An approach to prediction of microstructure formation near friction surfaces at large plastic strains
Source abstract
Abstract
The paper develops an approach to formulation of constitutive equations for predicting the microstructure formation in a thin material layer near surfaces with high friction stresses in material forming processes. The approach is based on the use of the strain rate intensity factor. An equation relating the layer thickness to the strain rate intensity factor is proposed. A similarity condition that provides the same layer thickness at appropriate friction surface points in full-scale and model experiments is derived. The condition implies that the degree of strain inhomogeneity and hence the degree of inhomogeneity of material properties depends on the scale factor. As an example, compression of a thin layer between parallel plates is considered. Assuming validity of the proposed equation, a relationship is established between the parameters of compression and the layer thickness with essentially changed microstructure.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Powder Metallurgy Techniques and Materials · Metallurgy and Material Forming · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Griffiths, B.J., Mechanisms of White Layer Generation with Reference to Machining and Deformation Processes, Trans. ASME J. Tib., 1987, vol. 109, pp. 525–530.10.1115/1.3261495 ↗
2. Umbrello, D. and Jawahir, I.S., Numerical Modeling of the Influence of Process Parameters and Workpiece Hardness of White Layer Formation in AISI 52100 steel, Int. J. Adv. Manuf. Tech., 2009, vol. 44, pp. 955–968.10.1007/s00170-008-1911-9 ↗
3. Veldhuis, S.C., Dosbaeva, G.K., Elfizy, A., Fox-Rabinovich, G.S., and Wagg, T., Investigations of White Layer Formation during Machining of Powder Metallurgical Ni- Based ME16 Superalloy, J. Mater. Eng. Perform., 2010, vol. 19, pp. 1031–1036.10.1007/s11665-009-9567-7 ↗
4. Umbrello, D., Jayal, A.D., Caruso, S., Dillon, O.W., and Jawahir, I.S., Modeling of White and Dark Layer Formation in Hard Machining of AISI 52100 Bearing Steel, Mach. Sci. Tech., 2010, vol. 14, pp. 128–147.10.1080/10910340903586525 ↗
5. Cho, D.-H., Lee, S.-A., and Lee, Y.-Z., Mechanical Properties and Wear Behavior of the White Layer, Tribol. Lett., 2012, vol. 45, pp. 123–129.10.1007/s11249-011-9869-4 ↗
6. Huang, X., Zhou, Z., Ren, Y., Mao, C., and Li, W., Experimental Research Material Characteristics Effect on White Layers Formation in Grinding of Hardened Steel, Int. J. Adv. Manuf. Tech., 2013, vol. 66, pp. 1555–1561.10.1007/s00170-012-4439-y ↗
7. Murai, T., Matsuoka, S., Miyamoto, S., and Oki, Y., Effects of Extrusion Conditions on Microstructure and Mechanical Properties of AZ31B Magnesium Alloy Extrusions, J. Mater. Process. Tech., 2003, vol. 141, pp. 207–212.10.1016/S0924-0136(02)01106-8 ↗
8. Kajino, S. and Asakawa, M., Effect of “Additional Shear Strain Layer” on Tensile Strength and Microstructure of Fine Drawn Wire, J. Mater. Process. Tech., 2006, vol. 177, pp. 704–708.10.1016/j.jmatprotec.2006.04.108 ↗
9. Trunina, T.A. and Kokovikhin, E.A., Formation ofa Finely Dispersed Structure in Steel Surface Layers under Combined Processing Using Hydraulic Pressing, J. Mach. Manuf. Reliab., 2008, vol. 37, no. 2, pp. 160–162.10.3103/S1052618808020118 ↗
10. Aleksandrov, S.E., Grabko, D.Z., and Shikimaka, O.A., The Determination of the Thickness of a Layer of Intensive Deformations in the Vicinity of the Friction Surface in Metal Forming Processes, J. Mach. Manuf. Reliab., 2009, vol. 38, no. 3, pp. 277–282.10.3103/S105261880903011X ↗
11. Kim, Y.-T. and Ikeda, K., Flow Behavior of the Billet Surface Layer in Porthole Die Extrusion of Aluminum, Metall. Mater. Trans. A, 2000, vol. 31, pp. 1635–1643.10.1007/s11661-000-0173-4 ↗
12. Milenin, A.A., Berski, S., Banaszek, G., and Dyja, H., Theoretical Analysis and Optimization of Parameters in Extrusion Process of Explosive Gladded Bimetallic Rods, J. Mater. Process. Tech., 2004, pp. 157-158, 208–212.
