Smaller is better: reducing silver nanoparticle size without excess ligands enhances conductivity and flexibility in printed thin films
Source abstract
Abstract
Achieving simultaneous high conductivity and mechanical durability in printed flexible electronics remains a central challenge. Here we report a systematic investigation of silver nanoparticle (AgNP) size effects on film performance using a pH-mediated synthesis that decouples particle size from organic content. This strategy enables direct assessment of size-dependent sintering and mechanical behaviors, previously obscured by varied polymer concentrations of traditional size control methods. With consistent organic content, AgNPs of smaller size demonstrated more effective sintering, forming denser and more cohesive microstructures, contrary to prior reports with varied organic concentration. This yielded highly conductive films with resistivities as low as 2.34 μΩ cm, approaching bulk silver. Additionally, electrohydrodynamic (EHD) printing of these inks produced flexible circuits with significantly improved mechanical resilience. The resistance of a printed pattern remained stable over 1,000 bending cycles at a 2.9 mm radius and increased by only 56.7% after 50,000 cycles, with no visible microstructural cracking.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Nanomaterials and Printing Technologies · Advanced Sensor and Energy Harvesting Materials · Surface Modification and Superhydrophobicity
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. Wiklund, J. et al. A Review on Printed Electronics: Fabrication Methods, Inks, Substrates, Applications and Environmental Impacts. J. Manuf. Mater. Process. 5, 89 (2021).
2. Zikulnig, J. et al. Printed Electronics Technologies for Additive Manufacturing of Hybrid Electronic Sensor Systems. Adv. Sens. Res. 2, 2200073 (2023).10.1002/adsr.202200073 ↗
3. Espera, A. H., Dizon, J. R. C., Valino, A. D. & Advincula, R. C. Advancing flexible electronics and additive manufacturing. Jpn. J. Appl. Phys. 61, SE0803 (2022).10.35848/1347-4065/ac621a ↗
4. Beedasy, V. & Smith, P. J. Printed Electronics as Prepared by Inkjet Printing. Materials 13, 704 (2020).10.3390/ma13030704 ↗
5. Zhang, Y. et al. Ink formulation, scalable applications and challenging perspectives of screen printing for emerging printed microelectronics. J. Energy Chem. 63, 498–513 (2021).10.1016/j.jechem.2021.08.011 ↗
6. Wilkinson, N. J., Smith, M. A. A., Kay, R. W. & Harris, R. A. A review of aerosol jet printing—a non-traditional hybrid process for micro-manufacturing. Int. J. Adv. Manuf. Technol. 105, 4599–4619 (2019).10.1007/s00170-019-03438-2 ↗
7. Yin, Z. et al. Electrohydrodynamic printing for high resolution patterning of flexible electronics toward industrial applications. InfoMat 6 (2024).10.1002/inf2.12505 ↗
8. Huang, Y. et al. Memory Manufacture Under Microgravity (MMuM): In-Space Manufactured ZnO-Based Resistive Random Access Memory for Emerging Computing Application. Adv. Electron. Mater. 11, 2500114 (2025).10.1002/aelm.202500114 ↗
9. Sanchez-Duenas, L. et al. A Review on Sustainable Inks for Printed Electronics: Materials for Conductive, Dielectric and Piezoelectric Sustainable Inks. Materials 16, 3940 (2023).10.3390/ma16113940 ↗
10. Htwe, Y. & Mariatti, M. Printed graphene and hybrid conductive inks for flexible, stretchable, and wearable electronics: Progress, opportunities, and challenges. J. Sci.: Adv. Mater. Devices 7, 100435 (2022).
