Current progress of research on heat-resistant Mg alloys: A review
Source abstract
Abstract
With the increasing attention received by lightweight metals, numerous essential fields have increased requirements for magnesium (Mg) alloys with good room-temperature and high-temperature mechanical properties. However, the high-temperature mechanical properties of commonly used commercial Mg alloys, such as AZ91D, deteriorate considerably with increasing temperatures. Over the past several decades, extensive efforts have been devoted to developing heat-resistant Mg alloys. These approaches either inhibit the generation of thermally unstable phases or promote the formation of thermally stable precipitates/phases in matrices through solid solution or precipitation strengthening. In this review, numerous studies are systematically introduced and discussed. Different alloy systems, including those based on Mg–Al, Mg–Zn, and Mg–rare earth, are carefully classified and compared to reveal their mechanical properties and strengthening mechanisms. The emphasis, limitations, and future prospects of these heat-resistant Mg alloys are also pointed out and discussed to develop heat-resistant Mg alloys and broaden their potential application areas in the future.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Hydrogen Storage and Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (100+)
Show source-provided references
1. H.T. Jeong and W.J. Kim, The hot compressive deformation behavior of cast Mg–Gd–Y–Zn–Zr alloys with and without LPSO phase in their initial microstructures, J. Magnes. Alloys, 10(2022), No. 10, p. 2901.10.1016/j.jma.2022.01.006 ↗
2. W.J. Yin, F. Briffod, T. Shiraiwa, and M. Enoki, Mechanical properties and failure mechanisms of Mg–Zn–Y alloys with different extrusion ratio and LPSO volume fraction, J. Magnes. Alloys, 10(2022), No. 8, p. 2158.10.1016/j.jma.2022.02.004 ↗
3. J.H. Zhang, S.J. Liu, R.Z. Wu, L.G. Hou, and M.L. Zhang, Recent developments in high-strength Mg–RE-based alloys: Focusing on Mg–Gd and Mg–Y systems, J. Magnes. Alloys, 6(2018), No. 3, p. 277.10.1016/j.jma.2018.08.001 ↗
4. M.F. Qi, L.Y. Wei, Y.Z. Xu, et al., Effect of trace yttrium on the microstructure, mechanical property and corrosion behavior of homogenized Mg–2Zn–0.1Mn–0.3Ca–.xY biological magnesium alloy, Int. J. Miner. Metall. Mater., 29(2022), No. 9, p. 1746.10.1007/s12613-021-2327-x ↗
5. H.B. Liao, L.L. Mo, X. Zhou, Z.Z. Yuan, and J. Du, Revealing the nucleation event of Mg–Al alloy induced by Fe impurity, Int. J. Miner. Metall. Mater., 29(2022), No. 7, p. 1317.10.1007/s12613-021-2406-z ↗
6. M. Pekguleryuz and M. Celikin, Creep resistance in magnesium alloys, Int. Mater. Rev., 55(2010), No. 4, p. 197.10.1179/095066010X12646898728327 ↗
7. A.A. Luo, Recent magnesium alloy development for elevated temperature applications, Int. Mater. Rev., 49(2004), No. 1, p. 13.10.1179/095066004225010497 ↗
8. M.O. Pekguleryuz and A.A. Kaya, Creep resistant magnesium alloys for powertrain applications, Adv. Eng. Mater., 5(2003), No. 12, p. 866.10.1002/adem.200300403 ↗
9. K.R. Athul, U.T.S. Pillai, A. Srinivasan, and B.C. Pai, A review of different creep mechanisms in Mg alloys based on stress exponent and activation energy, Adv. Eng. Mater., 18(2016), No. 5, p. 770.10.1002/adem.201500393 ↗
10. K.U. Kainer, Y.D. Huang, H. Dieringa, and N. Hort, Status of the development of creep resistant magnesium materials for automotive applications, Mater. Sci. Forum, 638–642(2010), p. 73.10.4028/www.scientific.net/MSF.638-642.73 ↗
11. D.H. Zhang, S.C. Zhao, C.L. Wang, et al., Achieving enhanced high-temperature mechanical properties in Mg–Nd–Sm–Zn–Ca–Zr alloy by Ag addition, Mater. Today Commun., 31(2022), art. No. 103666.10.1016/j.mtcomm.2022.103666 ↗
12. D.H. Zhang, S.C. Zhao, H.T. Chen, Y.C. Feng, E.J. Guo, and J.F. Li, Microstructure and mechanical properties of EK30 alloy synergistically reinforced by Ag alloying and hot extrusion for aerospace applications, Materials, 15(2022), No. 23, art. No. 8613.10.3390/ma15238613 ↗
