journal article·2022-07

Densification and microstructure formation mechanisms of 80 W-14Ni-6Fe fabricated by laser powder bed fusion

Han Ye, Yibin Huang, Chao Wei, Yaliang Liu

Publisher page

Abstract

Tungsten heavy alloys (WHAs) are typically refractory alloy, and machining tungsten alloy components at room temperature is a challenge. Currently, Laser additive manufacturing (LAM) provides a feasible route for machining complex tungsten alloy parts. In this study, the high relative density and almost defect-free 80 W-14Ni-6Fe specimens were successfully obtained via using laser powder bed fusion (LPBF). The densification, microstructure formation mechanisms and tensile properties of LPBFed tungsten alloy were systematically investigated. The results revealed that the relative density of tungsten alloy increases and then decreases with the laser energy density increases. Nearly full densification 80 W-Ni-Fe alloys were obtained when the volumetric energy density (VED) was 80–100 J/mm 3 . The typical microstructure contained irregular tungsten grain consolidation, W dendrites, spherical tungsten particles and Ni-Fe bonding phase, which was due to melting of partial tungsten particles during LPBF. Interestingly, many ultra-fine crystals occurred in the Ni-Fe matrix, which was closely related to the rapid heat and cooling during LPBF. Besides, there were two strengthening mechanisms in LPBFed 80 W alloy, respectively solid solution strengthening and dispersion strengthening. Hence, the 80 W-Ni-Fe alloy with optimum process parameters exhibited high tensile strength, and the ultimate tensile strength (UTS) reached 1064MP. This work will aid in the additive manufacturing of refractory metal alloys with excellent properties and expand the application prospects of tungsten alloys.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · High Entropy Alloys Studies · Additive Manufacturing Materials and Processes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. Effect of deuterium retention upon sputtering yield of tungsten by deuterons10.1016/j.jnucmat.2010.08.057 ↗
2. Investigation on sintering mechanism of nanoscale tungsten powder based on atomistic simulation10.1016/j.actamat.2010.03.033 ↗
3. Some structural effects of plastic deformation on tungsten heavy metal alloys10.1016/S0921-5093(00)01369-1 ↗
4. Deformation characteristic of the 93W-4.9Ni-2.1Fe tungsten heavy alloy deformed by hydrostatic extrusion10.1016/j.msea.2006.07.134 ↗
5. Fabrication and properties of mechanically alloyed oxide-dispersed tungsten heavy alloys10.1016/S0921-5093(03)00641-5 ↗
6. Fabrication of ultrafine-grain and great-performance W-Ni-Fe alloy with medium W content10.1016/j.jallcom.2020.156237 ↗
7. On the remarkable fracture toughness of 90 to 97W-NiFe alloys revealing powerful new ductile phase toughening mechanisms10.1016/j.actamat.2020.01.012 ↗
8. Fabrication, characterization, and mechanical properties of 93W–4.9Ni–2.1Fe/95W–2.8Ni–1.2Fe–1Al2O3 heavy alloy composites10.1016/j.msea.2015.04.026 ↗
9. Effects of processing parameters on densification behavior, microstructure evolution and mechanical properties of W–Ti alloy fabricated by laser powder bed fusion10.1016/j.msea.2021.142177 ↗
10. Single crystalline-like crystallographic texture formation of pure tungsten through laser powder bed fusion10.1016/j.scriptamat.2021.114252 ↗
11. Microstructural and mechanical approaches of the selective laser melting process applied to a nickel-base superalloy10.1016/j.msea.2011.11.092 ↗
12. Solidification pattern, microstructure and texture development in Laser Powder Bed Fusion (LPBF) of Al10SiMg alloy10.1016/j.matchar.2018.08.025 ↗
13. Hierarchical microstructure and enhanced mechanical properties of SLM-fabricated GH5188 Co-superalloy10.1016/j.msea.2021.142276 ↗
14. Effect of process parameters on the Selective Laser Melting (SLM) of tungsten10.1016/j.ijrmhm.2017.11.035 ↗
15. High-density tungsten fabricated by selective laser melting: densification, microstructure, mechanical and thermal performance10.1016/j.optlastec.2019.03.018 ↗
16. Analysis of laser-induced microcracking in tungsten under additive manufacturing conditions: experiment and simulation10.1016/j.actamat.2020.04.060 ↗
17. Selective laser melting additive manufacturing of tungsten with niobium alloying: microstructure and suppression mechanism of microcracks10.1016/j.jallcom.2021.159879 ↗
18. Pure tungsten and oxide dispersion strengthened tungsten manufactured by selective laser melting: microstructure and cracking mechanism
19. Effect of processing parameters on microstructure and properties of tungsten heavy alloys fabricated by SLM10.1016/j.ijrmhm.2019.03.020 ↗
20. Microstructure and mechanical properties of additive manufactured W-Ni-Fe-Co composite produced by selective laser melting10.1016/j.ijrmhm.2019.105111 ↗
21. Selective laser melting of W-Ni-Cu composite powder: densification, microstructure evolution and nano-crystalline formation10.1016/j.ijrmhm.2017.09.004 ↗
22. Microstructure and fracture behavior of 90W–7Ni-3Fe alloy fabricated by laser directed energy deposition10.1016/j.jallcom.2021.158975 ↗
23. Ternary W-Ni-Fe tungsten heavy alloys: a first principles and experimental investigations10.1016/j.ijrmhm.2018.03.011 ↗
24. Effect of processing parameters on microstructure and mechanical properties of 90W–6Ni–4Mn heavy alloy10.1016/j.ijrmhm.2014.09.024 ↗
25. Influence of microelement Hf on microstructure, mechanical properties and shielding effect of W-Ni-Fe alloy10.1016/j.jallcom.2017.07.037 ↗
26. Densification behaviour, microstructural characteristics and mechanical properties of liquid phase sintered W-2Ni-1Fe alloy10.1016/j.jallcom.2019.152897 ↗
27. Effect of alloying addition and microstructural parameters on mechanical properties of 93% tungsten heavy alloys10.1016/j.msea.2015.05.046 ↗
28. Microstructure and strengthening mechanisms of 90We7Nie3Fe alloys prepared using laser melting deposition10.1016/j.jallcom.2020.155545 ↗
29. 93W–5.6Ni–1.4Fe heavy alloys with enhanced performance prepared by cyclic spark plasma sintering10.1016/j.msea.2014.01.089 ↗
30. Tensile mechanical properties and fracture behavior of tungsten heavy alloys at 25–1100 °C10.1016/j.msea.2015.08.079 ↗
31. Determination of melt pool dimensions using DOE-FEM and RSM with process window during SLM of Ti6Al4V powder10.1016/j.optlastec.2018.01.013 ↗
32. Interplay between single phase solid solution strengthening and multi-phase strengthening in the same high entropy alloy10.1016/j.msea.2019.138620 ↗
33. Plastic thermal deformation behavior and microstructure evolution of solid solution strengthened Ni-based superalloy10.1016/j.msea.2021.141533 ↗
34. Solid solution strengthening mechanism in high pressure die casting Al–Ce–Mg alloys10.1016/j.msea.2021.141109 ↗
35. High-throughput solid solution strengthening characterization in high entropy alloys10.1016/j.actamat.2019.01.029 ↗
36. Fabrication and mechanical properties of WC nanoparticle dispersion-strengthened copper10.1016/j.msea.2021.141274 ↗