Underwater friction stir welding of ultrafine-grained laminated composites produced through accumulative roll bonding process
Source abstract
Abstract
In this work, ultrafine-grained (UFG) plates of AA2024/AA5083 laminated composite with alternating layers of heat-treatable aluminum AA2024 and strain-hardening aluminum AA5083 were fabricated through accumulative roll bonding (ARB) technique and were subsequently joined using underwater friction stir welding (UFSW). Friction stir welding (FSW) is a solid-state welding method which is suitable for the joining of similar and dissimilar UFG alloys of AA2024 and AA5083, which are mainly used in aerospace and aviation industries. Welding variables, such as pin profile, rotational speed, welding speed, and tilt angle were optimized using the Taguchi optimization technique. Different zones of UFSWed joints including stir zone (SZ), thermo-mechanically affected zone (TMAZ), and heat affected zone (HAZ) were investigated through OM, TEM, and SEM. The results showed that the tapered cylindrical pin, 1000 rpm rotational speed, 110 mm.min−1 welding speed, and 2.5° tilt angle were the optimal welding variables in terms of tensile strength. The microstructural results showed the formation of nano-size, recrystallized equiaxed grains with a size of 500 nm (the same size as that in the UFG base metal) in the optimal sample. The hardness in the weldment of the optimal UFSW sample decreased slightly, so that the efficiency of 85% was presented and the minimum hardness location (MHL) disappeared. The ultimate tensile strength (UTS) of 425 MPa and 64% efficiency were observed in the optimal conditions. Due to the presence of very fine grains and large dislocations, and the uniform distribution of precipitates in the underwater state, high strength and elongation were obtained.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Faculty of Materials and Metallurgical Engineering, Semnan University, Semnan, Iran
References (99)
Show source-provided references
1. 10.1016/S0921-5093(02)00709-810.1016/S0921-5093(02)00709-8 ↗
2. 10.1016/j.jallcom.2008.06.16110.1016/j.jallcom.2008.06.161 ↗
3. 10.1016/j.msea.2008.06.02510.1016/j.msea.2008.06.025 ↗
4. 10.1016/j.cirp.2008.09.00510.1016/j.cirp.2008.09.005 ↗
5. 10.1016/S1359-6454(98)00365-610.1016/S1359-6454(98)00365-6 ↗
6. 10.1016/S1359-6462(99)00015-910.1016/S1359-6462(99)00015-9 ↗
7. 10.1016/j.msea.2012.08.10910.1016/j.msea.2012.08.109 ↗
8. 10.1016/j.matdes.2015.08.12910.1016/j.matdes.2015.08.129 ↗
9. 10.1016/j.msea.2009.07.07110.1016/j.msea.2009.07.071 ↗
10. 10.1016/j.msea.2015.09.10610.1016/j.msea.2015.09.106 ↗
11. 10.1016/S1359-6462(01)01000-410.1016/S1359-6462(01)01000-4 ↗
12. 10.1016/j.msea.2012.02.08210.1016/j.msea.2012.02.082 ↗
13. Rajiv S, Mishra MWM. Friction stir welding and processing. Detroit (MI): ASM International; 2007.
14. 10.1016/j.corsci.2011.05.04910.1016/j.corsci.2011.05.049 ↗
15. 10.1177/146442071562729410.1177/1464420715627294 ↗
16. Mishra RS, De PS, Kumar N. Friction stir welding and processing: science and engineering. Sci Eng. 2014;9783319070:1–338.