13. Z.H. Chen, Heat-Resistant Mg Alloys, Chemical Industry Press, Beijing, 2007.
14. B.Z. Yin, J.G. Liu, B. Peng, et al., Influence of layer thickness on formation quality, microstructure, mechanical properties, and corrosion resistance of WE43 magnesium alloy fabricated by laser powder bed fusion, J. Magnes. Alloys, 12(2024), No. 4, p. 1376.
15. N. Mo, Q.Y. Tan, M. Bermingham, et al., Current development of creep-resistant magnesium cast alloys: A review, Mater. Des., 155(2018), p. 422.10.1016/j.matdes.2018.06.032 ↗
16. Z.P. Yu, Y.H. Yan, J. Yao, et al., Effect of tensile direction on mechanical properties and microstructural evolutions of rolled Mg–Al–Zn–Sn magnesium alloy sheets at room and elevated temperatures, J. Alloys Compd., 744(2018), p. 211.10.1016/j.jallcom.2018.01.344 ↗
17. H. Wang, C.J. Boehlert, Q.D. Wang, D.D. Yin, and W.J. Ding, In-situ analysis of the tensile deformation modes and anisotropy of extruded Mg–10Gd–3Y–0.5Zr (wt.%) at elevated temperatures, Int. J. Plast., 84(2016), p. 255.10.1016/j.ijplas.2016.06.001 ↗
18. A. Chapuis and J.H. Driver, Temperature dependency of slip and twinning in plane strain compressed magnesium single crystals, Acta Mater., 59(2011), No. 5, p. 1986.10.1016/j.actamat.2010.11.064 ↗
19. J.H. Cui, H. Yang, Y.X. Zhou, et al., Optimizing the microstructures and enhancing the mechanical properties of AZ81 alloy by adding TC4 particles, Mater. Sci. Eng. A, 863(2023), art. No. 144518.10.1016/j.msea.2022.144518 ↗
20. S.H. Lu, D. Wu, R.S. Chen, and E. Han, The influence of temperature on twinning behavior of a Mg–Gd–Y alloy during hot compression, Mater. Sci. Eng. A, 735(2018), p. 173.10.1016/j.msea.2018.08.004 ↗
21. J. Čapek, G. Farkas, J. Pilch, and K. Máthis, Temperature dependence of twinning activity in random textured cast magnesium, Mater. Sci. Eng. A, 627(2015), p. 333.10.1016/j.msea.2015.01.017 ↗
22. Z.J. Yu, Y.D. Huang, H. Dieringa, et al., High temperature mechanical behavior of an extruded Mg–11Gd–4.5Y–1Nd–1.5Zn–0.5Zr (wt%) alloy, Mater. Sci. Eng. A, 645(2015), p. 213.10.1016/j.msea.2015.08.001 ↗
23. H. Yang, S. Gavras, and H. Dieringa, Creep characteristics of metal matrix composites, [in] D. Brabazon, ed., Encyclopedia of Materials: Composites, Vol. 1, Elsevier, Amsterdam, 2021, p. 375.10.1016/B978-0-12-803581-8.11822-3 ↗
24. H. Yang, X.H. Chen, G.S. Huang, et al., Microstructures and mechanical properties of titanium-reinforced magnesium matrix composites: Review and perspective, J. Magnes. Alloys, 10(2022), No. 9, p. 2311.10.1016/j.jma.2022.07.008 ↗
25. M. Mabuchi and K. Higashi, Strengthening mechanisms of Mg–Si alloys, Acta Mater., 44(1996), No. 11, p. 4611.10.1016/1359-6454(96)00072-9 ↗
