Effect of Zr on microstructure and hot cracking susceptibility of ZGH451 superalloy fabricated by direct energy deposition
Source abstract
Abstract
Four groups of newly developed Ni-based superalloy samples with different Zr contents were manufactured by Direct energy deposition (DED). This study focuses on the influence of Zr element concentration on microstructure and cracking formation mechanism in DED-processed Ni-based superalloy ZGH451. Although Zr content is low, it strongly affects the formation of the precipitated phase and hot tearing tendency. Measurement of the crack area showed that the crack density value increases with the Zr concentration. According to thermodynamic simulation results and microstructures observed, Zr microsegregation in the interdendritic regions and considerable amounts of Zr is present in oxides or carbides. Zr contributes to forming large-size carbides mainly due to zirconia providing nucleation sites and the dissolution of Zr. Simultaneously, the solidification has been retarded due to the continuous accumulation of large Zr atoms, which increases the γ-γ′ eutectic fraction. Moreover, Zr addition could effectively decrease the solidus temperature of ZGH451 alloys, leading to the critical liquid film at the end of solidification. Based on these results, staying below 0.05 wt% of Zr content to reduce the risk of hot tearing in additive manufacturing superalloy was proposed.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (52)
Show source-provided references
1. Experimental study on weld formation of Inconel 718 with fiber laser welding under reduced ambient pressure10.1016/j.vacuum.2018.02.008 ↗
2. A coupled thermal, fluid flow, and solidification model for the processing of single-crystal alloy CMSX-4 through scanning laser epitaxy for turbine engine hot-section component repair (Part I10.1007/s11663-014-0117-9 ↗
3. Physical metallurgy of the nickel-based superalloys10.1016/B978-0-444-53770-6.00022-8 ↗
4. Microstructure of selective laser melted CM247LC nickel-based superalloy and its evolution through heat treatment10.1016/j.matchar.2016.02.004 ↗
5. A review of laser fabrication of metallic engineering components and of materials10.1179/174328407X179593 ↗
6. Single-crystal turbine blade tip repair by laser cladding and remelting10.1016/j.cirpj.2017.04.001 ↗
7. Additive manufacturing of Ni-based superalloys: residual stress, mechanisms of crack formation and strategies for crack inhibition
8. Crack initiation mechanism of laser powder bed fusion additive manufactured Al-Zn-Mg-Cu alloy10.1016/j.matchar.2022.112415 ↗
9. Fatigue crack growth in additively manufactured Hastelloy X - Influences of crack orientation and post-fabrication treatments10.1016/j.msea.2022.143773 ↗
10. Misorientation-dependent solute enrichment at interfaces and its contribution to defect formation mechanisms during laser additive manufacturing of superalloys
11. Dendritic microstructure and hot cracking of laser additive manufactured Inconel 718 under improved base cooling10.1016/j.jallcom.2016.01.250 ↗
12. Direct laser metal deposition of Inconel 73810.1016/j.msea.2018.10.020 ↗
13. Alloys-by-design: application to new superalloys for additive manufacturing10.1016/j.actamat.2020.09.023 ↗
14. The influence of the laser scan strategy on grain structure and cracking behaviour in SLM powder-bed fabricated nickel superalloy10.1016/j.jallcom.2014.06.172 ↗
15. High-entropy intermetallic compound with ultra-high strength and thermal stability10.1016/j.scriptamat.2020.113674 ↗
16. Investigations on the microstructure and crack formation of IN738LC samples processed by selective laser melting using Gaussian and doughnut profiles10.1016/j.matdes.2015.10.027 ↗
17. Fractal scan strategies for selective laser melting of 'unweldable' nickel superalloys
18. Effect of minor alloying elements on crack-formation characteristics of Hastelloy-X manufactured by selective laser melting
19. Effect of B, Zr, and C on hot tearing of a directionally solidified nickel-based superalloy10.1007/s11661-016-3416-8 ↗
20. Selective laser melting of IN738 superalloy with a low Mn+Si content: Effect of energy input on characteristics of molten pool, metallurgical defects, microstructures and mechanical properties10.1016/j.msea.2021.141985 ↗
