Pullout Tests on Concrete Breakout Strength of Headed Reinforcement Bars Embedded in Roof Exterior Beam-Column Joints
Source abstract
Abstract
Recently, the use of headed bars as mechanical anchorage in reinforced concrete beam-column joints has increased rapidly. This type of anchorage is used for T-shaped beam and exterior column joints at middle floors and for L- and T-shaped beam-column joints at the rooftops of buildings. However, few experimental data are available regarding the anchorage capacity of headed bars embedded in L-shaped beam-column joints. Nine pullout tests are conducted to investigate the anchorage capacity of headed bars embedded in L-shaped beam-column joints. Parameters affecting the anchorage capacity, such as the diameter, embedment length, location of the headed bars, and the number of supplementary bars are considered. The anchorage capacity of the headed bars is evaluated using empirical formulas proposed by Kubota and Murakami and a formula for concrete cone failure. The failure behavior of the specimens is concrete failure with cracks propagating in the diagonal direction at the maximum applied load. The anchorage capacity increases with the embedment length and diameter of the headed bars, number of supplementary bars, and concrete area. For most specimens, the Kubota and Murakami formulas overestimate the anchorage capacity, whereas formula for concrete cone failure yields lower anchorage capacities as compared with the test results.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Structural Behavior of Reinforced Concrete · Structural Load-Bearing Analysis · Seismic Performance and Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Toyohashi University of Technology, Aichi, Japan.
Osaka University, Osaka, Japan.
Horie Engineering and Architectural Research Institute, Tokyo, Japan.
Tokyo Tekko Co., Ltd., Tokyo, Japan.
References (23)
Show source-provided references
1. 1) Alrasyid, H., Yoganata, Y. S., Suluch, M. and Iranata, D., (2017). “Headed reinforcement in concrete structure: State of the art.” In: Proceedings of the 3rd International Conference on Construction and Building Engineering (ICONBUILD), Palembang 14-17 August 2017. AIP Publishing, 020015.10.1063/1.5011495 ↗
2. 2) Abed, H. S., Abed, J. M. and Al-Rawe, H. S., (2021). “Anchorage behavior of headed bars in reinforced concrete beams.” Structures, 29, 2352-0124.10.1016/j.istruc.2020.12.066 ↗
3. 3) Alaee, P. and Li, B., (2017). “High-strength concrete exterior beam-column joints with high-yield strength steel reinforcements.” Engineering Structures, 145, 305-321.10.1016/j.engstruct.2017.05.024 ↗
4. 4) AIJ, (2010). “AIJ standard for structural calculation of reinforced concrete structures.” Tokyo: Architectural Institute of Japan.
5. 5) Choi, D. U., (2006). “Test of headed reinforcement in pullout II: Deep embedment.” International Journal of Concrete Structures and Materials, 18(3E), 151-159.10.4334/IJCSM.2006.18.3E.151 ↗
6. 6) Chun, C. S., Bohwan, O., Ho, L. S. and Clay, N. J., (2009). “Anchorage strength and behavior of headed bars in exterior beam-column joints.” ACI Structural Journal, 106(5), 579-590.10.14359/51663098 ↗
7. 7) Chourasia, A. and Gupta, S., (2019). “Influential parameters for headed bars in RC beam-column joint.” Current Science, 116(10), 1666-1673.10.18520/cs/v116/i10/1666-1673 ↗
8. 8) Ferreira, M., Filho, M. P., Lima, N. and Oliveira, M., (2021). “Influence of the flexural and shear reinforcement in the concrete cone resistance of headed bars.” Engineering Structures, 248, 113212.10.1016/j.engstruct.2021.113212 ↗
9. 9) Gao, F., Tang, Z., Mei, S., Hu, B., Hunag, S. and Chen, J., (2021). “Seismic behavior of exterior beam–column joints with high-performance steel rebar: Experimental and numerical investigations.” Advances in Structural Engineering, 24(1), 90-106.10.1177/1369433220942870 ↗
10. 10) Ghali, A. and Youakim, S. A., (2005). “Headed studs in concrete: State of the art.” ACI Structural Journal, 102(5), 657-667.10.14359/14661 ↗
11. 11) JBDPA, (2001). “Guideline for seismic retrofit of existing reinforced concrete building.” Tokyo: The Japan Building Disaster Prevention Association.
12. 12) Johnson, L. A., and Jirsa, J. O., (1981). "The influence of short embedment and close spacing on the strength of hooked bar anchorages (PMFSEL Report No. 81-2)." University of Texas, Austin.
13. 13) Kawale, A. and Patil, Y. D., (2016). “Pullout capacity and bond behavior of headed reinforcement in concrete.” International Journal of Innovative Research in Science, Engineering and Technology, 5(7), 39-45.
14. 14) Kang, T. H.-K., Ha, S.-S. and Choi, D.-U., (2010). “Bar pullout tests and seismic tests of small-headed bars in beam-column joints.” ACI Structural Journal, 107(1), 32-42.10.14359/51663386 ↗
15. 15) Kang, T. H.-K., Shin, M., Mitra, N. and Bonacci, J. F., (2009). “Seismic design of reinforced concrete beam-column joints with headed bars.” ACI Structural Journal, 106(6), 868-877.10.14359/51663188 ↗
16. 16) Murakami, M., Fuji, T. and Kubota, T., (1997). “Evaluation of mechanical anchorage capacities of main bars in beam-column joints based on pull-out tests.” Concrete Research and Technology, 8(2), 1-10. (in Japanese).10.3151/crt1990.8.2_1 ↗
17. 17) Pawar, V. R., Patil, Y. D. and Patil, H. S., (2017). “Cyclic loading of exterior beam - column joint with threaded headed reinforcement.” International Journal of Applied Engineering Research, 12(17), 6377-6383.
18. 18) Perumal, N. M. and Varkeesh, A., (2018). “Experimental study on bond behavior of threaded headed bars.” International Journal of Current Engineering and Scientific Research, 5(12), 39-45.
19. 19) Shen, X., Li, B. and Lam, E. S. S., (2020). “Experimental investigation on reinforced concrete interior beam-column joints with headed diagonal bars.” 17 th World Conference on Earthquake Engineering (WCEE), Sendai 13-18 September 2020. 17WCEE, 2c-0019.
20. 20) Shao, Y., Darwin, D., O'Reilly, M., Lequesne, R. D., Ghimire, K. P. and Hano. M., (2016). "Anchorage of conventional and high-strength headed reinforcing bars (SM Report No. 117)." Lawrence: University of Kansas Center for Research Inc.
21. 21) Tran, M. T., Bui, Q. B., Sentosa, B., Nguyen, N. T., Duong, T. H. and Ple, O., (2018). “Sustainable RC beam-column connections with headed bars: A formula for shear strength evaluation.” Sustainability, 10(2), 401.10.3390/su10020401 ↗
22. 22) Yang, Y., Varma, A. H., Kreger, M. E., Wang, Y. and Zhang, K., (2021). “Shear strength of reinforced concrete beams with T-headed bars for safety-related nuclear structures.” Engineering Structures, 230, 111705.10.1016/j.engstruct.2020.111705 ↗
23. 23) Yu-Chen, O., Canseco, H. A. and Kurniawan, D. P., (2017). “Anchorage performance of headed deformed bars in exterior beam-column joints under cyclic loading.” KSCE Journal of Civil Engineering, 21, 2837–2849.10.1007/s12205-017-1868-z ↗