with trimethylaluminum and investigation of electrical properties of HfTiO/Ge gate stacks10.1016/j.jmst.2017.04.021 ↗
65. Microstructure optimization and optical and interfacial properties modulation of sputtering-derived HfO2 thin films by TiO2 incorporation10.1016/j.jallcom.2014.05.074 ↗
66. Evaluation of the effect of the stoichiometric ratio of Ca/Cu on the electrical and microstructural properties of the CaCu3Ti4O12 polycrystalline system10.1088/0022-3727/42/18/185503 ↗
67. A novel approach to achieve high dielectric permittivity and low loss tangent in CaCu3Ti4O12 ceramics by co-doping with Sm3+ and Mg2+ ions10.1016/j.jeurceramsoc.2015.06.008 ↗
68. Effects of sintering temperature on the internal barrier layer capacitor (IBLC) structure in CaCu3Ti4O12(CCTO) ceramics10.1016/j.jeurceramsoc.2012.03.040 ↗