13. Sasaki, T.T., Morris, R.A., Thompson, G.B., Syarif, Y., and Fox, D., Formation of Ultra-Fine Copper Grains in Copper- Clad Aluminum Wire, Scripta Mater., 2010, vol. 63, pp.488–491.10.1016/j.scriptamat.2010.05.010 ↗
14. Thirumurugan, M., Rao, S.A., Kumaran, S., and Rao, T.S., Improved Ductility in ZM21 Magnesium-Aluminium Macrocomposite Produced by Co-extrusion, J. Mater. Process. Tech., 2011, vol. 211, pp. 1637–1642.10.1016/j.jmatprotec.2011.05.005 ↗
15. Li, X., Zu, G., Ding, M., Mu, Y., and Wang, P., Interfacial Microstructure and Mechanical Properties of Cu/Al Clad Sheet Fabricated by Asymmetrical Roll Bonding and Annealing, Mater. Sci. Tech. A, 2011, vol. 529, pp. 485–491.10.1016/j.msea.2011.09.087 ↗
16. Kirpichev, M.V., Theory of Similarity as a Basis for Performing an Experiment, Izv. ANSSSR. Otd. Tekh. Nauk, 1945, no. 4-5, pp. 333–338.
17. Gibbings, J.C., Dimensional Analysis, London: Springer, 2011.10.1007/978-1-84996-317-6 ↗
18. Gubkin, S.I., Similar Deformation Conditions at Metal Treatment by Pressure, Izv. AN SSSR. Otd. Tekh. Nauk, 1947, no. 1, pp. 117–123.
19. Ilyushin, A.A., Modeling of Hot and High-Rate Processes in Metal Forming, Prikl. Mekh. Matem., 1952, vol. 16, no. 4, pp. 385–398.
20. Alexandrov, S. and Richmond, O., Singular Plastic Flow Fields near Surfaces of Maximum Friction Stress, Int. J. Nonlinear Mech., 2001, vol. 36, no. 1, pp. 1–11.10.1016/S0020-7462(99)00075-X ↗
21. Alexandrov, S.E. and Lyamina, E.A., Singular Solutions for Plane Plastic Flow of Materials Sensitive to Mean Pressure, Dokl. RAN, 2002, vol. 383, no. 4, pp. 492–495.
22. Alexandrov, S. and Mishuris, G., Qualitative Behaviour of Viscoplastic Solutions in the Vicinity of Maximum-Friction Surfaces, J. Eng. Math., 2009, vol. 65, no. 2, pp. 143–156.10.1007/s10665-009-9277-z ↗
23. Alexandrov, S. and Jeng, Y.-R., Singular Rigid/Plastic Solutions in Anisotropic Plasticity under Plane Strain Conditions, Cont. Mech. Therm., 2013, vol. 25, no. 5, pp. 685–689.10.1007/s00161-013-0304-y ↗
24. Alexandrov, S.E., Goldstein, R.V., and Lyamina, E.A., Developing the Concept of the Strain Rate Intensity Factor in Plasticity Theory, Doklady Physics, 2003, vol. 48, no. 3, pp. 131–133.10.1134/1.1565618 ↗
25. Alexandrov, S.E. and Goldstein, R.V., Similarity of the Grain Size Evolution near Friction Surfaces and during Equal Channel Extrusion, Dokl. RAN, 2013, vol. 450, no. 2, pp. 162–165.
26. Humphreys, F.J., Prangnell, P.B., Bowen, J.R., Gholinia, A., and Harris, C., Developing Stable Fine-Grain Microstructures by Large Strain Deformation, Phil. Trans. R. Soc. Lond. A, 1999, vol. 357, pp. 1663–1681.10.1098/rsta.1999.0395 ↗
27. Kharitonov, V.A. and Gallyamov, D.E., Scale Effect on the Choice of a Wire Drawing Method, Zagot. Proiz. Mash., 2014, no. 3, pp. 34–37.
28. Kachanov, L.M., Foundations of the Theory of Plasticity, Amsterdam: North-Holland Pub. Co., 1971.
29. Alexandrov, S., The Strain Rate Intensity Factor and Its Applications: a Review, Mater. Sci. Forum, 2009, vol. 623, pp. 1–20.10.4028/www.scientific.net/MSF.623.1 ↗
30. Alexandrov, S., Tzou, G.-Y., and Huang, M.-N., Plane Strain Compression of Rigid/Perfectly Plastic Multi-Layer Strip between Parallel Platens, Acta Mech., 2006, vol. 184, no. 1-4, pp. 103–120.10.1007/s00707-006-0327-6 ↗