11. Tan, H. W., An, J., Chua, C. K. & Tran, T. Metallic Nanoparticle Inks for 3D Printing of Electronics. Adv. Electron. Mater. 5, 1800831 (2019).10.1002/aelm.201800831 ↗
12. Seo, M., Kim, J. S., Lee, J. G., Kim, S. B. & Koo, S. M. The effect of silver particle size and organic stabilizers on the conductivity of silver particulate films in thermal sintering processes. Thin Solid Films 616, 366–374 (2016).10.1016/j.tsf.2016.08.060 ↗
13. Park, H.-J. et al. Physical Characteristics of Sintered Silver Nanoparticle Inks with Different Sizes during Furnace Sintering. Materials 17, 978 (2024).10.3390/ma17050978 ↗
14. Ding, J. et al. Preparing of Highly Conductive Patterns on Flexible Substrates by Screen Printing of Silver Nanoparticles with Different Size Distribution. Nanoscale Res. Lett. 11 (2016).10.1186/s11671-016-1640-1 ↗
15. Mo, L. et al. Nano-Silver Ink of High Conductivity and Low Sintering Temperature for Paper Electronics. Nanoscale Res. Lett. 14 (2019).10.1186/s11671-019-3011-1 ↗
16. Shang, Y. et al. Improvement of Electrical and Mechanical Properties of Printed Silver Wire by Adjusting Particle Size Distribution of Multiscale Silver Nanoparticle Ink. J. Electron. Mater. 51, 6503–6511 (2022).10.1007/s11664-022-09887-y ↗
17. Zhao, C. F., Wang, J., Zhang, Z. Q., Sun, Z. & Maimaitimin, Z. Silver-Based Conductive Ink on Paper Electrodes Based on Micro-Pen Writing for Electroanalytical Applications. ChemElectroChem 9 (2022).10.1002/celc.202200948 ↗
18. Kirscht, T. et al. Silver Nano-Inks Synthesized with Biobased Polymers for High-Resolution Electrohydrodynamic Printing Toward In-Space Manufacturing. ACS Appl. Mater. Interfaces 16, 44225–44235 (2024).10.1021/acsami.4c07592 ↗
19. Qin, Y. et al. Size control over spherical silver nanoparticles by ascorbic acid reduction. Colloids Surf. A: Physicochem. Eng. Asp. 372, 172–176 (2010).10.1016/j.colsurfa.2010.10.013 ↗
20. Goia, D. V. Preparation and formation mechanisms of uniform metallic particles in homogeneous solutions. J. Mater. Chem. 14, 451–458 (2004).10.1039/b311076a ↗
21. Wang, T., Wang, X., Lou, Z., Ni, M. & Cen, K. Mechanisms of Viscosity Increase for Nanocolloidal Dispersions. J. Nanosci. Nanotechnol. 11, 3141–3150 (2011).10.1166/jnn.2011.3613 ↗
22. Koca, H. D. et al. Effect of particle size on the viscosity of nanofluids: A review. Renew. Sustain. Energy Rev. 82, 1664–1674 (2018).10.1016/j.rser.2017.07.016 ↗
23. Cao, T., Yang, Z., Zhang, H. & Wang, Y. Inkjet printing quality improvement research progress: A review. Heliyon 10, e30163 (2024).10.1016/j.heliyon.2024.e30163 ↗
24. Guo, L., Duan, Y., Huang, Y. & Yin, Z. Experimental Study of the Influence of Ink Properties and Process Parameters on Ejection Volume in Electrohydrodynamic Jet Printing. Micromachines 9, 522 (2018).10.3390/mi9100522 ↗
25. Zhang, Z. et al. Synthesis of monodisperse silver nanoparticles for ink-jet printed flexible electronics. Nanotechnology 22, 425601 (2011).10.1088/0957-4484/22/42/425601 ↗
26. Vaseem, M., Lee, K. M., Hong, A.-R. & Hahn, Y.-B. Inkjet Printed Fractal-Connected Electrodes with Silver Nanoparticle Ink. ACS Appl. Mater. Interfaces 4, 3300–3307 (2012).10.1021/am300689d ↗
27. Hwang, J.-Y. & Moon, S.-J. The Characteristic Variations of Inkjet-Printed Silver Nanoparticle Ink During Furnace Sintering. J. Nanosci. Nanotechnol. 13, 6145–6149 (2013).10.1166/jnn.2013.7662 ↗
28. Ryu, K., Moon, Y.-J., Park, K., Hwang, J.-Y. & Moon, S.-J. Electrical Property and Surface Morphology of Silver Nanoparticles After Thermal Sintering. J. Electron. Mater. 45, 312–321 (2016).10.1007/s11664-015-4073-1 ↗
29. Wang, D.-Y., Chang, Y., Wang, Y.-X., Zhang, Q. & Yang, Z.-G. Green water-based silver nanoplate conductive ink for flexible printed circuit. Mater. Technol. 31, 32–37 (2016).10.1179/1753555715Y.0000000023 ↗
30. Fernandes, I. J. et al. Silver nanoparticle conductive inks: synthesis, characterization, and fabrication of inkjet-printed flexible electrodes. Sci. Rep. 10 (2020).10.1038/s41598-020-65698-3 ↗
31. Hussain, A. et al. Temperature Estimation during Pulsed Laser Sintering of Silver Nanoparticles. Appl. Sci. 12, 3467 (2022).10.3390/app12073467 ↗
32. Merilampi, S., Laine-Ma, T. & Ruuskanen, P. The characterization of electrically conductive silver ink patterns on flexible substrates. Microelectron. Reliab. 49, 782–790 (2009).10.1016/j.microrel.2009.04.004 ↗
33. Yang, M. et al. Mechanical and environmental durability of roll-to-roll printed silver nanoparticle film using a rapid laser annealing process for flexible electronics. Microelectron. Reliabil. 54 (2014).10.1016/j.microrel.2014.07.004 ↗
34. Cai, Y. et al. Large-scale and facile synthesis of silver nanoparticles via a microwave method for a conductive pen. RSC Adv. 7, 34041–34048 (2017).10.1039/C7RA05125E ↗
35. Li, C. et al. A two-step method to prepare silver nanoparticles ink for improving electrical and mechanical properties of printed silver wire. Mater. Express 11, 516–523 (2021).
