journal article·2022-03

Microstructural and mechanical properties of NiCoCrAlSi high entropy alloy fabricated by mechanical alloying and spark plasma sintering

Armita Shahbazkhan, Hamed Sabet, Mehrdad Abbasi

Publisher page

Abstract

Abstract In this study, the microstructural and mechanical properties of NiCoCrAlSi high entropy alloy (HEA) fabricated by mechanical alloying and spark plasma sintering (SPS) method was studied. Initially, the starting powders with the composition of Ni28Co26Cr26Al10Si10 were subjected to mechanical milling at different times of 5, 10, 15, 20 and 40 hours. The 40 h milled powder was then sintered by SPS method at 1170 °C. The microstructural characterization, phase analysis and mechanical properties of this sample were evaluated by field emission scanning electron microscopy (FESEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), Rietveld analysis and tensile test. XRD results showed that by increasing the milling time the size of crystallites reduced and lattice strain increased. In addition, formation of FCC1 (F1) phase at final stages of mechanical alloying was observed. However, the peak of some of the remaining elements was still observed after 40 hours of milling. After sintering, formation of FCC2 (F2) phase alongside F1 was observed. According to quantitative analysis, F1 phase with fraction of 89.3 wt.% and F2 phase with fraction of 10.7 wt.% is formed after SPS process. For this sample, a tensile strength of 1365±141 MPa was obtained.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Entropy Alloys Studies · High-Temperature Coating Behaviors · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. High-entropy alloys10.1038/s41578-019-0121-4 ↗
2. High-entropy alloys: a critical review10.1080/21663831.2014.912690 ↗
3. Gao · 2016
4. Murty · 2019
5. Mechanical alloying and milling10.1016/S0079-6425(99)00010-9 ↗
6. El-Eskandarany MS. Mechanical Alloying: For Fabrication of Advanced Engineering Materials, Univ. Press of Mississippi, 2013.
7. Varalakshmi S. Synthesis and Characterization of Nanocrystalline High Entropy Alloys by Mechanical Alloying 2008.10.1016/j.jallcom.2007.05.104 ↗
8. Alloying behavior of binary to octonary alloys based on Cu–Ni–Al–Co–Cr–Fe–Ti–Mo during mechanical alloying10.1016/j.jallcom.2008.10.111 ↗
9. Nanocrystalline CoCrFeNiCuAl high-entropy solid solution synthesized by mechanical alloying10.1016/j.jallcom.2009.05.144 ↗
10. Alloying behavior in multi-component AlCoCrCuFe and NiCoCrCuFe high entropy alloys10.1016/j.msea.2011.11.044 ↗
11. Effect of W and Zr on structural, thermal and magnetic properties of AlCoCrCuFeNi high entropy alloy10.1016/j.jallcom.2012.12.095 ↗
12. Mechanical properties and stacking fault energies of NiFeCrCoMn high-entropy alloy10.1007/s11837-013-0771-4 ↗
13. Influence of Ti addition and sintering method on microstructure and mechanical behavior of a medium-entropy Al0. 6CoNiFe alloy10.1016/j.msea.2014.09.077 ↗
14. Rapid preparation of AlCoCrFeNi high entropy alloy by spark plasma sintering from elemental powder mixture10.1016/j.matlet.2016.06.014 ↗
15. Spark plasma sintering of high entropy alloys
16. Fabrication of (TixZr1− x) B2-(ZrxTi1− x) N composites by reactive spark plasma sintering of ZrB2-TiN10.1016/j.jallcom.2021.161403 ↗
17. Effects of 211 and 413 ordering on the corrosion behavior of V-Al-C MAX phases prepared by spark plasma sintering10.1016/j.jeurceramsoc.2021.03.001 ↗
18. Influence of milling time on structural and microstructural parameters of Ni50Ti50 prepared by mechanical alloying using Rietveld analysis10.1155/2018/2560641 ↗
19. Phase formation in mechanically alloyed Al xCoCrCuFeNi (x = 0.45, 1, 2.5, 5 mol) high entropy alloys10.1016/j.intermet.2012.08.015 ↗
20. Effect of co addition on microstructural and mechanical properties of WC-B4C-SiC composites10.1016/j.ceramint.2021.02.149 ↗