Spall Strength of 09CrNi2MoCu Steel Manufactured by Hot Rolling and Direct Laser Deposition in the Submicrosecond Loading Range
Source abstract
Abstract
Abstract Strength measurement results are reported for hot-rolled cast cold-resistant structural alloy steel 09CrNi2MoCu subjected to shock compression up to 15.5 GPa within the strain rate range of 105–106 s–1. Specimens fabricated by direct laser deposition were used to study the effect of the deposition direction and shock compression amplitude on the Hugoniot elastic limit and critical stresses during spall fracture. The strength characteristics were determined by analyzing the full waveform data recorded during loading by a VISAR laser Doppler velocity interferometer. It was found that the spall strength of the cast steel specimens is almost independent of the shock compression pressure, but strongly depends on the strain rate before spalling. The spall strength of the additively manufactured specimens is slightly lower than that of the hot-rolled cast steel specimens and does not depend on the deposition direction. The α ↔ ε phase transformation expected at 13 GPa was not observed in experiments on cast steel 09CrNi2MoCu with the maximum shock compression pressure.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · High-Velocity Impact and Material Behavior
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Frazier, W.E., Metal Additive Manufacturing: A Review, J. Mater. Eng. Perform., 2014, vol. 23, pp. 1917–1928. https://doi.org/10.1007/s11665-014-0958-z10.1007/s11665-014-0958-z ↗
2. Lancaster, R.J., Fortunato, A., and Kolisnychenko, S., Metal Additive Manufacturing, Baech: Trans. Tech. Publ. Ltd., 2020.10.4028/www.scientific.net/978-3-0357-3752-3 ↗
3. Dutta, B., Palaniswamy, S., Choi, J., Song, L.J., and Mazumder, J., Additive Manufacturing by Direct Metal Deposition, Adv. Mater. Process., 2011, vol. 169(5), pp. 33–36. https://doi.org/10.1016/j.phpro.2015.11.05410.1016/j.phpro.2015.11.054 ↗
4. Shamsaei, N., Yadollahi, A., Bian, L., and Thompson, S.M., An Overview of Direct Laser Deposition for Additive Manufacturing. Part II: Mechanical Behavior, Process Parameter Optimization and Control, Additiv. Manuf., 2015, vol. 8, pp. 12–35. https://doi.org/10.1016/j.addma.2015.07.00210.1016/j.addma.2015.07.002 ↗
5. Yap, C.Y., Chua, C.K., Dong, Z.L., Liu, Z.H., Zhang, D.Q., Loh, L.E., and Sing, S.L., Review of Selective Laser Melting: Materials and Applications, Appl. Phys. Rev., 2015, no. 2, p. 041101. https://doi.org/10.1063/1.493592610.1063/1.4935926 ↗
6. Das, S. and Beaman, J.J., US Patent US6676892B2, Direct Selective Laser Sintering of Metals, 2004.
7. Zhao, D., Han, C., Li, Y., Li, J., Zhou, K., Wei, Q., Liu, J., and Shia, Y., Improvement on Mechanical Properties and Corrosion Resistance of Titanium-Tantalum Alloys In-Situ Fabricated via Selective Laser Melting, J. Alloys Compnd., 2009, vol. 804, pp. 288–298. https://doi.org/10.1016/j.jallcom.2019.06.30710.1016/j.jallcom.2019.06.307 ↗
8. Gangireddy, S., Komarasamy, M., Faierson, E.J., and Mishraa, R.S., High Strain Rate Mechanical Behavior of Ti-6Al-4V Octet Lattice Structures Additively Manufactured by Selective Laser Melting (SLM), Mater. Sci. Eng. A, 2019, vol. 745, pp. 231–239. https://doi.org/10.1016/j.msea.2018.12.10110.1016/j.msea.2018.12.101 ↗
9. Fadida, R., Rittel, D., and Shirizly, A., Dynamic Mechanical Behavior of Additively Manufactured Ti6Al4V with Controlled Voids, J. Appl. Mech., 2015, vol. 82, p. 041004-1. https://doi.org/10.1115/1.402974510.1115/1.4029745 ↗
10. Meshcheryakov, Yu.I., Divakov, A.K., Makarevich, I.P., Tomashevskii, V.T., Malyshevskii, Yu.V., and Silnikov, M.V., Determination of Dynamic Characteristics of Plasticity of Structural Materials in the Strain Rate Range 103–105 s–1, Deform. Razr. Mat., 2009, no. 7, pp. 36–41.
