Effect of solution heat treatment on the microstructure and mechanical properties of Inconel 625 superalloy fabricated by laser solid forming
Source abstract
Abstract
Abstract In this study, the effect of solution heat treatments on the microstructure and mechanical properties of Inconel 625 superalloy fabricated by laser solid forming was investigated. The microstructure of deposit was mainly composed of columnar grains, which didn't change until the solution temperature reached 1200 °C after solution heat treatment. Due to the large size Laves phase which can pin grain boundary and obstruct grain boundary migration, the recrystallization fully occurred when the solution temperature exceeded 1200 °C. With the increment of the solution temperature, the average diffusion coefficient of solute elements and the dissolution velocity increased obviously. Besides, the volume fraction and size of Laves phase decreased, and the dislocation density decreased apparently. As a result, the microhardness and yield strength decreased with the increment of the solution temperature, but the tensile strength didn't change much after solution heat treatment, and the elongation increased significantly with the solution temperature improving. The room-temperature tensile properties in different states of Inconel 625 fabricated by laser solid forming were higher than those of Inconel 625 fabricated by casting.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. Shoemaker · 2005 · 409
2. Microstructural evolution of cold-sprayed Inconel 625 superalloy coatings on low alloy steel substrate10.1016/j.actamat.2017.02.070 ↗
3. Functionally graded material of 304L stainless steel and inconel 625 fabricated by directed energy deposition: characterization and thermodynamic modeling10.1016/j.actamat.2016.02.019 ↗
4. Microstructural evolution and mechanical properties of differently heat-treated binder jet printed samples from gas- and water-atomized alloy 625 powders10.1016/j.actamat.2016.11.021 ↗
5. Microstructure and deformation behavior of Ti-6Al-4V alloy by high-power laser solid forming10.1016/j.actamat.2017.04.026 ↗
6. Additive manufacturing of strong and ductile Ti–6Al–4V by selective laser melting via in situ martensite decomposition10.1016/j.actamat.2014.11.028 ↗
7. Effect of processing parameters on microstructure and tensile properties of austenitic stainless steel 304L made by directed energy deposition additive manufacturing10.1016/j.actamat.2016.03.019 ↗
8. Microstructures and mechanical behavior of Inconel 718 fabricated by selective laser melting10.1016/j.actamat.2011.12.032 ↗
9. Numerical simulation of transport phenomena, formation the bead and thermal behavior in application to industrial DMD technology10.1016/j.ijheatmasstransfer.2015.12.046 ↗
10. Effect of Ti addition on cracking and microhardness of Inconel 625 during the laser solid forming processing10.1016/j.jallcom.2017.03.355 ↗
11. High-cycle fatigue properties of Alloy 718 base metal and electron beam welded joint ☆10.1016/j.phpro.2015.06.196 ↗
12. The influence of Laves phases on the high-cycle fatigue behavior of laser additive manufactured Inconel 71810.1016/j.msea.2017.03.098 ↗
13. Study of microsegregation and Laves phase in INCONEL718 superalloy regarding cooling rate during solidification10.1007/s11661-014-2614-5 ↗
14. Laves phase control of Inconel 718 alloy using quasi-continuous-wave laser additive manufacturing10.1016/j.matdes.2017.03.004 ↗
15. Effects of laser modes on Nb segregation and Laves phase formation during laser additive manufacturing of nickel-based superalloy10.1016/j.matlet.2016.10.118 ↗
16. Effect of heat treatment and hot isostatic pressing on the microstructure and mechanical properties of Inconel 625 alloy processed by laser powder bed fusion10.1016/j.msea.2017.02.038 ↗
17. Laser aided direct metal deposition of Inconel 625 superalloy: microstructural evolution and thermal stability10.1016/j.msea.2009.01.009 ↗
18. Investigation on dissolution mechanism of Laves phase in GH4169 alloy ingot based on classical dynamical model10.3724/SP.J.1037.2012.00564 ↗
19. 2013
20. Kurz · 1998
21. Columnar to equiaxed transition in solidification processing10.1016/S1468-6996(01)00047-X ↗
22. Single-crystal laser deposition of superalloys: processing–microstructure maps10.1016/S1359-6454(00)00367-0 ↗
23. Columnar to equiaxed transition during alloy solidification10.1360/02ye0337 ↗
24. Laser repair of superalloy single crystals with varying substrate orientations10.1007/s11661-007-9172-z ↗
25. Steady state columnar and equiaxed growth of dendrites and eutectic10.1016/0025-5416(84)90201-5 ↗
26. Solidification of Nb-bearing superalloys: Part I. Reaction sequences10.1007/s11661-998-0319-3 ↗
27. Solidification of Nb-bearing superalloys: Part II. Pseudoternary solidification surfaces10.1007/s11661-998-0320-x ↗
28. The effect of hot isostatic pressing on crack healing, microstructure, mechanical properties of Rene88DT superalloy prepared by laser solid forming10.1016/j.msea.2008.12.024 ↗
29. Recrystallization and its influence on microstructures and mechanical properties of laser solid formed nickel base superalloy Inconel 71810.1007/s12598-011-0319-0 ↗
30. Evolution of interface and crystal orientation of laser solid formed GH4169 superalloy during recrystallization
31. Temperature and stress fields of multi-track laser cladding
32. Impact of thermomechanical aging on alloy 625 high temperature mechanical properties
33. Particle dissolution and cross-diffusion in multi-component alloys10.1016/S0921-5093(02)00615-9 ↗
34. Precipitate dissolution and its dependence on growth mode10.1016/0001-6160(69)90021-2 ↗
35. Strengthening mechanisms in polycrystalline multimodal nickel-base superalloys10.1007/s11661-009-9858-5 ↗
36. Additively manufactured hierarchical stainless steels with high strength and ductility10.1038/nmat5021 ↗
37. Modeling solid solution strengthening in nickel alloys10.1007/s11661-997-0268-2 ↗
38. Dislocation densities in some annealed and cold-worked metals from measurements on the X-ray debye-scherrer spectrum10.1080/14786435608238074 ↗
39. A modelling approach to yield strength optimisation in a nickel-base superalloy10.1016/j.ijplas.2013.08.009 ↗
40. ASTM A494/494M: Standard Specification for Castings, Nickel and Nickel Alloy (ASTM International, West Conshohocken).