17. 10.1016/j.matdes.2008.08.03410.1016/j.matdes.2008.08.034 ↗
18. 10.1016/j.corsci.2006.05.03810.1016/j.corsci.2006.05.038 ↗
19. 10.3390/ma1406156110.3390/ma14061561 ↗
20. 10.1007/s11661-998-0021-510.1007/s11661-998-0021-5 ↗
21. 10.1016/S1003-6326(18)64653-910.1016/S1003-6326(18)64653-9 ↗
22. 10.1016/j.matdes.2011.06.02110.1016/j.matdes.2011.06.021 ↗
23. 10.1016/j.msea.2005.04.03210.1016/j.msea.2005.04.032 ↗
24. 10.1016/j.actamat.2007.09.00410.1016/j.actamat.2007.09.004 ↗
25. 10.1016/j.jmatprotec.2007.12.00810.1016/j.jmatprotec.2007.12.008 ↗
26. 10.1016/S0921-5093(01)01358-210.1016/S0921-5093(01)01358-2 ↗
27. 10.2478/IJNAOE-2013-000510.2478/IJNAOE-2013-0005 ↗
28. 10.1016/S1359-6454(02)00259-810.1016/S1359-6454(02)00259-8 ↗
29. 10.1016/S0921-5093(99)00674-710.1016/S0921-5093(99)00674-7 ↗
30. 10.1016/j.msea.2018.12.01410.1016/j.msea.2018.12.014 ↗
31. 10.1016/j.dt.2016.02.00310.1016/j.dt.2016.02.003 ↗
32. 10.1016/j.matdes.2011.03.07310.1016/j.matdes.2011.03.073 ↗
33. Mohd Atif W, Arshad N S, Zahid AK. Tanveer Majeed NS. Friction stir welding of AA-5754 in water and air: a comparative study. Mater Res Express. 2018;6:1–19.
34. 10.1016/j.matdes.2015.09.03810.1016/j.matdes.2015.09.038 ↗
35. 10.1016/j.scriptamat.2003.09.03710.1016/j.scriptamat.2003.09.037 ↗
36. 10.1016/j.msea.2007.12.05710.1016/j.msea.2007.12.057 ↗
37. 10.1016/j.jmst.2017.02.00810.1016/j.jmst.2017.02.008 ↗
38. 10.1007/s10853-017-1897-510.1007/s10853-017-1897-5 ↗
39. 10.1016/j.matdes.2010.05.00710.1016/j.matdes.2010.05.007 ↗
40. 10.1016/0376-0421(95)00004-610.1016/0376-0421(95)00004-6 ↗
41. 10.1016/j.matdes.2010.04.03510.1016/j.matdes.2010.04.035 ↗
42. 10.1002/adem.20031007710.1002/adem.200310077 ↗
43. 10.1016/j.jallcom.2019.07.09210.1016/j.jallcom.2019.07.092 ↗
44. 10.1016/j.matdes.2011.12.02210.1016/j.matdes.2011.12.022 ↗
45. Raweni A, Majstorović V, Sedmak A, et al. Optimization of AA5083 friction stir welding parameters using taguchi method. Teh VCsn. 2018;25:861–866.
46. Durakovic B. Design of experiments application, concepts, examples: state of the art. Period Eng Nat Sci. 2017;5:421–439.
47. Roy RK. A primer on taguchi method. 2nd ed. Southfield (MI): Society for Manufacturing Engineers; 2010.
48. 10.1007/s11665-013-0499-x10.1007/s11665-013-0499-x ↗
49. 10.1016/j.jmatprotec.2006.08.02510.1016/j.jmatprotec.2006.08.025 ↗
50. 10.1007/s12008-023-01409-210.1007/s12008-023-01409-2 ↗
51. 10.1007/s12008-023-01425-210.1007/s12008-023-01425-2 ↗
52. 10.1016/j.mspro.2014.07.02210.1016/j.mspro.2014.07.022 ↗
53. 10.1016/j.matdes.2013.10.02110.1016/j.matdes.2013.10.021 ↗
54. 10.1016/j.matpr.2021.11.33310.1016/j.matpr.2021.11.333 ↗
55. 10.1016/j.matdes.2009.06.04910.1016/j.matdes.2009.06.049 ↗
56. 10.1007/s11665-016-2273-310.1007/s11665-016-2273-3 ↗
57. 10.1016/j.matdes.2013.04.07410.1016/j.matdes.2013.04.074 ↗
58. 10.1016/j.msea.2012.12.01410.1016/j.msea.2012.12.014 ↗
59. Mishra RS, Sidhar H. Friction stir welding of 2XXX aluminum alloys including Al-Li alloys. Vol. 1–102. Oxford: Butterworth-Heinemann; 2016.
60. 10.1016/j.matdes.2011.11.00410.1016/j.matdes.2011.11.004 ↗
61. Mehdi H, Mishra RS. Investigation of mechanical properties and heat transfer of welded joint of AA6061 and AA7075 using TIG + FSP welding approach. J Adv Join. 2020;100003.
