On the development of the refiner mechanical pulping process – a review
Source abstract
Abstract
Abstract This paper is a review of the development of the mechanical pulping process with focus on refiner-based processes. The intention is to provide an overview of the trends and the major advances in the development of the mechanical pulping (MP) process. The focus is on the development of the entire MP process, rather than the refiner as such. However, when discussing the MP process development, it is inevitable to consider the development of the refiner unit operation briefly. Processes for printing papers based on softwood is mainly discussed, but board processes are discussed briefly as well.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Lignin and Wood Chemistry · Advanced Cellulose Research Studies · Biofuel production and bioconversion
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Holmen Paper , Norrköping , Sweden
Mid Sweden University , Sundsvall , Sweden
QualTech , Tyringe , Sweden
Michael Jackson Consulting Inc. , Vancouver , Canada
Funding
Stiftelsen för Kunskaps- och Kompetensutveckling
References (100+)
Show source-provided references
1. Ahrel, I. (1973) Actual mill experiences 1968–1973 from producing thermomechanical pulp and gained experiences how to optimize the process for different end uses. In: Int. Mech. Pulping Conf. Stockholm, Sweden, Pres. 20.
2. Ahrel, I., Bäck, I. (1970) Thermomechanical pulp at Rockhammar. In: EUCEPA, Proc. Symp. Mech. Pulp 83. Oslo, Norway. pp. 83–91.
3. Ämmälä, A. (2001) Fractionation of thermomechanical pulp in pressure screening. PhD thesis, University of Oulu, ISBN 951-42-5919-X.
4. Amiri, R., Beaulieu, S., Thompson, T., Frith, M. (2016) Optimization of the Mechanical Pulping Process and its Impact on Energy Consumption and Pulp Properties — Mill Investigation. In: Int. Mech. Pulping Conf. Jacksonville, USA. pp. 667–695.
5. Andersson, S. (2011) Low consistency refining of mechanical pulp – process conditions and energy efficiency. Thesis, Mid Sweden University, ISBN 978-91-86694-60-9.
6. Andersson, S., Sandberg, C., Engstrand, P. (2012) Comparison of mechanical pulps from two stage HC single disc and HC double disc – LC refining. Appita J. 65(1):57–62.
7. Aregger, H.J. (1997) The TMP system at Perlen using the RTS concept. In: Int. Mech. Pulping Conf. Stockholm, Sweden. pp. 251–255.
8. Aregger, H.J. (2001) Operation experience with single stage main line refining in RTS operation. In: Int. Mech. Pulping Conf. Helsinki, Finland. pp. 229–237.
9. Arnesjö, B., Dillén, S. (1975) Thermomechanical pulping at Hallsta papermill. In: Int. Mech. Pulping Conf., San Francisco, USA, Vol. 1. pp. 97–103.
10. Asplund, A. (1934) Method of manufacture of pulp, Patent 2,008,892, Sep 19, 1934.
11. Asplund, A. (1953) The origin and development of the Defibrator process. Sven. Papp.tidn. 56(14):550–558.
12. Asplund, A., Bystedt, I. (1973) Development of the thermo-mechanical pulping method. In: Int. Mech. Pulping Conf. Stockholm, Sweden, Pres. 15.
13. Asplund, P., Bäck, R., Åhlund, A., Gannå, A., Jonsson, S. (2009) Screening of TMP is an essential key process in Ortviken paper mill. In: Int. Mech. Pulping Conf. Sundsvall, Sweden. pp. 147–151.
14. Atack, D. (1972) On the characterization of pressurized refiner mechanical pulps. Sven. Papp.tidn. 75(3):89–94.10.1016/0014-4827(72)90523-X ↗
15. Atack, D., Heitner, C., Stationwala, M.I. (1977) Ultra high yield pulping of eastern black spruce. In: Int. Mech. Pulping Conf. Helsinki, Finland, Pres. 7.
16. Atack, D., Wood, P.N. (1973) On the high consistency operation of large double rotating disc refiners. In: Int. Mech. Pulping Conf. Stockholm, Sweden, Pres. 12.
