Solution combustion assisted synthesis of ultra-magnetically soft LiZnTiMn ferrite ceramics
Source abstract
Abstract
Abstract Wide practical application and increasing functional requirements for high-frequency ceramics lead to the active search for novel multicomponent ferrites and their synthesis technique. In this paper, a solution-combustion-assisted approach was proposed and realized for the successful production of ultra-magnetically soft LiZnTiMn-ferrite ceramics with advanced electromagnetic performance. Preceramic nanopowders of Li0.28Zn0.16Ti0.41Mn0.10Fe2.05O4 with spinel structure were synthesized via glycine-nitrate combustion at variable Ox/Red ratios (φ = 0.5, 1.0 and 1.5) followed by stabilizing quenching (600 °C, 2 h) and vibrating mill grinding. LiZnTiMn-ferrite-based fine ceramics were produced then using PVA binding (1 wt %), isostatic pressing (400 МPа) and Bi2O3-assisted (0.3 wt %) isothermal sintering (980 °C, 8 h) techniques. As result, a series of LiZnTiMn-ferrite ceramic samples were obtained and their structure was examined in detail using XRD, SEM, EDXS, AAS and ASA methods. It was shown that the Ox/Red ratio of the initial reaction solution is an efficient parameter affecting both crystallite size (26-38 nm) /crystallinity degree (up to 91%) of preceramic LiZnTiMn-ferrite powders and grain size (2.7-9.8 µm) / grain size distribution of resulting fine ceramics. Based on the results of vibration magnetometry it was found that ceramics samples possess the ultra-magnetically soft behavior with Hc = 0.61-0.89 Oe, Mr = 3.62-5.13 emu/g and Ms = 67.23-78.70 emu/g depending on the initial Ox/Red ratio. Besides, results of resonator analysis (100 Hz - 1000 kHz) demonstrate that the dielectric constant of the samples strongly depends on the average grain size and reaches its maximum value (~ 6.4⸱10-4) at 100 Hz for the stoichiometric Ox/Red ratio (φ = 1.0) of reagents, wherein the linewidths of ferromagnetic resonance and resonance of spin waves practically unchanged and are in ranges of 327-344 and 1.43-1.45 Oe, respectively. Thus, it was found that the solution combustion synthesis, adapted for fine ceramics production, provides controlling morphological and structural parameters of the pre-ceramic powders through Ox/Red ratio of initial reagents and as consequence, allows variable magnetic and dielectric characteristics of the resulting ceramic products. Developed ceramic materials can be promising for use as a basis for modern radio-electronic devices of both civil and military use.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnetic Properties and Synthesis of Ferrites · Electromagnetic wave absorption materials · Multiferroics and related materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (75)
Show source-provided references
1. Development of magneto-dielectric materials based on Li-ferrite ceramics10.1016/j.jallcom.2007.05.050 ↗
2. Microwave Lithium Ferrites
3. Electrical and magnetic properties of ZrO2-doped lithium-titanium-zinc ferrite ceramics10.1016/j.ceramint.2019.06.282 ↗
4. Effect of the Red/Ox ratio on the structure and magnetic behavior of Li0.5Fe2.5O4 nanocrystals synthesized by solution combustion approach10.22226/2410-3535-2019-4-475-479 ↗
5. The effect of Sr substitution on electrical, dielectric and magnetic behavior of lithium ferrite10.1016/j.ceramint.2019.04.040 ↗
6. Low-frequency dielectric behavior of lithium-zinc ferrites10.1002/pssa.2211340124 ↗
7. Synergy effects between Li0.42Zn0.27Ti0.11Fe2.2O4 nanoparticles and CuO-Bi2O3 mixtures in low-temperature sintered LiZnTi ferrites with enhanced gyromagnetic and microwave dielectric properties10.1016/j.jallcom.2020.156806 ↗
8. Low coercivity microwave ceramics based on LiZnMn ferrite synthesized via glycine-nitrate combustion10.17586/2220-8054-2019-10-3-313-317 ↗
9. Ferrite-piezoelectric heterostructures for microwave and millimeter devices: recent advances and future possibilities10.2497/jjspm.61.S25 ↗
10. Modern microwave ferrites10.1109/TMAG.2011.2180732 ↗
11. Study of LiTiMg-ferrite radome for the application of satellite communication10.1016/j.jmmm.2010.03.032 ↗
12. Goldman · 2006
13. Synthesis and properties of magnetic fluids produced on the basis of magnetite particles10.1134/S1070427216050025 ↗