26. T. Dessolier, P. Lhuissier, F. Roussel-Dherbey, et al., Effect of temperature on deformation mechanisms of AZ31 Mg-alloy under tensile loading, Mater. Sci. Eng. A, 775(2020), art. No. 138957.10.1016/j.msea.2020.138957 ↗
27. D.J. Zhai, X.P. Li, and J. Shen, Mechanism of microarc oxidation on AZ91D alloy induced by β-Mg17Al12 phase, Int. J. Miner. Metall. Mater., 31(2024), No. 4, p. 712.10.1007/s12613-023-2752-0 ↗
28. J. Han, C. Wang, Y.M. Song, Z.Y. Liu, J.P. Sun, and J.Y. Zhao, Simultaneously improving mechanical properties and corrosion resistance of as-cast AZ91 Mg alloy by ultrasonic surface rolling, Int. J. Miner. Metall. Mater., 29(2022), No. 8, p. 1551.10.1007/s12613-021-2294-2 ↗
29. Y.H. Chen, L.P. Wang, Y.C. Feng, E.J. Guo, S.C. Zhao, and L. Wang, Effect of Ca and Sm combined addition on the microstructure and elevated-temperature mechanical properties of Mg–6Al alloys, J. Mater. Eng. Perform., 28(2019), No. 5, p. 2892.10.1007/s11665-019-04044-9 ↗
30. J.S. Miao, W.H. Sun, A.D. Klarner, and A.A. Luo, Interphase boundary segregation of silver and enhanced precipitation of Mg17Al12 phase in a Mg–Al–Sn–Ag alloy, Scripta Mater., 154(2018), p. 192.10.1016/j.scriptamat.2018.05.047 ↗
31. K. Korgiopoulos, B. Langelier, and M. Pekguleryuz, Mg17Al12 phase refinement and the improved mechanical performance of Mg–6Al alloy with trace erbium addition, Mater. Sci. Eng. A, 812(2021), art. No. 141075.10.1016/j.msea.2021.141075 ↗
32. P.P. Wang, H.T. Jiang, Y.J. Wang, et al., Role of trace additions of Ca and Sn in improving the corrosion resistance of Mg–3Al–1Zn alloy, Int. J. Miner. Metall. Mater., 29(2022), No. 8, p. 1559.10.1007/s12613-021-2268-4 ↗
33. K.M. Asl, A. Tari, and F. Khomamizadeh, The effect of different content of Al, RE and Si element on the microstructure, mechanical and creep properties of Mg–Al alloys, Mater. Sci. Eng. A, 523(2009), No. 1–2, p. 1.
34. A. Srinivasan, U.T.S. Pillai, and B.C. Pai, Microstructure and mechanical properties of Si and Sb added AZ91 magnesium alloy, Metall. Mater. Trans. A, 36(2005), No. 8, p. 2235.10.1007/s11661-005-0342-6 ↗
35. A. Srinivasan, U.T.S. Pillai, J. Swaminathan, S.K. Das, and B.C. Pai, Observations of microstructural refinement in Mg–Al–Si alloys containing strontium, J. Mater. Sci., 41(2006), No. 18, p. 6087.10.1007/s10853-006-0643-1 ↗
36. A. Srinivasan, K.K. Ajithkumar, J. Swaminathan, U.T.S. Pillai, and B.C. Pai, Creep behavior of AZ91 magnesium alloy, Procedia Eng., 55(2013), p. 109.10.1016/j.proeng.2013.03.228 ↗
37. J.H. Chen, Z.H. Chen, H.G. Yan, F.Q. Zhang, and K. Liao, Effects of Sn addition on microstructure and mechanical properties of Mg–Zn–Al alloys, J. Alloys Compd., 461(2008), No. 1–2, p. 209.
