Dynamic Strength of VT6 Titanium Alloy Manufactured by Laser Metal Deposition
Source abstract
Abstract
In the present paper, we study strength anisotropy of VT6 titanium alloy additively manufactured by laser metal deposition. The Hugoniot elastic limit and spall strength of the alloy are measured depending on the direction of deposition, the ratio of primary and secondary powders, and preliminary heat treatment. The measurements are performed by recording and analyzing full wave profiles under shock compression at the amplitude 10 GPa. The additively manufactured titanium alloy demonstrates strength isotropy, and its strength characteristics are slightly higher than those of conventionally manufactured industrial specimens. The concentration of secondary powder during additive manufacturing also exerts no effect on strength properties of the alloy, both under static and dynamic loads.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Nuclear Materials and Properties · Fusion materials and technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. Frazier, W.E., Metal Additive Manufacturing: A Review, J. Mater. Eng. Perf., 2014, vol. 23, pp. 1917–1928. https://doi.org/10.1007/s11665-014-0958-z10.1007/s11665-014-0958-z ↗
2. Sames, W.J., List, F.A., Pannala, S., DeHoff, R.R., and Babu, S.S., The Metallurgy and Processing Science of Metal Additive Manufacturing, Int. Mater. Rev., 2016, vol. 61, pp. 315–360. https://doi.org/10.1080/09506608.2015.111664910.1080/09506608.2015.1116649 ↗
3. Seifi, M., Salem, A., Beuth, J., Harrysson, O., and Lewandowski, J.J., Overview of Materials Qualification Needs of Metal Additive Manufacturing, JOM, 2016, vol. 68, pp. 747–764. https://doi.org/10.1007/s11837-016-1901-610.1007/s11837-016-1901-6 ↗
4. Zhai, Y., Lados, D.A., and Lagoy, J.L., Additive Manufacturing: Making Imagination the Major Limitation, J. Met., 2014, vol. 66, pp. 808–816. https://doi.org/10.1007/s11837-014-0886-210.1007/s11837-014-0886-2 ↗
5. Zhao, D., Han, Ch., Li, Y., Li, J., Zhou, K., Wei, Q., Liu, J., and Shia, Y., Improvement on Mechanical Properties and Corrosion Resistance of Titanium-Tantalum Alloys In-Situ Fabricated via Selective Laser Melting, J. Alloys Compnd., 2019, vol. 804, pp. 288–298. https://doi.org/10.1016/j.jallocom.2019.06.30710.1016/j.jallocom.2019.06.307 ↗
6. Hattal, A., Chauveau, T., Djemai, M., Fouchet, J.J., Bacroix, B., and Dirras, G., Effect of Nano-Yttria Stabilized Zirconia Addition on the Microstructure and Mechanical Properties of Ti6Al4V Parts Manufactured by Selective Laser Melting, Mater. Design, 2019, vol. 180, p. 107909. https://doi.org/10.1016/j.matdes.201910.1016/j.matdes.2019 ↗
7. Gangireddy, S., Komarasamy, M., Faierson, E.J., and Mishraa, R.S., High Strain Rate Mechanical Behavior of Ti-6Al-4V Octet Lattice Structures Additively Manufactured by Selective Laser Melting (SLM), Mater. Sci. Eng. A, 2019, vol. 745, pp. 231–239. https://doi.org/10.1016/j.msea2018.12.10110.1016/j.msea2018.12.101 ↗
8. Yang, L., Zhicong, P., Ming, L., Yonggang, W., Di, W., Changhui, S., and Shuxin, L., Investigation into the Dynamic Mechanical Properties of Selective Laser Melted Ti-6Al-4V Alloy at High Strain Rate Tensile Loading, Mater. Sci. Eng. A, 2019, vol. 745, pp. 440–449. https://doi.org/10.1016/j.msea2019.01.01010.1016/j.msea2019.01.010 ↗
9. Fadida, R., Rittel, D., and Shirizly, A., Dynamic Mechanical Behavior of Additively Manufactured Ti6AI4V with Controlled Voids, J. Appl. Mech., 2015, vol. 82, p. 041004-1. https://doi.org/10.1115/1.402974510.1115/1.4029745 ↗
10. Ming, W., Chen, J., An, Q., and Chen, M., Dynamic Mechanical Properties and Machinability Characteristics of Selective Laser Melted and Forged Ti6Al4V, J. Mater. Proc. Tech., 2019, vol. 271, pp. 284–292. https://doi.org/10.1016/j.matprotec.2019.04.01510.1016/j.matprotec.2019.04.015 ↗