14. Investigation of grain growth and magnetic properties of low-sintered LiZnTi ferrite-ceramic10.1016/j.ceramint.2020.02.268 ↗
15. Microstructure and microwave magnetic properties of low-firring Li0.42Zn0.27Ti0.11Mn0.1Fe2.1O4 ferrite10.1088/1757-899X/322/2/022053 ↗
16. Remarkable influence on the dielectric and magnetic properties of lithium ferrite by Ti and Zn substitution10.1016/j.ssc.2009.06.010 ↗
17. Investigation on Ti4+ substitution LiZn ferrite with FMR linewidth at Ku band
18. Influence of LZN nanoparticles on microstructure and magnetic properties of bi-substituted LiZnTi low-sintering temperature ferrites10.1016/j.ceramint.2018.10.087 ↗
19. Structural and some magnetic properties of manganese-substituted lithium ferrites10.1016/j.jmmm.2012.05.056 ↗
20. Dielectric properties of nanocrystalline Zn-doped lithium ferrites synthesized by microwave-induced glycine-nitrate process10.1007/s10948-015-3225-0 ↗
21. Impact of Co and Mn substitution on structural and dielectric properties of lithium soft ferrites10.1016/j.physb.2019.05.014 ↗
22. Synthesis of Ni0.4Zn0.6Fe2O4 spinel ferrite and microwave adsorption of related polymer composite10.17586/2220-8054-2020-11-5-595-600 ↗
23. The influence of ZrO2 additive on sintering and microstructure of lithium and lithium-titanium-zinc ferrites10.1016/j.ceramint.2018.09.061 ↗
24. Improving the magnetic properties of Li-Zn-Ti ferrite by doping with H3BO3-Bi2O3-SiO2-ZnO glass for LTCC technology10.1007/s11664-014-3279-y ↗
25. Hysteresis and initial permeability behavior of vanadium-substituted lithium-zinc-titanium ferrite10.1016/j.physb.2004.06.059 ↗
26. Effect of Mn3+ doping on the loss of Li0.37Zn0.26Ti0.12Fe2.37O4 ferrite10.1088/2053-1591/abc6cf ↗
27. Effects of sintering temperature and Bi2O3 content on microstructure and magnetic properties of LiZn ferrites10.1016/j.jmmm.2007.10.016 ↗
28. Effects of iron deficiency content on electromagnetic performance of LiZn ferrites10.1007/s10948-017-3975-y ↗
29. The past, present, and future of ferrites10.1111/j.1551-2916.1999.tb20058.x ↗
30. Technological scheme for lithium-substituted ferrite production under complex high-energy impact10.1016/j.nimb.2020.04.026 ↗
31. I.F. Cruz C. Freire J.P. Araujo C. Pereira A.M. Pereira Multifunctional ferrite nanoparticles: from current trends toward the future J.M. Barandiaran R.L. Hadimani Magnetic Nano structured Materials. Chapter 3.
32. A comprehensive study on thermal stability and magnetic properties of MnZn-ferrite nanoparticles10.1016/j.jmmm.2018.11.052 ↗
33. Nanomaterials for high-frequency device and photocatalytic applications: Mg-Zn-Ni ferrites10.1016/j.jallcom.2018.02.287 ↗
34. Mechanochemical synthesis of MnZn ferrite nanoparticles suitable for biocompatible ferrofluids10.1016/j.ceramint.2015.09.103 ↗
35. Characterization of crystalline structure of ball-milled nano-Ni-Zn-ferrite by Rietveld method10.1016/j.matchemphys.2003.08.012 ↗
36. Prenucleation formations in control over synthesis of CoFe2O4 nanocrystalline powders10.1134/S107042721606001X ↗
37. Optimization of the synthesis of copper ferrite nanoparticles by a polymer-assisted sol-gel method10.1021/acsomega.9b02295 ↗
38. Impact of sonochemical condition on the structure and physical properties of MnFe2O4 spinel ferrite nanoparticles
39. Magnetically recoverable catalyst based on porous nanocrystalline HoFeO3 for process of n-hexane conversion10.1016/j.apt.2019.10.033 ↗
40. The effect of contact non-equilibrium plasma on structural and magnetic properties of MnxFe3−xO4 spinels10.1186/s11671-017-2268-5 ↗
41. Synthesis of magnetic ferrite nanoparticles with high hyperthermia performance via a controlled co-precipitation method10.3390/nano9081176 ↗
42. Electromagnetic properties of LTCC-ferrite in the microwave range10.1051/epjap/2018180226 ↗
43. LTCC processed CoTi substituted M-type barium ferrite composite with BBSZ glass powder additives for microwave device applications
44. Solution combustion synthesis of nanoscale materials10.1021/acs.chemrev.6b00279 ↗
45. Magnetic and electrical properties of Mn-Zn ferrites synthesized by combustion method without subsequent heat treatments10.1063/1.3560880 ↗
46. Single-step solution-combustion synthesis of magnetically soft NiFe2O4 nanopowders with controllable parameters10.3103/S1061386219040101 ↗