38. D.H. Kang, S.S. Park, and N.J. Kim, Development of creep resistant die cast Mg–Sn–Al–Si alloy, Mater. Sci. Eng. A, 413–414(2005), p. 555.10.1016/j.msea.2005.09.022 ↗
39. H.X. Li, W.J. Xu, Y.F. Zhang, et al., Prediction of the thermal conductivity of Mg–Al–La alloys by CALPHAD method, Int. J. Miner. Metall. Mater., 31(2024), No. 1, p. 129.10.1007/s12613-023-2759-6 ↗
40. J.S. Xie, Z. Zhang, S.J. Liu, et al., Designing new low alloyed Mg–RE alloys with high strength and ductility via high-speed extrusion, Int. J. Miner. Metall. Mater., 30(2023), No. 1, p. 82.10.1007/s12613-022-2472-x ↗
41. T.T. Zhang, W.B. Yu, C.S. Ma, W.T. Chen, L. Zhang, and S.M. Xiong, The effect of different high pressure die casting parameters on 3D microstructure and mechanical properties of AE44 magnesium alloy, J. Magnes. Alloys, 11(2023), No. 9, p. 3141.10.1016/j.jma.2022.05.001 ↗
42. R. Mahmudi, F. Kabirian, and Z. Nematollahi, Microstructural stability and high-temperature mechanical properties of AZ91 and AZ91+2RE magnesium alloys, Mater. Des., 32(2011), No. 5, p. 2583.10.1016/j.matdes.2011.01.040 ↗
43. X.X. Dong, L.Y. Feng, S.H. Wang, E.A. Nyberg, and S.X. Ji, A new die-cast magnesium alloy for applications at higher elevated temperatures of 200–300 °C, J. Magnes. Alloys, 9(2021), No. 1, p. 90.10.1016/j.jma.2020.09.012 ↗
44. I.A. Anyanwu, Y. Gokan, A. Suzuki, et al., Effect of substituting cerium-rich mischmetal with lanthanum on high temperature properties of die-cast Mg–Zn–Al–Ca–RE alloys, Mater. Sci. Eng. A, 380(2004), No. 1–2, p. 93.10.1016/j.msea.2004.03.039 ↗
45. T. Homma, S. Hirawatari, H. Sunohara, and S. Kamado, Room and elevated temperature mechanical properties in the as-extruded Mg–Al–Ca–Mn alloys, Mater. Sci. Eng. A, 539(2012), p. 163.10.1016/j.msea.2012.01.074 ↗
46. A. Suzuki, N.D. Saddock, J.W. Jones, and T.M. Pollock, Solidification paths and eutectic intermetallic phases in Mg–Al–Ca ternary alloys, Acta Mater., 53(2005), No. 9, p. 2823.10.1016/j.actamat.2005.03.001 ↗
47. Z. Zhang, A. Couture, and A. Luo, An investigation of the properties of Mg–Zn–Al alloys, Scripta Mater., 39(1998), No. 1, p. 45.10.1016/S1359-6462(98)00122-5 ↗
48. B. Tang, J.L. Fu, J.K. Feng, X.T. Zhong, Y.Y. Guo, and H.L. Wang, Effect of Zn content on microstructure, mechanical properties and thermal conductivity of extruded Mg–Zn–Ca–Mn alloys, Int. J. Miner. Metall. Mater., 30(2023), No. 12, p. 2411.10.1007/s12613-023-2676-8 ↗
49. K. Yang, H.C. Pan, S. Du, et al., Low-cost and high-strength Mg–Al–Ca–Zn–Mn wrought alloy with balanced ductility, Int. J. Miner. Metall. Mater., 29(2022), No. 7, p. 1396.10.1007/s12613-021-2395-y ↗
50. W.Q. Zhang, W.L. Xiao, F. Wang, and C.L. Ma, Development of heat resistant Mg–Zn–Al-based magnesium alloys by addition of La and Ca: Microstructure and tensile properties, J. Alloys Compd., 684(2016), p. 8.10.1016/j.jallcom.2016.05.137 ↗
51. W.F. Mo, L. Zhang, G.H. Wu, Y. Zhang, W.C. Liu, and C.L. Wang, Effects of processing parameters on microstructure and mechanical properties of squeeze-cast Mg–12Zn–4Al–0.5Ca alloy, Mater. Des., 63(2014), p. 729.10.1016/j.matdes.2014.07.005 ↗
