journal article·2022-01

Effect of Invar particle size on microstructures and properties of the Cu/Invar bi-metal matrix composites fabricated by SPS

Qiangqiang Nie, Guohong Chen, Bing Wang, Lei Yang, Jianhua Zhang, Wenming Tang

Publisher page

Abstract

Abstract The Cu/Invar bi-metal matrix composites have a great potential to be used as novel electronic packaging materials. In order to clarify effects of the Invar particle size on microstructures and properties of the composites, two Invar powders of average sizes of 26 µm and 105 µm were employed to fabricated the 50 wt% Cu/Invar composites, respectively, by spark plasma sintering (SPS) at 700–800 °C under vacuum condition with a heating rate of 100 °C/min, a pressure of 50 MPa and a holding time of 1 min. The results indicate that the Cu/ fine Invar (f-Invar) composites have finer Cu grain sizes in which the f-Invar particles are semi-continuously distributed. The composites have typical characteristics of low-angle Cu grain boundaries, high-density Σ3 growth twins and Cu/Invar coherent/semi-coherent interface. On the contrary, the coarse Invar (c-Invar) particles are discontinuously distributed in the Cu/c-Invar composites, resulting in the formation of coarser Cu grain sizes, high-angle Cu grain boundaries and non-coherent Cu/Invar interface. Moreover, compared with the f-Invar particles, the c-Invar ones can not only effectively decrease the Cu/Invar interfacial area, but also prohibit the Cu/Invar interface diffusion, therefore considerably improve thermal conductivity (TC) of the Cu/Invar composites at the cost of a little reduction of tensile strength (Rm). It is also clarified that properties of the Cu/Invar composites are sensitive to the sintering temperature. The 700 °C sintered 50 wt% Cu/c-Invar composite has the highest TC of 130.1 W/(m·K). It is very close to the theoretical value predicted by the Maxwell model and much superior to the TCs previously reported in the Cu/Invar composites of the similar Invar fraction.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Electronic Packaging and Soldering Technologies · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. Copper matrix thermal conductive composites with low thermal expansion for electronic packaging10.1016/j.ceramint.2020.04.117 ↗
2. Power electronic modules
3. High thermal conductive Cu-diamond composites synthesized by electrodeposition and the critical effects of additives on void-free composites10.1016/j.ceramint.2019.06.215 ↗
4. Fabrication of ultrafine W-Cu composite powders and its sintering behavior10.1016/j.jmrt.2019.12.046 ↗
5. Sintering behavior and properties of Mo-Cu composites10.1155/2018/8703986 ↗
6. Critical effect and enhanced thermal conductivity of Cu-diamond composites reinforced with various diamond prepared by composite electroplating10.1016/j.ceramint.2019.04.008 ↗
7. Effect of spark plasma sintering and high-pressure torsion on the microstructural and mechanical properties of a Cu-SiC composite
8. Fabrication and characterization of Cu-B4C metal matrix composite by powder metallurgy: Effect of B4C on microstructure, mechanical properties and electrical conductivity10.1007/s12666-018-1518-2 ↗
9. Ultraprecise thermal expansion measurements of seven low expansion materials10.1364/AO.15.002344 ↗
10. Controlling the coefficient of thermal expansion of printed wiring board using copper-Invar-copper foil
11. Cu-containing Fe-Ni corrosion-resistant alloys designed by a cluster-based stable solid solution model10.1007/s11661-011-0913-7 ↗
12. Atomic mobilities, zero-flux planes and flux reversals in fcc Cu−Fe−Ni alloys10.1016/j.calphad.2011.04.006 ↗
13. Invar effect in fcc-FeCu solid solutions
14. Microstructures and thermophysical properties of Cu-Fe64Ni32Co4 alloys, Rare Metal
15. Effects of rolling and annealing on microstructures and properties of Cu/Invar electronic packaging composites prepared by powder metallurgy10.1016/S1003-6326(15)63808-0 ↗
16. Microstructures and properties of the 40Cu/Ag(Invar) composites fabricated by powder metallurgy and subsequent thermo-mechanical treatment10.1007/s11661-018-4548-9 ↗
17. Q.Q. Nie , G.H. Chen , B. Wang , L. Yang , W.M. Tang , Process optimization, microstructures and mechanical/thermal properties of the Cu/Invar bi-metal matrix composites fabricated by spark plasma sintering, T. Nonferr. Metal. Soc. To be published. https://kns.cnki.net/kcms/detail/43.1239.tg.20210825.1706.006.html.
18. An investigation of the effect of SiC particle size on Cu-SiC composites
19. Thermal properties of diamond/copper composite material10.1016/S0026-2714(03)00215-4 ↗
20. Effect of particle size on the microstructures and mechanical properties of SiC-reinforced pure aluminum composites10.1007/s11665-010-9801-3 ↗
21. The thermal expansion coefficient as a key design parameter for thermoelectric materials and its relationship to processing-dependent bloating10.1007/s10853-013-7421-7 ↗
22. Matweb , Material properties data. http://www.matweb.com/search/DataSheet.aspx?MatGUID=b6fb00b235f0442da4d31a0cd04671c9, 2021 (Accessed 25 June 2021).
23. Sodium borohydride reduction of aqueous silver-iron-nickel Solutions: a chemical route to synthesis of low thermal expansion-high conductivity Ag-Invar alloys10.1007/s11661-009-9859-4 ↗
24. Interdiffusion and kirkendall-effect in the Fe-Ni-Cu system10.4028/www.scientific.net/SSP.72.117 ↗
25. Martensitic transformation in ultrafine Fe-Ni powders10.1016/0921-5093(90)90154-U ↗
26. Thermodynamics of sintering, in woodhead publishing series in metals and surface engineering
27. Microstructures and tensile mechanical properties of consolidated copper10.1590/1516-1439.027715 ↗
28. Trost · 1982 · 654
29. Bonding strength of Invar/Cu clad strips fabricated by twin-roll casting process10.1016/S1003-6326(18)64892-7 ↗
30. Field-assisted sintering technology/spark plasma sintering: mechanisms, materials, and technology developments10.1002/adem.201300409 ↗
31. Interface design in 3D-SiC/Al-Si-Mg interpenetrating composite fabricated by pressureless infiltration10.1016/j.ceramint.2018.03.016 ↗
32. Invar-type nanocrystalline compacts obtained by spark plasma sintering from mechanically alloyed powders10.1007/s10853-017-1771-5 ↗
33. Estimation of the thermal conductivity of composites10.1023/A:1004674308487 ↗
34. Strength of deformation processed Cu-Fe-Ag in situ composites10.1016/j.matlet.2006.06.030 ↗
35. Numerical and experimental research on fluid flow, solidification and bonding strength during the twin-roll casting of Cu/Invar/Cu clad strips10.1007/s11663-020-01854-4 ↗
36. The enhanced range of temperature for coefficient of low thermal expansion, electrical and thermal conductivities of Cu substituted Fe-Ni invar alloys10.1088/0031-8949/91/3/035701 ↗
37. S. Jha , Cuvar-A new controlled expansion, high conductivity material for electronic thermal management, Proc. 45th Electron. Comp. Technol. Conf., Las Vegas, 1995, 542–547. https://doi.org/10.1109/ECTC.1995.515336.10.1109/ECTC.1995.515336 ↗
38. Designing low-thermal-expansivity, high-conductivity alloys in the Cu-Fe-Ni ternary system10.1007/s11837-998-0132-x ↗