36. Mo, L. et al. Silver Nanoparticles Based Ink with Moderate Sintering in Flexible and Printed Electronics. Int. J. Mol. Sci. 20, 2124 (2019).10.3390/ijms20092124 ↗
37. Cantor, B. in The Equations of Materials Ch. 7, 141-161 (Oxford University Press, 2020).10.1093/oso/9780198851875.003.0007 ↗
38. Vollath, D., Fischer, F. D. & Holec, D. Surface energy of nanoparticles – influence of particle size and structure. Beilstein J. Nanotechnol. 9, 2265–2276 (2018).10.3762/bjnano.9.211 ↗
39. Babalola, B. J., Ayodele, O. O. & Olubambi, P. A. Sintering of nanocrystalline materials: Sintering parameters. Heliyon 9, e14070 (2023).10.1016/j.heliyon.2023.e14070 ↗
40. Kothari, N. C. The effect of particle size on sintering kinetics in alumina powder. J. Nucl. Mater. 17, 43–54 (1965).10.1016/0022-3115(65)90146-7 ↗
41. Demirskyi, D., Agrawal, D. & Ragula, A. A scaling law study of the initial stage of microwave sintering of iron spheres. Scr. Materialia 66, 323–326 (2012).10.1016/j.scriptamat.2011.11.017 ↗
42. Herring, C. Effect of Change of Scale on Sintering Phenomena. J. Appl. Phys. 21, 301–303 (1950).10.1063/1.1699658 ↗
43. Liu, Z. et al. Enhanced Electrical and Mechanical Properties of a Printed Bimodal Silver Nanoparticle Ink for Flexible Electronics. Phys. Status Solidi (A) 215, 1800007 (2018).10.1002/pssa.201800007 ↗
44. Lee, I., Kim, S., Yun, J., Park, I. & Kim, T.-S. Interfacial toughening of solution processed Ag nanoparticle thin films by organic residuals. Nanotechnology 23, 485704 (2012).10.1088/0957-4484/23/48/485704 ↗
45. Kim, B.-J. et al. Improving mechanical fatigue resistance by optimizing the nanoporous structure of inkjet-printed Ag electrodes for flexible devices. Nanotechnology 25, 125706 (2014).10.1088/0957-4484/25/12/125706 ↗
46. Huang, Y. et al. Study effects of particle size in metal nanoink for electrohydrodynamic inkjet printing through analysis of droplet impact behaviors. J. Manuf. Process. 56, 1270–1276 (2020).10.1016/j.jmapro.2020.04.021 ↗
47. Jiang, L. et al. High-Sensitivity Fully Printed Flexible BaTiO3- Based Capacitive Humidity Sensor for In-Space Manufacturing by Electrohydrodynamic Inkjet Printing. IEEE Sens. J. 24, 24659–24667 (2024).10.1109/JSEN.2024.3400248 ↗
48. Smits, F. M. Measurement of Sheet Resistivities with the Four-Point Probe. Bell Syst. Tech. J. 37, 711–718 (1958).10.1002/j.1538-7305.1958.tb03883.x ↗