journal article·2022-01

Investigation of mechanical properties and corrosion resistance of fine-grained aluminum alloys Al-Zn with reduced zinc content

V.N. Chuvil'deev, A.V. Nokhrin, V.I. Kopylov, M.Yu. Gryaznov, S.V. Shotin, C.V. Likhnitskii, N.A. Kozlova, Ya.S. Shadrina, N.N. Berendeev, N.V. Melekhin, G.S. Nagicheva, K.E. Smetanina, N.Yu. Tabachkova

Publisher page

Abstract

Abstract Mechanical properties of fine-grained Al-(1, 2, 3)%Zn alloys obtained by Equal Channel Angle Pressing were studied. The recrystallization activation energy was found to decrease with increasing Zn content. The Hall-Petch coefficient for the Al-Zn alloys was found to change nonmonotonously during annealing. An increased Zn concentration at the grain boundaries was shown to result in altering the creep and superplasticity mechanisms of the Al-Zn alloys. The corrosion rate of the Al-Zn alloys was found to depend on the annealing temperature nonmonotonously. The corrosion rate in the Al-(2,3)%Zn alloy was shown to decreasing down to 8–9 mm/year with increasing the annealing temperature up to 200 оC. The increasing of the annealing temperature up to 300 оC leads to the increasing of the corrosion rate up to 11.4–11.9 mm/year. The obtained results were analyzed on the base of a concept of solid phase wetting of the grain boundaries in the Al by Zn. The effect of solid state wetting of the grains boundaries was shown to allow explaining majority of anomalia observed in the Al-Zn alloys: (i) the effect of the reduction of the recrystallization activation energy; (ii) the effect of a non-monotonous variation of the Hall-Petch coefficient during annealing; (iii) an increasing of plasticity of the Al-Zn alloys in the creep regime, etc. In order to describe the anomalia in the corrosion resistance of the Al-Zn alloys, one should also take into account a nonuniform Zn distribution in the specimens.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (61)

