Fabrication and characterization of an Al-based nanocomposite with high specific strength and good elongation using large amount CMA nanoparticles
Source abstract
Abstract
Abstract In the present research, preparation and characterization of both powder and bulk of a new Al-CMA nanocomposite were investigated. For this, the composites were prepared by mechanical alloying/milling (MA/MM) of 10 wt % Al3Mg2 and pure Al mix powders and then cold pressing, sintering and finally hot extrusion. According to the microscopic observations, a uniform distribution of Al3Mg2 in the Al and a clean interface between them were obtained after ball milling. In addition, analysis of particle size distribution revealed that the presence of Al3Mg2 particles and amount of process control agent had a significant influence on the composite powder refinement. In addition, the measured Carr index of 13.5% indicated that the ball milled powder offered good flowability. High-resolution microscopic studies showed that formation of twins might be one of the crystallite size decreasing mechanisms during MA/MM process. The initial powder boundary in the powder samples could not be completely deleted by cold pressing and sintering, but could be reduced by following hot extrusion. The microstructure of extruded nanocomposites comprised nanometer Al grains and Al3Mg2 nanoparticles dispersed interior grains which produced by dynamic recrystallizations (DRX). The Al3Mg2 particles experienced vigorous size reduction during MA/MM, which play an important role in Al grain refining during DRX via Zener pinning. These conditions along with clean interface for the 15 h milled sample could be resulted in notable enhancement of 515% in yield strength (YS), 603% in ultimate compressive strength (UCS), 181% in young’s modulus and 406% in microhardness compared with pure Al. A more interesting point was the elongation up to 24% owing to the uniform distribution of nanoparticles in Al grains. These results from Al–Al3Mg2 nanocomposites discover newer feasibilities for impressive manufacturing of high strength and low-density composites with improved ductility, which could make them possible candidates for a wide range of industries especially for weight critical applications.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. Microstructure and mechanical properties of Al matrix nanocomposites reinforced by different amounts of CNT and SiCW10.1016/j.compositesb.2019.107081 ↗
2. Novel Al-matrix nanocomposites reinforced with multi-walled carbon nanotubes10.1016/j.jallcom.2006.10.146 ↗
3. Enhanced performance of nano-sized SiC reinforced Al metal matrix nanocomposites synthesized through microwave sintering and hot extrusion techniques10.1016/j.pnsc.2017.08.015 ↗
4. Chawla · 2006
5. CNT reinforced aluminium matrix composite-a review
6. The influence of nickel coating on the wettability of aluminum on ceramics10.1016/S1359-835X(02)00161-6 ↗
7. Preparation of coatings on alumina ceramic for wettability10.1016/j.ceramint.2013.11.002 ↗
8. Shiqin Yang Interface structure and strength of ultrasonic vibration liquid phase bonded joints of Al2O3p/6061Al composites10.1016/j.scriptamat.2005.06.009 ↗
9. 2011
10. Complex metallic alloys as new materials for additive manufacturing10.1088/1468-6996/15/2/024802 ↗
11. Powder metal matrix composites: selection and processing10.1016/S0921-5093(97)00829-0 ↗
12. Novel nanoparticle-reinforced metal matrix composites with enhanced mechanical properties10.1002/adem.200700106 ↗
13. Mechanical alloying and milling10.1016/S0079-6425(99)00010-9 ↗
14. Grain size stabilization and strengthening of cryomilled nanostructured Cu 12at% Al alloy10.1016/j.jallcom.2017.05.093 ↗
15. Flowability of moist pharmaceutical powders10.1016/j.powtec.2008.06.017 ↗
16. Yadroitsev · 2009
17. The elastic properties, elastic models and elastic perspectives of metallic glasses10.1016/j.pmatsci.2011.07.001 ↗
18. Preparation of MoSi2–Al2O3 nano-composite via MASHS route10.1016/j.ijrmhm.2011.11.005 ↗
19. Mechanochemical reduction of MoO3 powder by Al and Si to synthesize nanocrystalline MoSi2
20. The microstructural revolution of Al-10%Al3Mg2 nanocomposite during mechanical milling
21. Mechanochemical reduction of MoO3 powder by silicone to synthesize nanocrystalline MoSi210.4028/www.scientific.net/AMR.264-265.1364 ↗
22. Effects of nanosized TiCp dispersion on the high-temperature tensile strength and ductility of in situ TiCp/Al-Cu-Mg-Si nanocomposites10.1016/j.jallcom.2018.10.052 ↗
23. Effects of TiN nanoparticles on hot deformation behavior of ultra-fine grained Al2024-TiN nanocomposites prepared by spark plasma sintering10.1016/j.mechmat.2019.103152 ↗
24. Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite10.1016/j.jallcom.2019.03.065 ↗
25. Influence of high B4C contents on structural evolution of Al-B4C nanocomposite powders produced by high energy ball milling10.1016/j.ceramint.2018.11.247 ↗
26. Effect of milling time on morphology and microstructure of Al-Mg/Al2O3 nanocomposite powder produced by mechanical alloying
27. Particle-reinforced metal matrix nanocomposites fabricated by selective laser melting: a state of the art review10.1016/j.pmatsci.2019.04.006 ↗
28. A novel aluminum based nanocomposite with high strength and good ductility10.1016/j.jallcom.2015.07.088 ↗
29. Wear behavior of Al/CMA-type Al3Mg2 nanocomposites fabricated by mechanical milling and hot extrusion10.1080/10402004.2015.1050138 ↗
30. NasserAl-Aqeeli, Mechanically alloyed nanocomposites10.1016/j.pmatsci.2012.10.001 ↗
31. Fabrication of titanium carbide nano-powders by a very high speed planetary ball milling with a help of process control agents10.1016/j.powtec.2015.01.047 ↗
32. Low temperature synthesis of carbon nanotube-reinforced aluminum metal composite powders using cryogenic milling10.1557/jmr.2014.300 ↗
33. Effect of tensile strain rate on high-temperature deformation and fracture of rolled Al- 15 vol.%B4C composite10.1016/j.msea.2019.02.016 ↗
34. Nanostructure formation by mechanical attrition10.1016/0965-9773(95)00027-5 ↗
35. A dislocation model for the minimum grain size obtainable by milling10.1016/S1359-6454(03)00230-1 ↗
36. Formation of nanostructure in Al produced by a low-energy ball milling at cryogenic temperature10.1016/j.msea.2003.10.235 ↗
37. An-Ping Ye, Fabrication and mechanical properties of high-performance aluminum alloy10.1007/s12598-014-0262-y ↗
38. Extrusion and high-temperature deformation of fibre-reinforced aluminium10.1016/0266-3538(89)90092-4 ↗
39. Pinning effect of spheroid second-phase particles on grain growth studied by three-dimensional phase-field simulations10.1016/j.commatsci.2010.05.020 ↗
40. Grain refinement in copper under large strain deformation10.1080/01418610108216659 ↗
41. Highly parallel computer simulations of particle pinning10.1016/S1359-6462(00)00354-7 ↗
42. Dieter · 1976
43. Processing and properties of magnesium containing a dense uniform dispersion of nanoparticles10.1038/nature16445 ↗
44. Effect of reinforcement content and aging treatment on microstructure and mechanical behavior of B4Cp/6061Al composites10.1016/j.msea.2018.12.042 ↗
45. Effect of heat treatment on microstructure and mechanical properties of Al 2024 matrix composites reinforced with Ni60Nb40 metallic glass particles10.1016/j.jallcom.2019.151732 ↗