47. Magnetic properties of Li0.5Fe2.5O4 nanoparticles synthesized by solution combustion method10.1007/s00339-017-1304-8 ↗
48. High antibacterial and photocatalytic activity of solution combustion synthesized Ni0.5Zn0.5Fe2O4 nanoparticles: effect of fuel to oxidizer ratio and complex fuels10.1016/j.ceramint.2019.06.159 ↗
49. Ni0.4Zn0.6Fe2O4 nanopowders by solution-combustion synthesis: influence of Red/Ox ratio on their morphology, structure, and magnetic properties10.3103/S106138622004007X ↗
50. Solution combustion synthesis, characterization, magnetic, and dielectric properties of CoFe2O4 and Co0.5M0.5Fe2O4 (M = Mn, Ni, and Zn)10.1039/D0CP03161E ↗
51. NdFeO3 nanocrystals under glycine nitrate combustion formation10.1016/j.jcrysgro.2017.03.022 ↗
52. Facile combustion synthesis of TbFeO3 nanocrystals with hexagonal and orthorhombic structure10.17586/2220-8054-2019-10-6-694-700 ↗
53. Effect of ignition temperature and fuel amount on photocatalytic activity of solution combustion synthesized ZnO10.1016/j.ceramint.2020.05.324 ↗
54. Synthesis of Al2O3, MgO and MgAl2O4 by solution combustion method and investigation of performance in partial oxidation of methane10.1016/j.powtec.2019.10.001 ↗
55. Solution combustion synthesis of bioceramic calcium phosphates by single and mixed fuels – a comparative study10.1016/j.ceramint.2007.03.009 ↗
56. Combustion synthesis of cobalt ferrite nanoparticles – influence of fuel to oxidizer ratio10.1016/j.jallcom.2011.10.094 ↗
57. Sol-gel auto-combustion synthesis of spinel-type ferrite nanomaterials10.1007/s11706-012-0167-3 ↗
58. The effect of fuel type in synthesis of NiFe2O4 nanoparticles by microwave-assisted combustion method10.1088/1742-6596/707/1/012046 ↗
59. Sol-gel auto combustion synthesis and characterization of cobalt ferrite nanoparticles: different fuels approach10.1016/j.mseb.2019.114388 ↗
60. Combustion synthesis: effect of urea on the reaction and characteristics of Ni-Zn ferrite powder10.1023/A:1016356623401 ↗
61. Composition, microstructure, and electrical properties control of the powders synthesized by sol-gel auto-combustion method using citric acid as the fuel10.1186/s11671-017-1976-1 ↗
62. SCS-assisted production of EuFeO3 core-shell nanoparticles: formation process, structural features and magnetic behavior
63. Grain size effect on the dielectric and magnetic properties of NiFe2O4 ceramics10.1016/j.physe.2011.06.014 ↗
64. Dielectric and magnetic properties of nickel ferrite ceramics using crystalline powders derived from DL alanine fuel in sol-gel combustion10.1016/j.ceramint.2015.03.014 ↗
65. A novel and simple process for nanosized Mg-Mn ferrite preparation from solution combustion method and study of its characteristics10.1111/ijac.12066 ↗
66. Nickel ferrite ceramics: combustion synthesis, sintering, characterization, and magnetic and electrical properties10.1080/21870764.2021.1907031 ↗
67. Impedance spectroscopic studies on NiFe2O4 with different morphologies: microstructure vs dielectric properties10.1016/j.ceramint.2012.08.078 ↗
68. Novel approaches to solution-combustion synthesis of nanomaterials10.3103/S1061386207010049 ↗
69. Combustion synthesis of advanced materials: principles and applications10.1016/S0065-2377(08)60093-9 ↗
70. Effect of sintering temperature on the synthesis of LiZnMnFe microwave ceramics with controllable electro/magnetic properties10.1016/j.ceramint.2021.07.183 ↗
71. Pre-ceramic nanostructured LiZnMn-ferrite powders: synthesis, structure, and electromagnetic properties10.1007/s10717-020-00274-9 ↗
72. Preparation and magnetic properties of titanium-substituted LiZn ferrites via a sol-gel auto-combustion process10.1016/S0955-2219(02)00082-1 ↗
73. Combustion synthesis, structure and magnetic properties of Li-Zn ferrite ceramic powders10.1016/j.ceramint.2017.07.213 ↗
74. Impact of grain size and structural changes on magnetic, dielectric, impedance and modulus spectroscopic characteristics of CoFe2O4 nanoparticles synthesized by honey mediated sol-gel auto-combustion method10.1088/2043-6254/aa853a ↗
75. Synthesis of nanocrystalline HoFeO3 photocatalyst via heat treatment of products of glycine-nitrate combustion10.1134/S1070363218120022 ↗