Show source-provided references
1. Aluminum Alloys – Contemporary Research and Application · 1989
2. Elagin · 1982
3. Advanced high-strength aluminum-base materials10.1007/s11041-005-0066-7 ↗
4. Structure-properties correlation in Al 7050 and Al 7055 high-strength aluminum alloys10.1016/j.msea.2007.05.116 ↗
5. Recent advances in ageing of 7xxx series aluminum alloys: a physical metallurgy10.1016/j.jallcom.2018.11.286 ↗
6. Heat treatment of 7xxx series aluminum alloys – some recent developments10.1016/S1003-6326(14)63306-9 ↗
7. Recently-developed aluminum solutions for aerospace applications10.4028/www.scientific.net/MSF.519-521.1271 ↗
8. Trends in aluminum alloy development and their joining methods
9. Influence of predeformation on the ageing in an Al-Zn-Mg alloy – I. Microstructure evolution and mechanical properties10.1016/S1359-6454(98)00293-6 ↗
10. Decomposition processes in Al-Zn-Mg alloys10.1007/BF00541825 ↗
11. The nucleation of precipitates: the system Al-Zn-Mg10.1016/0001-6160(65)90067-2 ↗
12. GP-zones in Al-Zn-Mg alloys and their role in artificial aging10.1016/S1359-6454(01)00251-8 ↗
13. HREM study and structure modeling of the η’ phase, the hardening precipitates in commercial Al-Zn-Mg alloys10.1016/S1359-6454(99)00138-X ↗
14. Influence of alloy composition and heat treatment on precipitate composition in Al-Zn-Mg-Cu alloys10.1016/j.actamat.2009.09.003 ↗
15. V.S. Sinyavskiy, V.D. Val’kov, V.D. Kalinin, Corrosion and protection of the aluminum alloys. Moscow, Metallurgiya, 1986, (in Russian).
16. The effect of RRA on the strength and SCC resistance on AA7050 and AA7150 aluminum alloys10.1016/j.msea.2004.02.052 ↗
17. Principles of equal-channel angular pressing as a processing tool for grain refinement10.1016/j.pmatsci.2006.02.003 ↗
18. Scale up and application of equal-channel angular extrusion for the electronics and aerospace industries10.1016/j.msea.2007.04.133 ↗
19. Semi-continuous equal-channel angular extrusion and rolling of AA5083 and AZ31 alloys10.3390/met9101035 ↗
20. Creep behavior of solid solutioned and annealed Al-7075 alloy processed by equal channel angular pressing10.1016/j.msea.2019.138225 ↗
21. Influence of grain coarsening on the creep parameters during the superplastic deformation of a severely Friction Stir Processed Al-Zn-Mg-Cu alloy10.1007/s11661-017-4198-3 ↗
22. Fatigue life of fine-grain Al-Mg-Sc alloys produced by equal-channel angular pressing10.1016/S0921-5093(02)00813-4 ↗
23. Overview of fatigue properties of fine grain 5056 Al-Mg alloy processed by equal-channel angular pressing10.1016/S0921-5093(00)01682-8 ↗
24. High strain rate superplasticity in Al-Zn-Mg-based alloy: microstructural design, deformation behavior, and modeling10.3390/ma13092098 ↗
25. Comparison between superplastic deformation mechanisms at primary and steady stages of the fine grain AA7475 aluminum alloy10.1016/j.msea.2018.01.102 ↗
26. Mechanical behavior of ultrafine-grained Al-5Zn, Al-10Zn, Al-30Zn alloys
27. Erratum: Borderud SP, Li Y, Burkhalter JE, Sheffer CE and Ostroff JS. Electronic cigarette use among patients with cancer: Characteristics of electronic cigarette users and their smoking cessation outcomes. Cancer. doi: 10.1002/ cncr.2881110.1002/cncr.29118 ↗
28. Influence of equal-channel angular pressing on precipitation in an Al-Zn-Mg-Cu alloy10.1016/j.actamat.2009.03.017 ↗
29. Microstructures and mechanical properties of ultrafine grained 7075 Al alloy processed by ECAP and their evolutions during annealing10.1016/j.actamat.2004.06.017 ↗
30. Formation of nanograined structure and decomposition of supersaturated solid solution during high pressure torsion of Al-Zn and Al-Mg alloys10.1016/j.actamat.2004.06.006 ↗
31. Softening of nanostructured Al-Zn and Al-Mg alloys after severe plastic deformation10.1016/j.actamat.2006.04.025 ↗
32. Grain boundary complexions and phase transformations in Al- and Cu-based alloys10.3390/met9010010 ↗
33. Ultrafine grained structures resulting from SPD-induced phase transformation in Al-Zn alloy10.1002/adem.201500151 ↗
34. Precipitation phenomena in an ultrafine-grained Al alloy10.1016/j.actamat.2012.12.037 ↗
35. Gradual softening of Al-Zn alloys during high pressure torsion10.1016/j.matlet.2012.06.026 ↗
36. Thermal evolution and grain boundary phase transformations in severely deformed nanograined Al-Zn alloys10.1016/j.actamat.2008.08.021 ↗
37. The effect of severe plastic deformation on precipitation in supersaturated Al-Zn-Mg alloys10.1016/j.msea.2007.01.001 ↗
38. Inversed solid-phase grain boundary wetting in the Al-Zn system10.1007/s10853-011-5322-1 ↗
39. Pseudopartial wetting of grain boundaries in severely deformed Al-Zn alloys10.3103/S1067821215010198 ↗
40. Effect of the wetting of grain boundaries on the formation of a solid solution in the Al-Zn system10.1134/S0021364012180063 ↗
41. Wetting of grain boundaries by the second solid state phase in Al-based alloys10.3103/S1062873813110166 ↗
42. “Wetting” phase transitions by the second solid phase for linear defects (Grain boundary triple junctions)10.1134/S0021364020160031 ↗
43. Unusual super-ductility at room temperature in an ultrafine-grained aluminum alloy10.1007/s10853-010-4588-z ↗
44. Influence of fine scale features on room temperature superplastic behaviour of an ultrafine-grained Al-30Zn alloy10.1016/j.matlet.2019.07.097 ↗
45. Equal-channel angular extrusion (ECAE): from a laboratory curiosity to an industrial technology10.3390/met10020244 ↗
46. Review: modes and processes of severe plastic deformation10.3390/ma11071175 ↗
47. Segal · 2010
48. Impact of mechanical activation on sintering kinetics and mechanical properties of ultrafine-grained 95W-Ni-Fe tungsten heavy alloys10.1016/j.jallcom.2018.09.176 ↗
49. Aluminum: Properties and Physical Metallurgy. Ed. J.E. Hatch. Publisher: Aluminum Association Inc. and ASM International, 1984.
50. S.S. Gorelik, S.V. Dobatkin, L.M. Kaputkina, Recrystallization of the Metals and Alloys. Moscow, MISiS, 2005 (in Russian).
51. Effect of Small Impurity Concentrations on the diffusive properties of grain boundaries
52. Effect of recovery and recrystallization on the Hall-Petch relation parameters in submicrocrystalline metals: II. Model for calculating the Hall-Petch relation parameters10.1134/S0036029518050051 ↗
53. Effect of recovery and recrystallization on the Hall-Petch relation parameters in submicrocrystalline metals: I. Experimental studies10.1134/S0036029518010044 ↗
54. Current and potential measurements along simulated cracks10.1016/0010-938X(84)90060-X ↗
55. Predictive approaches to stress corrosion cracking failure10.1016/0010-938X(80)90128-6 ↗
56. Environmental conditions in simulated stress corrosion cracks involving sensitized stainless steels in a chloride solution10.1016/0010-938X(92)90056-9 ↗
57. Various electrochemical measurements in a simulated corrosion fatigue crack10.5006/1.3584971 ↗
58. Stress and temperature dependence of stress relaxation ageing behaviour of an Al-Zn-Mg alloy10.1016/j.msea.2019.138859 ↗
59. Nieh · 1997
60. The theory of structural superplasticity: I. The physical nature of the superplasticity phenomenon10.1016/0956-7151(92)90065-M ↗
61. A model for boundary diffusion controlled creep in polycrystalline materials10.1063/1.1702656 ↗