11. Wise, J.L., Adams, D.P., Nishida, E.E., Song, B., Maguire, M.C., Carroll, J., Reedlunn, B., Bishop, J.E., and Palmer, T.A., Comparative Shock Response of Additively Manufactured Versus Conventionally Wrought 304L Stainless Steel, AIP Conf. Proc., 2017, vol. 1793, p. 100015. https://doi.org/10.1063/1.497164010.1063/1.4971640 ↗
12. Gray III, G.T., Knapp, C.M., Jones, D.R., Livescu, V., Fensin, S., Morrow, B.M., Trujillo, C.P., Martinez, D.T., and Valdez, J.A., Structure/Property Characterization of Spallation in Wrought and Additively Manufactured Tantalum, AIP Conf. Proc., 2018, vol. 1979, p. 060002. https://doi.org/10.1063/1.504479910.1063/1.5044799 ↗
13. Jones, D.R., Fensin, S.J., Dippo, O., Beal, R.A., Livescu, V., Martinez, D.T., Trujillo, C.P., Florando, J.N., Kumar, M., and Gray III, G.T., Spall Fracture in Additive Manufactured Ti-6Al-4V, J. Appl. Phys., 2016, vol. 120, p. 135902. https://doi.org/10.1063/1.496327910.1063/1.4963279 ↗
14. Brown, D., Ameri, A.H., Gregg, A., Austin, D.C., Escobedo, J.P., Hazell, P.J., East, D., and Quadir, M.Z., Dynamic Mechanical Response of Additive Manufactured Ti-6Al-4V, AIP Conf. Proc., 2018, vol. 1979, p. 070008. https://doi.org/10.1063/1.504481710.1063/1.5044817 ↗
15. Paris, V., Cohen, A., Gudinetsky, E., Hevroni, R., Samuha, S., Osovsky, S., Tiferet, E., and Yosef-Hai, A., Study of Flow Stress and Spallation Strength of Additively Manufactured Ti-6Al-4V Alloy, EPJ Web Conf., 2018, vol. 183, p. 03003. https://doi.org/10.1051/epjconf/20181830300310.1051/epjconf/201818303003 ↗
16. Razorenov, S.V., Garkushin, G.V., Savinykh, A.S., Klimova-Korsmik, O.G., Shalnova, S.A., and Gushchina, M.O., Dynamic Strength of VT6 Titanium Alloy Manufactured by Laser Metal Deposition, Phys. Mesomech., 2022, vol. 25, no. 1, pp. 26–32. https://doi.org/10.1134/S102995992201004010.1134/S1029959922010040 ↗
17. Klimova-Korsmik, O., Turichin, G., Mendagaliyev, R., Razorenov, S., Garkushin, G., Savinykh, A., and Korsmik, R., High-Strain Deformation and Spallation Strength of 09CrNi2MoCu Steel Obtained by Direct Laser Deposition, Metals, 2021, vol. 11, no. 8, p. 1305. https://doi.org/10.3390/met1108130510.3390/met11081305 ↗
18. Mendagaliev, R., Petrova, S.G., Klimova-Korsmik, O.G., Ivanov, S.Yu., and Korsmik, R.S., Influence of Technological Parameters of Direct Laser Deposition on the Structure and Properties of 09CrNi2MoCu Steel Products Operated in the Arctic, in Nedelya Nauki SPbMGTU-2018, 2018, vol. 2, p. 261.
19. Mendagaliyev, R., Turichin, G.A., Klimova-Korsmik, O.G., Zotov, O.G., and Eremeev, A.D., Microstructure and Mechanical Properties of Laser Metal Deposited Cold-Resistant Steel for Arctic Application, Proc. Manuf., 2019, vol. 36, p. 249. https://doi.org/10.1016/j.promfg.2019.08.03210.1016/j.promfg.2019.08.032 ↗
20. Alekseev, V.I., Firsov, A.M., Mendagaliev, R., and Klimova-Korsmik, O.G., Microstructural Features of 09CrNi2MoCu Steel Products Obtained by Direct Laser Deposition Technology, in Nedelya Nauki SPbMGTU-2019, 2019, vol. 1, no. 1, p. 61.
21. Kanel, G.I., Shock Waves in Solid State Physics, Boca Raton: CRC Press, 2019.10.1201/9780429275807 ↗
22. Barker, L.M. and Hollenbach, R.E., Laser Interferometer for Measuring High Velocities of Any Reflecting Surface, J. Appl. Phys., 1972, vol. 43, p. 4669. https://doi.org/10.1063/1.166098610.1063/1.1660986 ↗
23. Kanel’, G.I., Distortion of the Wave Profiles in an Elastoplastic Body upon Spalling, J. Appl. Mech. Tech. Phys., 2001, vol. 42, no. 2, pp. 358–362.10.1023/A:1018804709273 ↗
24. Zaretsky, E.B. and Kanel, G.I., Yield Stress, Polymorphic Transformation, and Spall Fracture of Shock-Loaded Iron in Various Structural States and at Various Temperatures, J. Appl. Phys., 2015, vol. 117, p. 195901. https://doi.org/10.1063/1.492135610.1063/1.4921356 ↗
25. Kanel, G.I., Ashitkov, S.I., Komarov, P.S., Agranat, M.B., Razorenov, S.V., and Garkushin, G.V., Deformation Resistance and Fracture of Iron over a Wide Strain Rate Range, Phys. Sol. State, 2014, vol. 56, no. 8, pp. 1569–1573.10.1134/S1063783414080113 ↗
26. Kanel, G.I., Garkushin, G.V., Savinykh, A.S., Razorenov, S.V., and Atroshenko, S.A., High-Rate Deformation and Fracture of 15Kh2NMFA Steel under Impact Loading at Normal and Elevated Temperatures, Tech. Phys., 2020, vol. 65, no. 3, pp. 420–427.10.1134/S1063784220030111 ↗
27. Garkushin, G.V., Kanel, G.I., Razorenov, S.V., and Savinykh, A.S., Anomaly in the Dynamic Strength of Austenitic Stainless Steel 12Cr19Ni10Ti under Shock Wave Loading, Mech. Sol., 2017, no. 4, pp. 407–416.10.3103/S0025654417040070 ↗
28. Kanel, G.I., Garkushin, G.V., Savinykh, A.S., Razorenov, S.V., and Atroshenko, S.A., Investigation of the Strain Rate Dependences of the Yield Stress and Fracture of 09Mn2SiA-A Steel at Normal and Elevated Temperatures, Zhur. Tekh. Fiz., 2021, vol. 91, no. 11, pp. 1698–1706. https://doi.org/10.21883/JTF.2021.11.51531.116-2110.21883/JTF.2021.11.51531.116-21 ↗