17. Barnet, A.J., Leask, R., Shaw, A.C. (1980) The OPCO process – Part I and II. Pulp Pap. Can. 81(10):T255–T260.
18. Beath, L.R. (1971) Groundwood rejects refining: Shive Reduction – specific energy relationships. In: CPPA Technical Section Proceedings, D92–D95.
19. Beath, L.R., Mihelich, W.G., Beaulieu, S.B., Wild, D.J. (1973) The use of sodium sulphite as an additive in the manufacture of refiner groundwood. In: Int. Mech. Pulping Conf. Stockholm, Sweden, Pres. 21.
20. Beath, L.R., Neill, M.T., Masse, F.A. (1966) Latency in mechanical wood pulps. Pulp Pap. Mag. Can. October:T423–T430.
21. Becker, H., Höglund, H., Tistad, G. (1977) Frequency and temperature in chip refining. Pap. Puu 59(3):123–130.
22. Bergström, J., Fredriksson, B., Sundelin, G. (1970) Recent developments in refiner groundwood manufacture at Ortviken. In: Symposium on mechanical pulp, Oslo, Norway. pp. 93–104.
23. Blanchard, P., Fontebasso, J. (1993) Mill implementation of a Freeness – Specific Energy control strategy for high consistency refiners. In: Int. Mech. Pulping Conf. Oslo, Norway. pp. 215–244.
24. Bonham, J.S., Flowers, A.G., Schofield, A.J. (1983) Post refining of P-radiata TMP. Appita J. 36(6):466–470.10.1093/oxfordjournals.pa.a051907 ↗
25. Bousquet, J.P., Villeneuve, J., Weber, M., Hogan, D. (2016) Summary of ISS conversion at the Grenada Resolute TMP mill. In: Int. Mech. Pulping Conf. Jacksonville, USA. pp. 780–786.
26. Brandal, J., Hauan, S. (1970) Postrefining of different types of groundwood pulps. Nor. Skogind. 10:313–325.
27. Butcher, C.E. (1975) The status of thermomechanical pulping operations at Pejepscot. In: Int. Mech. Pulping Conf. San Francisco, USA, Vol. 2. pp. 31–34.
28. Cannell, E. (1999) Pulp Screening Advancements Reduce Shives, Boost Quality. Pulp Pap. June 1999. pp.
29. Carpenter, C.H. The history of mechanical pulping. Tappi Mechanical Pulping Committee, Walker Printing Company, Montgomery, Alabama, USA, 1989.
30. Chapman, D.L.T., Allan, R.S. (1970) Some basic considerations in groundwood rejects refining. Pulp Pap. Mag. Can. T171–T176.
31. Charters, M.T., Ward, R.O. (1973) Elevated temperature refining for high quality mechanical pulp. In: Int. Mech. Pulping Conf. Stockholm, Sweden, Pres. 16.
32. Cochrane, J.A., Crotogino, H.F. (1965) Refiner groundwood from western Canadian woods. In: CPPA Technical Section Proceedings. pp. T388–T392.
33. Corson, S.R., Lee, M.J. (1990) Radiata pine TMP requires effective long fibre enhancement for good printability. Appita J. 43(4):277–282.
34. Corson, S.R., Wakelin, R.F. Lloyd, M.D. (1995) TMP Furnish development strategies for contrasting fibre types. In: Int. Mech. Pulping Conf. Ottawa, Canada. pp. 189–195.
35. Cort, J.B., Cort, C.J., Bohn, W.L. (1991) Controlled intensity refining: energy savings while maintaining pulp quality. In: TAPPI Pulping Conf. Orlando, USA. pp. 723–735.
36. Costantino, J., Fisher, D.J. (1983) Sodium sulfite treatment of west coast softwood in thermomechanical pulping. In: Int. Mech. Pulping Conf. Washington, USA. pp. 249–258.
37. Dahlqvist, G., Ferrari, B. (1981) Mill operating experience with a TMP refiner control system based on true disc clearance measurement. In: Int. Mech. Pulping Conf. Oslo, Norway, Session 3(6).
38. de Montmorency, W.H., Koller, E. (1957) Refining groundwood rejects with a double-disc refiner. In: Pulp Pap. Mag. Can. Convention Issue:206–226.