11. Zaretsky, E., Stern, A., and Frage, N., Dynamic Response of AlSi10Mg Alloy Fabricated by Selective Laser Melting, Mater. Sci. Eng. A, 2017, vol. 688, pp. 364–370. https://doi.org/10.1016/j.msea.2017.02.00410.1016/j.msea.2017.02.004 ↗
12. Laurençon, M., de Resseguier, T., Loison, D., Baillargeat, J., Domfang Ngnekou, J.N., and Nadot, Y., Effects of Additive Manufacturing on the Dynamic Response of AlSi10Mg to Laser Shock Loading, Mater. Sci. Eng. A, 2019, vol. 748, pp. 407–417. https://doi.org/10.1016/j.msea.2019.02.00110.1016/j.msea.2019.02.001 ↗
13. Jack, L., Wise, D.P., Adams, E.E., Nishida, Bo Song, Comparative Shock Response of Additively Manufactured versus Conventionally Wrought 304L Stainless Steel, AIP Conf. Proc., 2017, vol. 1793, p. 100015. https://doi.org/10.1063/1.497164010.1063/1.4971640 ↗
14. Gray, G.T.III, Knapp, C.M., Jones, D.R., Livescu, V., Fensin, S., Morrow, B.M., Trujillo, C.P., Martinez, D.T., and Valdez, J.A., Structure/Property Characterization of Spallation in Wrought and Additively Manufactured Tantalum, AIP Conf. Proc., 2018, vol. 1979, p. 060002. https://doi.org/10.1063/1.504479910.1063/1.5044799 ↗
15. Jones, D.R., Fensin, S.J., Dippo, O., Beal, R.A., Livescu, V., Martinez, D.T., Trujillo, C.P., Florando, J.N., Kumar, M., and Gray, G.T.III, Spall Fracture in Additive Manufactured Ti-6Al-4V, J. Appl. Phys., vol. 120, p. 135902. https://doi.org/10.1063/1.496327910.1063/1.4963279 ↗
16. Kanel, G.I., Razorenov, S.V., Utkin, A.V., and Fortov, V.E., Shock-Wave Phenomena in Condensed Media, Moscow: Yanus-K, 1996.
17. Barker, L.M. and Hollenbach, R.E., Laser Interferometer for Measuring High Velocities of any Reflecting Surface, J. Appl. Phys., 1972, vol. 43, pp. 4669–4675. https://doi.org/10.1063/1.166098610.1063/1.1660986 ↗
18. Dabrowski, R., The Kinetics of Phase Transformations during Continuous Cooling of the Ti6Al4V Alloy from the Single-Phase β Range, Arch. Metal. Mater., 2011, vol. 56, no. 3, p. 705. https://doi.org/10.2478/v10172-011-0025-910.2478/v10172-011-0025-9 ↗
19. Shalnova, S.A., Kuzminova, Y.O., Evlashin, S.A., Klimova-Korsmik, O.G., Vildanov, A.M., Shibalova, A.A., and Turichin, G.A., Effect of Recycled Powder Content on the Structure and Mechanical Properties of Ti-6Al-4V Alloy Produced by Direct Energy Deposition, J. Alloys Compnd., 2022, vol. 893. https://doi.org/10.1016/j.jallcom.2021.16226410.1016/j.jallcom.2021.162264 ↗
20. Sklyar, M.O., Klimova-Korsmik, O.G., Turichin, G.A., and Shalnova, S.A., Influence of Technological Parameters of Direct Laser Deposition Process on the Structure and Properties of Deposited Products from Alloy Ti-6Al-4V, Solid State Phenomena, 2018, vol. 284, pp. 306–311. https://doi.org/10.4028/www.scientific.net/SSP.284.30610.4028/www.scientific.net/SSP.284.306 ↗
21. Turichin, G.A., Klimova-Korsmik, O.G., Gushchina, M.O., Shalnova, S.A., Korsmik, R.S., Cheverikin, V.V., and Tataru, A.S., Features of Structure Formation in α + β Titanium Alloys, Proc. CIRP, 2018, vol. 74, pp. 188–191. https://doi.org/10.1016/j.procir.2018.08.09110.1016/j.procir.2018.08.091 ↗
22. Kanel, G.I., Ashitkov, S.I., Fortov, V.E., Zaretsky, E.B., and Razorenov, S.V., Unusual Plasticity and Strength of Metals at Ultra-Short Load Durations, Physics-Uspekhi, 2017, vol. 60, no. 5, pp. 490–508. https://doi.org/10.3367/UFNr.2016.12.03800410.3367/UFNr.2016.12.038004 ↗
23. Kanel, G.I., Spall Fracture: Methodological Aspects, Mechanisms and Governing Factors, Int. J. Fracture, 2010, vol. 163, no. 1–2, pp. 173–191. https://doi.org/10.1007/s10704-009-9438-010.1007/s10704-009-9438-0 ↗
24. Kanel, G.I., Garkushin, G.V., and Razorenov, S.V., Temperature-Rate Dependences of the Flow Stress and the Resistance to Fracture of a VT6 Titanium Alloy under Shock Loading at a Temperature of 20 and 600ºC, Tech. Phys., 2016, vol. 61, no. 8, pp. 1229–1236. https://doi.org/10.1134/S106378421608013210.1134/S1063784216080132 ↗