Determination of shear force capacity of H-type box furniture joints connected with different demountable type of connection elements
Source abstract
Abstract
In this study, the performances of type of demountable connectors used as connecting elements in the frame construction furniture are compared with the forces against shear force. The test samples were prepared from melamine-coated particle board (YL-Lam) and medium density fiberboard (MDF-Lam). Four types of demountable type of connection elements are used: metal L connection, plastic T connection, metal T connection and moon connection. The experimental samples were subjected to static stress tests under the critical loads that could be affected during the use. As a result of the experiments, the highest shear force was obtained from the test specimens prepared by using MDF-Lam and metal T connectors. The lowest was determined by using YL-Lam and plastic T connector. According to the results of the experiment, in the H type construction prepared with YL-Lam, when the shear force bearing capacity of the connection element is ordered from highest to lowest, respectively; Metal T, Moon, Metal L and Plastic T connectors were determined while in the construction prepared with MDF-Lam it is ordered as Metal T, Metal L, Plastic T and Moon connectors. In this study, the load-bearing capacity of the test samples and the load-deflection graph formed under this loading are given.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Structural Analysis of Composite Materials · Wood Treatment and Properties · Textile materials and evaluations
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Design, Safranbolu Vocational High School, Karabuk University, Karabuk, Turkey;
Department of Forestry, Banaz Vocational High School, Usak University, Usak, Turkey;
Department of Architectural Restoration, Safranbolu Vocational High School, Karabuk University, Karabuk, Turkey
References (20)
Show source-provided references
1. Trinka M · Forest Prod J USA · 1989 · 40 · 35
2. Smardzweski J · Electr J Polish Agri Univ · 2002 · 36 · 173
3. Diesel T. Mechanical behavior properties of the frame type furniture joints constructed of laminated veneer lumber (LVL). Master Thesis, Gazi University Institute of Science and Technology, Ankara; 2005. p.118.
4. Kasal A · Journal of Forestry Faculty · 2012 · 12 · 209
5. Bala E. Mechanical performance characteristics of some joints produced from wood plastic composite materials [master thesis]. Mugla: Mugla Sitki Koçaman University Institute of Science and Technology; 2018. p. 71.
6. Karaman A · Artvin Coruh Univ J Forest Faculty · 2018 · 19 · 144
7. TS EN 322 wood-based panels – determination of moisture content. T.S.E., Ankara; 1999.
8. TS EN 323 wood-based panels – determination of density. T.S.E., Ankara; 1999.
9. Deniz E. Strength properties of case furniture joints constructed with solid wood and plastic dowels [master thesis]. Ankara: Gazi University Institute of Science and Technology; 2010. p. 54.
10. Kasal A · Gazi Univ J Sci · 2006 · 19 · 155
11. Kasal A · Forest Prod J · 2008 · 58 · 36
12. Örs Y · Tr J Agri Forest · 1998 · 22 · 21
13. Kasal A. Mobilya Masa Ayak – Kayıt Birleştirmelerde Köşe Takozunun Birleştirme Mukavemetine Etkileri [master thesis]. Ankara: Gazi University Institute of Science and Technology; 1998. p.67.
14. Efe H · J Polytechnic · 1999 · 2 · 43
15. Şafak R. Mechanical characteristics of corner joint in case construction of furniture [master thesis]. Ankara: Gazi University Institute of Science and Technology; 2000. p. 47.
16. Şakacı D. Effects of plastic-based material employed in furniture manufacturing on compression and tensile performances of various joint techniques [master thesis]. Ankara: Gazi University Institute of Science and Technology; 2010. p. 76.
17. Tüfekli Y. Moment capacity of l-type furniture corner joints constructed with different joints techniques and honeycomb filled panels [master thesis]. Ankara: Gazi University Institute of Science and Technology; 2010. p. 59.
18. Efe H · Kastamonu Univ J Forest Faculty · 2012 · 12 · 80
19. Yıldırım MN, Karaman A. Determination of diagonal pressure and tensile strength capacities of the t-type furniture joints reinforced with different assembly type connection elements. 2nd International Symposium on Multidisciplinary Studies and Innovative Technologies, Kızılcahamam; Ankara, Turkey; 2018 Oct 19–21. p. 299–307.
20. Karabulut S. Furniture corner joint elements used in connection with the finite element method analysis of strength [master thesis]. Karabuk: Karabuk University Institute of Science and Technology; 2010. p. 68.