39. Dillén, S., Forsberg, E., Marklund, K., Minge, S. (1973) Groundwood fractionation in a conventional screening system and its influence on quality. In: Int. Mech. Pulping Conf. Stockholm, Sweden, Pres. 26.
40. Dorland, R.M., Holder, D.A., Leask, R.A., McKinney, J.W. (1962) Mechanical pulp from chips – Laboratory refining of softwood and hardwood. Tappi J. 45(4):257–265.
41. Eberhardt, L. (1955) New and revolutionary method for production of mechanical pulp- Groundwood from wood chips. Pap. Trade J. 139(37):26–28.
42. Edwards, J. (1964) Mechanical Pulping: Past, Present and Future. In: CPPA Annual Meeting Proceedings, Montreal, Canada. pp. T76–T78.
43. Engstrand, B., Sveningsson, P.-A., Sundblad, P., Wedin, P.-O. (1987) Ortviken – The uncommon paper mill. In: Int. Mech. Pulping Conf. Vancouver, Canada. pp. 91–97.
44. Evans, J.C.W. (1956) How Gould Paper pioneered most significant pulping process of century. Pap. Trade J. November:24–28.
45. Falk, B., Jackson, M., Danielsson, O. (1987) The use of single and double disc refiner configurations for the production of TMP for filled super calendered and light weight coated grades. In: Int. Mech. Pulping Conf. Vancouver, Canada. pp. 137–143.
46. Ferluc, A., Lanouette, R., Bousquet, J.-P., Bussières, S. (2010) Optimum refining of TMP pulp by fractionation after the first refining stage. Appita J. 63(4):308–314.
47. Ferritsius, O., Mörseburg, K., Ferritsius, R. (2014) BAT of CTMP and TMP plants with respect to quality development and energy efficiency. In: Int. Mech. Pulping Conf. Helsinki, Finland.
48. Ferritsius, R. (2019) Personal information.
49. Ferritsius, O., Ferritsius, R. (1997) Improved quality control and process design in production of mechanical pulp by the use of factor analysis. In: Int. Mech. Pulping Conf. Stockholm, Sweden, pp. 111–125.
50. Ferritsius, R., Sandberg, C., Ferritsius, O., Rundlöf, M., Daniel, G., Mörseburg, K., Fernando, D. (2016) Development of fiber properties in full scale HC and LC refining. In: Int. Mech. Pulping Conf. Jacksonville, USA. pp. 609–628.
51. Fjerdingen, H., Forseth, T.F., Gregersen, Ø.W., Helle, T., Johnsen, P.O., Kure, K.-A., Reme, P.A. (1997) Some Mechanical Pulp Fibre Characteristics, Their Process Relationships and Papermaking Significance. Transactions of the 11th Fundamental Research Symposium. In: The Fundamentals of Papermaking Materials, Cambridge, UK, Vol. 1. pp. 547–605.10.15376/frc.1997.1.547 ↗
52. Fournier, M., Ma, H., Shallhorn, P.M., Roche, A.A. (1991) Control of chip refiner operation. In: Int. Mech. Pulping Conf. Minneapolis, USA. pp. 91–100.
53. Franzen, R.G. (1983) LFCMP for high grading of mechanical pulps. In: Int. Mech. Pulping Conf. Washington, USA. pp. 297–311.
54. Franzén, R. (1986) General and selective upgrading of mechanical pulps. Nord. Pulp Pap. Res. J. 1(3):4–13.10.3183/npprj-1986-01-03-p004-013 ↗
55. Friesen, T. Bourdet, N., Tuomela, P., Allison, B., Olson, J. (2003) Pressure screen system simulation for optimal fractionation. Pulp Pap. Can. 104(4):43–48.
56. Gao, J. (2014) Modelling latency removal in mechanical pulping processes. PhD thesis, Dept. Chemical and Biological Engineering, Univ. of British Columbia, Vancouver, Canada.
57. Gardiner, E., Stafford, R. (1955) Low consistency refining of groundwood rejects at the Spruce Falls Power and Paper company Limited. Pulp Pap. Mag. Can. 56(12):163–165.