62. 10.1016/j.msea.2014.06.09310.1016/j.msea.2014.06.093 ↗
63. 10.1016/j.matdes.2010.09.03210.1016/j.matdes.2010.09.032 ↗
64. 10.1016/j.matdes.2013.11.07110.1016/j.matdes.2013.11.071 ↗
65. 10.1007/s11665-014-0968-x10.1007/s11665-014-0968-x ↗
66. 10.2320/matertrans.L-MZ20110210.2320/matertrans.L-MZ201102 ↗
67. 10.1016/j.scriptamat.2005.07.01610.1016/j.scriptamat.2005.07.016 ↗
68. 10.1016/S0921-5093(01)01416-210.1016/S0921-5093(01)01416-2 ↗
69. 10.1016/j.msea.2021.14208010.1016/j.msea.2021.142080 ↗
70. 10.1016/j.msea.2011.12.02610.1016/j.msea.2011.12.026 ↗
71. 10.1016/j.ijfatigue.2010.11.02510.1016/j.ijfatigue.2010.11.025 ↗
72. 10.1016/j.actamat.2007.06.04310.1016/j.actamat.2007.06.043 ↗
73. 10.1016/j.pmatsci.2020.10075210.1016/j.pmatsci.2020.100752 ↗
74. 10.1016/j.msea.2020.13907610.1016/j.msea.2020.139076 ↗
75. 10.1016/B978-008044164-1/50013-X10.1016/B978-008044164-1/50013-X ↗
76. 10.1080/10408436.2017.135814510.1080/10408436.2017.1358145 ↗
77. 10.1016/j.matdes.2016.09.01210.1016/j.matdes.2016.09.012 ↗
78. 10.1007/s11661-999-0223-510.1007/s11661-999-0223-5 ↗
79. 10.1016/j.jmapro.2018.12.01410.1016/j.jmapro.2018.12.014 ↗
80. Fujii H, Cui L, Tsuji N, et al. Mechanical properties of friction stir welds of ultrafine grained steel and other materials. Int J Offshore Polar Eng. 2005;2005:22–26.
81. 10.4028/www.scientific.net/MSF.584-586.83310.4028/www.scientific.net/MSF.584-586.833 ↗
82. 10.1080/13621718.2016.120317710.1080/13621718.2016.1203177 ↗
83. 10.1007/s11665-011-0060-810.1007/s11665-011-0060-8 ↗
84. 10.1016/j.jmatprotec.2016.06.01510.1016/j.jmatprotec.2016.06.015 ↗
85. 10.2320/matertrans.MH20151210.2320/matertrans.MH201512 ↗
86. 10.1016/j.jmapro.2018.01.01610.1016/j.jmapro.2018.01.016 ↗
87. 10.1007/s11661-007-9459-010.1007/s11661-007-9459-0 ↗
88. 10.1016/j.scriptamat.2007.09.06210.1016/j.scriptamat.2007.09.062 ↗
89. 10.1016/j.matdes.2013.04.00210.1016/j.matdes.2013.04.002 ↗
90. 10.1016/j.jmapro.2019.11.03110.1016/j.jmapro.2019.11.031 ↗
91. 10.1179/13621710322500548010.1179/136217103225005480 ↗
92. Hui-Jie LIU, Hui-Jie Z, Yong-Xian H, et al. Mechanical properties of underwater friction stir welded 2219 aluminum alloy. T Nonferr Metal Soc. 2009;20:1387–1391.
93. 10.1016/S0921-5093(03)00008-X10.1016/S0921-5093(03)00008-X ↗
94. 10.1016/j.actamat.2005.02.00710.1016/j.actamat.2005.02.007 ↗
95. 10.1179/1362171811Y.000000002010.1179/1362171811Y.0000000020 ↗
96. 10.1007/s00170-014-6543-710.1007/s00170-014-6543-7 ↗
97. 10.1016/j.pmatsci.2005.08.00310.1016/j.pmatsci.2005.08.003 ↗
98. 10.1016/S0079-6425(99)00007-910.1016/S0079-6425(99)00007-9 ↗
99. 10.1016/j.stam.2003.10.01910.1016/j.stam.2003.10.019 ↗