21. The effect of Hf on solidification cracking inhibition of IN738LC processed by Selective Laser Melting10.1016/j.msea.2021.140733 ↗
22. Roles of Zr and Y in cast microstructure of M951 nickel-based superalloy10.1016/S1003-6326(11)61361-7 ↗
23. On the role of Zr and B addition on solidification cracking of IN738LC produced by laser powder bed fusion10.1016/j.mtla.2022.101609 ↗
24. Effect of Zr and B on castability of Ni-based superalloy IN79210.1007/s11661-004-0308-0 ↗
25. Effect of Hf and Zr contents on stress-rupture and fatigue crack growth rate performances in FGH96 PM superalloy10.1016/S1006-706X(14)60059-5 ↗
26. On the role of boron, carbon and zirconium on hot cracking and creep resistance of an additively manufactured polycrystalline superalloy10.1016/j.mtla.2021.101193 ↗
27. Hot tearing in polycrystalline Ni-based IN738LC superalloy: Influence of Zr content10.1016/j.jmatprotec.2013.10.001 ↗
28. Effect of Zr content on formability, microstructure and mechanical properties of selective laser melted Zr modified Al-4.24Cu-1.97Mg-0.56Mn alloys10.1016/j.jallcom.2018.06.032 ↗
29. Influence of Zr content on the incipient melting behavior and stress-rupture life of CM247 LC nickel base superalloy10.1016/j.jallcom.2015.07.104 ↗
30. Effects of Boron and Zirconium on Grain Boundary Morphology and Creep Resistance in Nickel-Based Superalloy10.1007/s11665-019-04419-y ↗
31. Stress rupture embrittlement in cast Ni-based superalloy 62510.1016/j.msea.2020.139811 ↗
32. Effect of zirconium on microstructure and mechanical properties of cast fine-grain CM 247 LC superalloy10.2320/matertrans.45.554 ↗
33. The study of the wear mechanism of titanium carbide coated carbide tools10.1016/0020-7357(79)90011-8 ↗
34. Influence of minor alloying element additions on the crack susceptibility of a nickel based superalloy manufactured by LPBF10.3390/ma14195702 ↗
35. Solid-state reaction for ZrC formation in a Zr-doped nickel-based superalloy10.1016/0036-9748(86)90493-X ↗
36. Effect of grain-boundary characteristics on castability of nickel-base superalloys10.1007/s11661-004-0018-7 ↗
37. Revealing the true partitioning character of zirconium in additively manufactured polycrystalline superalloys
38. Phosphorous behavior and its effect on secondary phase formation in high refractory content powder-processed Ni-based superalloys10.1016/j.mtla.2019.100423 ↗
39. Oxidation assisted recrystallization and cracking at grain boundaries in Nimonic 80 A during elevated temperature service10.1016/j.corsci.2022.110452 ↗
40. The effect of boron and zirconium on the microcracking susceptibility of IN-738LC derivatives in laser powder bed fusion10.1016/j.apsusc.2021.151541 ↗
41. Effect of Zr content on crack formation and mechanical properties of IN738LC processed by selective laser melting10.1016/S1003-6326(21)65582-6 ↗
42. The crystal growth, intercellular spacing and microsegregation of selective laser melted Inconel 718 superalloy10.1016/j.vacuum.2018.10.074 ↗
43. Laser powder bed fusion of compositionally graded CoCrMo-Inconel 718
44. The initiation and propagation mechanism of the overlapping zone cracking during laser solid forming of IN-738LC superalloy10.1016/j.jallcom.2018.03.366 ↗
45. A generalised hot cracking criterion for nickel-based superalloys additively manufactured by electron beam melting
46. Effect of Zr on solidification and microstructure of a Ni-based superalloy with high Al and Ti contents10.1007/s41230-022-1058-6 ↗
47. Effect of Zr on solidification segregation behavior of K417G alloy and its anomalous effect during rapid cooling process10.1016/j.jallcom.2020.155243 ↗
48. Analysis of liquation and solidification cracks in the electron beam welding of GTD-111 nickel-base superalloy joint10.1088/2053-1591/ac1007 ↗
49. Causes analysis on cracks in nickel-based single crystal superalloy fabricated by laser powder deposition additive manufacturing10.1016/j.matdes.2018.10.042 ↗
50. Mechanical behavior of laser powder bed fusion processed inconel 625 alloy10.1007/s41403-021-00269-0 ↗
51. Mechanical behavior and dynamic strain ageing in Haynes®282 superalloy subjected to accelerated ageing10.1016/j.msea.2021.142486 ↗
52. Effect of ageing on microstructure, mechanical properties and creep behavior of alloy 740H10.1007/s11661-020-05951-6 ↗