58. Gavelin, G. (1980) A single TMP furnish – the Monopulp process. Pulp Pap. Int. 22(13):54–56.
59. Gavelin, N.G. Science and Technology of Mechanical Pulp Manufacture. Lockwood, New York, 1966. pp. 190–218.
60. Gorski, D., Hill, J., Engstrand, P., Johansson, L. (2010) Review: Reduction of energy consumption in TMP refining through mechanical pre-treatment of wood chips. Nord. Pulp Pap. Res. J. 25(2):156–161.10.3183/npprj-2010-25-02-p156-161 ↗
61. Guangdong, Y., Xu, E.C., Jozic, D., Fitz, M. (2011) P-RC APMP lines at SUN paper group. In: Int. Mech. Pulping Conf. Xian, China. pp. 165–169.
62. Gummerus, M. (1983) Possibilities of upgrading TMP by sulphite treatment of the screen rejects. Pap. Puu 65(4):216–223.
63. Gustafsson, H., Vihmari, P. (1977) Viewpoints on screening and cleaning of mechanical pulps. In: Int. Mech. Pulping Conf. Helsinki, Finland, Pres. 41.
64. Hartler, N. (1977) Influence of chip moisture in mechanical pulping. In: Int. Mech. Pulping Conf. Helsinki, Finland, Pres. 6.
65. Hautala, J., Hourula, I., Jussila, T., Pitkänen, M. Mechanical Pulping. Papermaking Science and Technology Book 5. Ed. Sundholm, J. Fapet Oy, Jyväskylä, Finland, TAPPI press, 1999. pp. 252–286. ISBN 952-5216-05-5.
66. Heikkurinen, A., Vaarasalo, J., Karnis, A. (1993) Effect of initial defiberization on the properties of refiner mechanical pulp. J. Pulp Pap. Sci. 19(3):119–124.
67. Heitner, C., Atack, D., Karnis, A. (1982) Ultra-high yield pulping of eastern black spruce Part 3. Interstage sulfonation. Sven. Papp.tidn. 85(12):78–86.
68. Higgins, H.G., Irvine, G.M., Puri, V., Wardrop, A.B. (1978) Conditions for obtaining optimum properties of radiata and slash pine thermomechanical and chemithermomechanical pulps. Appita J. 32(1):23–33.
69. Hill, J., Johansson, L., Sabourin, M., Aichinger, J. (2009) Enhancing fiber development at reduced energy consumption using TMP sub-processes and targeted chemical application – Pilot and commercial scale results. In: Int. Mech. Pulping Conf. Sundsvall, Sweden. pp. 36–45.
70. Hofmann, D.A. (1975) Mechanical pulp cleaning. In: Int. Mech. Pulping Conf. San Francisco, USA, Vol. II. pp. 51–53.
71. Hoholik, F.S. (1958) Coarse grinding followed by refining. Pulp Pap. Mag. Can. 59(10):141–146.
72. Holzer, W.F., Henderson, J.T., West, W.B., Byington, K.F. (1962) The development and production of disc-refined groundwood pulp. Tappi J. 45(3):208–213.
73. Hooper, A.W. (1987) A comparison of slots and holes in the screening of mechanical pulp. In: CPPA Annual Meeting Proceedings, Montreal, Canada, pp. A249–256.
74. Huusari, E., Syrjänen, A. (1977) A new TMP process concept after two years intensive work. Pap. Puu 59(5):408–409.
75. Huusari, E., Syrjänen, A. (1981) Start-up experiences with the new tandem TMP heat recovery system at Kaipola. In: Int. Mech. Pulping Conf. Oslo, Norway, Session, 6(4).
76. Härkönen, E.J., Heikkurinen, A.M., Nederström, R. (1989) Comparison between different species of softwood as TMP raw material. In: Int. Mech. Pulping Conf, Helsinki, Finland. pp. 390–397.
77. Höglund, H., Bäck, R., Falk, B., Jackson, M. (1997) Thermopulp – A new energy-efficient mechanical pulping process. Pulp Pap. Can. 98(6):82–89.
78. Imppola, A., Mörseburg, K., Johansson, L., Ertsås, P.A. (2013) Effects of inlet pulp quality and specific energy consumption in mill scale low-consistency refining of mechanical pulp. In: 8th International Fundamental Mechanical Pulp Research Seminar, Åre, Sweden. Mid Sweden University. pp. 21–23. ISBN 978-91-88527-66-0. FSCN report 2018:59.
