journal article·2022-01

Study on microstructure and mechanical properties of single crystal/powder superalloy pulsed current diffusion bonded joints

Boxian Zhang, Chunhuan Chen, Zelun Cai, Hao Tian, Jinbao Hou, Lu Chai, Yanlong Lv, Jianchao He

Publisher page

Abstract

Abstract To optimize the overall structure design of the aero-engine turbine disks, the study of pulsed current diffusion bonding on the second generation nickel-based single-crystal superalloy DD5 and the third generation powder superalloy FGH98 was performed, and high-quality joints were obtained after post-welding heat treatment(PWHT). The microstructure and element diffusion were analyzed by using SEM and EDS, and the microhardness and room / high temperature tensile strength were analyzed. It can be seen from the results that with the pulse current, the diffusion bonding produced a high-temperature gradient from the interface to the base metal, which protected the base metal. The precipitation phase of γ′ phase within the connection interface near the FGH98 side within 200 µm exhibits very small granular-large-size unstable petals-larger granular similar to the base metal. The γ′ phase in DD5 grows abnormally at the interface. Large granular γ′ enhancement phases occurred on the FGH98 side after heat treatment with no significant changes on the DD5 side. The microhardness of the joints is not less than 400HV; and from DD5 side to FGH98 side, the hardness decreases first and then increases. The average tensile strength of the joints at room temperature is 1078 MPa, which is 99% of the tensile strength of the base metal with low performance. The average tensile strength of joints at high temperature (650 °C) is 1089 MPa, which is equivalent to the strength of the base metal.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Intermetallics and Advanced Alloy Properties · High Temperature Alloys and Creep · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Topology optimization in aircraft and aerospace structures design10.1007/s11831-015-9151-2 ↗
2. Application requirements and challenges of CMC-SiC composites on aero-engine
3. W. Liu , Research progress on key manufacturing technology of aeroengine blades. (21), 2016, 50–56. (in Chinese).
4. Creep behavior and a deformation mechanism based creep rate model under high temperature and low stress condition for single crystal superalloy DD510.1016/j.msea.2020.139414 ↗
5. Mechanical behavior of a DD5 single crystal superalloy with different misorientations under quasi-static and dynamic compression10.1557/jmr.2018.251 ↗
6. Microstructure and mechanical properties of the brazed region in the AlCoCrFeNi high-entropy alloy and FGH98 superalloy joint10.1016/j.msea.2020.140714 ↗
7. Effect of Ta on the microstructure of high performance Ni-based powder metallurgy superalloys10.1007/s11431-018-9351-9 ↗
8. Joint properties of electron beam welding of IC10/GH3039 with different beam displacement
9. Microstructure and mechanical properties of DD5 single crystal superalloy brazing joint
10. Effect of heat treatment on microstructure and property of DD6/FGH96 linear friction welded joint
11. Research on application of hot isostatic pressing technology in the field of nickel-based casting superalloys
12. Research progress of influence factor of transient liquid phase diffusion bonding of nickel-based single crystal superalloy
13. Microstructure and mechanical properties of Ti-48Al-2Cr-2Nb alloy joints produced by transient liquid phase bonding using spark plasma sintering10.1016/j.matchar.2018.10.024 ↗
14. Diffusion bonding between TZM alloy and WRe alloy by spark plasma sintering10.1016/j.jallcom.2018.06.111 ↗
15. Diffusion welding of powder metallurgy high speed steel by spark plasma sintering10.1016/j.jmatprotec.2019.116383 ↗
16. Microstructure characteristic and its influence on the strength of SiC ceramic joints diffusion bonded by spark plasma sintering10.1016/j.ceramint.2017.11.185 ↗
17. Analysis of grain-and particle-size distributions in metallic materials10.1179/095066072790137729 ↗
18. Effect of pre-strain on microstructural evolution during thermal exposure of single crystal superalloy CMSX-410.1016/S1003-6326(11)60855-8 ↗
19. Effect of solution heat treatment on the microstructure and properties of a novel nickel-based P/M superalloy FGH98I
20. Effect of solution and aging temperature on microstructure and properties of a new powder superalloy
21. D.D. Krueger , R.D. Kissinger , R.G. Menzies , Development and introduction of a damage tolerant high temperature turbine Nickel-base disk alloy,Rene88DT, in: Superalloys 1992: Proceedings of the 7th International Symposium on Superalloys, Seven Springs, PA: TMS, 1992, pp. 277–286.10.7449/1992/Superalloys_1992_277_286 ↗
22. The kinetics for the hydrogen absorption and desorption processes of hydrogen storage alloys: a review
23. Microstructure analysis on extruded nickel-based powder superalloy
24. Coarsening kinetics of cubic γ′ precipitates of a nickel-based single crystal superalloy after long-term aging
25. Topologically close packed phases in an experimental rhenium-containing single crystal superalloy
26. The influence of matrix stacking fault energy on creep deformation modes in γ’ precipitation-hardened nickel-base alloys10.1007/BF02917575 ↗
27. Microstructure and stress-rupture property of TLP diffusion bonded DD3 single crystal superalloy jionts
28. Microstructure evolution of single-crystal superalloy DD6 at high-temperature
29. K. Song , S. Zhu , K. Fang , L. Lv , Z. Qing , Z. Zhong , Z. Zhu , Research on SPS diffusion bonding technology of 5A06 aluminum alloy and thermal, electric and force field coupling simulation, Welding Branch of China Mechanical Engineering Society, China, 2020. (in Chinese).
30. Effects of microstructure on high temperature dwell fatigue crack growth in a coarse grain PM nickel based superalloy10.1016/j.actamat.2015.02.023 ↗
31. Effect of cooling rate and resulting microstructure on tensile properties and deformation mechanisms of an advanced PM nickel-based superalloy10.1016/j.jallcom.2019.07.221 ↗
32. Research on in-situ heating and stretching of the third generation nickel-based single crystal superalloy