79. Jackson, M., Williams, G.J. (1979) Factors limiting the strength characteristics of thermomechanical pulp. In: Int. Mech. Pulping Conf. Toronto, Canada. pp. 37–48.
80. Jackson, M., Åkerlund, G. (1983) The effect of preheating and refiner housing pressure on the quality characteristics of TMP and CTMP. In: Int. Mech. Pulping Conf. Washington, USA. pp. 233–240.
81. Johansson, L., Hill, J., Gorski, D., Axelsson, P. (2011) Improvement of energy efficiency in TMP refining by selective wood disintegration and targeted application of chemicals. Nord. Pulp Pap. Res. J. 26(1):31–46.10.3183/npprj-2011-26-01-p031-046 ↗
82. Jones, H.W.H. (1968) Consolidated-Bathurst experimental refinedwood plant, A progress report. In: Int. Mech. Pulping Conf. Atlanta, USA, Session 7(6).
83. Jussila, T., Tienvieri, T., Sundholm, J. (1999) Flowsheets for various paper grades. In: Mechanical Pulping, Papermaking Science and Technology Book 5. Ed. Sundholm, J., Fapet Oy, Jyväskylä, Finland, TAPPI press. pp. 252–286. ISBN 952-5216-05-5.
84. Karlström, A., Hill, J., Johansson, L. (2018) An overview of some efforts to understand CD-refiners. In: Int. Mech. Pulping Conf. Trondheim, Norway, Session 7(1).
85. Karnis, A. (1979) Rapid method for liberating the latent properties of mechanical pulps. US.4,361,464, Nov. 30 1982.
86. Karnis, A. (1982) Refining of mechanical pulp rejects. Pap. Puu 64(4):57–272.
87. Kilpper, W., Baumgartner, W. (1977) Methods of improving the printability properties of TMP. In: Int. Mech. Pulping Conf. Helsinki, Finland, Pres. 18.
88. Klemm, K.H. Modern methods of mechanical pulp manufacture. Lockwood Trade Journal Co., Inc., New York, 1957.
89. Kurdin, J.A. (1974) Post refining of mechanical pulps for improving printing grades. Pulp Pap. Can. March:92–94.
90. Kurdin, J.A. (June 1979) Can energy costs for TMP and RMP be reduced? Pap. Trade J. 15:23–27.
91. Kure, K.-A. (2018) Keynote speech at IMPC. Trondheim, Not in Proceedings.
92. Kure, K.-A., Dahlqvist, G., Ekström, J., Helle, T. (1999) Hydrocyclone separation, and reject refining, of thick-walled mechanical pulp fibres. Nord. Pulp Pap. Res. J. 14(2):100–110.10.3183/npprj-1999-14-02-p100-104 ↗
93. Lansford, J.L. (1979) Rejects refining and bleaching of mechanical pulp. In: Int. Mech. Pulping Conf. Toronto, Canada. pp. 323–329.
94. Leask, R. (1989) 14th Mechanical pulping survey, Designed refiner capacity of TMP, CTMP, BCTMP, TCMP and SCMP reaches 82 000 t/d. Pulp Pap. Can. 90(3):22–32.
95. Levlin, J.-E. (1980) Effect of beating on paper making properties of high yield pulps. Pulp Pap. Can. 81(12):TR94–TR98.
96. Lewis, J., Danforth, D.W. (1962) Stock preparation analysis. Tappi J. 45(3):185–188.
97. Lindholm, C.A. (1979) Strengthening of groundwood pulp through chemical post-treatment. Pap. Puu 61(3):141–150.
98. Luhde, F. (1966) Low-energy refiner pulp production by two-stage high-consistency refining with interstage screening. In: CPPA Technical Section Proceedings. pp. T509–T518.
99. Luukkonen, A. (2007) Development of a methodology to optimize low consistency refining of mechanical pulp. PhD Thesis, University of British Columbia.
100. Mackie, D.M., Taylor, J.S. (1988) Review of the production and properties of alphabet pulps. Pulp Pap. Can. 89(2):T64–T72.