52. S.M. Zhu, M.A. Easton, T.B. Abbott, et al., Evaluation of magnesium die-casting alloys for elevated temperature applications: Microstructure, tensile properties, and creep resistance, Metall. Mater. Trans. A, 46(2015), No. 8, p. 3543.10.1007/s11661-015-2946-9 ↗
53. W.L. Xiao, Y.S. Shen, L.D. Wang, et al., The influences of rare earth content on the microstructure and mechanical properties of Mg–7Zn–5Al alloy, Mater. Des., 31(2010), No. 7, p. 3542.10.1016/j.matdes.2010.01.046 ↗
54. X. Gao and J.F. Nie, Characterization of strengthening precipitate phases in a Mg–Zn alloy, Scripta Mater., 56(2007), No. 8, p. 645.10.1016/j.scriptamat.2007.01.006 ↗
55. C.J. Bettles, M.A. Gibson, K. Venkatesan, Enhanced age-hardening behaviour in Mg–4 wt.% Zn micro-alloyed with Ca, Scripta Mater., 51(2004), No. 3, p. 193.10.1016/j.scriptamat.2004.04.020 ↗
56. S. Farahany, H.R. Bakhsheshi-Rad, M.H. Idris, M.R.A. Kadir, A.F. Lotfabadi, and A. Ourdjini, In-situ thermal analysis and macroscopical characterization of Mg–xCa and Mg–0.5Ca–xZn alloy systems, Thermochim. Acta, 527(2012), p. 180.10.1016/j.tca.2011.10.027 ↗
57. F. Naghdi, R. Mahmudi, J.Y. Kang, and H.S. Kim, Microstructure and high-temperature mechanical properties of the Mg–4Zn–0.5Ca alloy in the as-cast and aged conditions, Mater. Sci. Eng. A, 649(2016), p. 441.10.1016/j.msea.2015.10.011 ↗
58. Y. Ishiguro, X.S. Huang, Y. Tsukada, T. Koyama, and Y. Chino, Effect of bending and tension deformation on the texture evolution and stretch formability of Mg–Zn–RE–Zr alloy, Int. J. Miner. Metall. Mater., 29(2022), No. 7, p. 1334.10.1007/s12613-021-2398-8 ↗
59. N. Tahreen and D.L. Chen, A critical review of Mg–Zn–Y series alloys containing I, W, and LPSO phases, Adv. Eng. Mater., 18(2016), No. 12, p. 1983.10.1002/adem.201600393 ↗
60. Z.C. Xu, C. Zhu, X.F. Guo, W.P. Yang, H.B. Cui, and Y. Wang, Effect of multi-pass equal channel angular pressing on the microstructure and mechanical properties of a directional solidification Mg98.5Zn0.5Y1 alloy, Mater. Trans., 60(2019), No. 11, p. 2361.10.2320/matertrans.M2019088 ↗
61. M. Mehrabi-Mehdiabadi and R. Mahmudi, Effects of yttrium addition on microstructural stability and elevated-temperature mechanical properties of a cast Mg–Zn alloy, J. Alloys Compd., 820(2020), art. No. 153083.10.1016/j.jallcom.2019.153083 ↗
62. J.F. Nie, Precipitation and hardening in magnesium alloys, Metall. Mater. Trans. A, 43(2012), No. 11, p. 3891.10.1007/s11661-012-1217-2 ↗
63. S. Yuan, J.H. Wang, X.Q. Li, H.B. Ma, L. Zhang, and P.P. Jin, Enhanced mechanical properties of Mg–1Al–12Y alloy containing long period stacking ordered phase, J. Magnes. Alloys, 11(2023), No. 12, p. 4679.10.1016/j.jma.2022.03.005 ↗
64. N. Hort, Y. Huang, and K.U. Kainer, Intermetallics in magnesium alloys, Adv. Eng. Mater., 8(2006), No. 4, p. 235.10.1002/adem.200500202 ↗
65. T.L. Chia, M.A. Easton, S.M. Zhu, M.A. Gibson, N. Birbilis, and J.F. Nie, The effect of alloy composition on the microstructure and tensile properties of binary Mg–rare earth alloys, Intermetallics, 17(2009), No. 7, p. 481.10.1016/j.intermet.2008.12.009 ↗
66. J.H. Zhang, H.F. Liu, W. Sun, H.Y. Lu, D.X. Tang, and J. Meng, Influence of structure and ionic radius on solubility limit in the Mg–RE systems, Mater. Sci. Forum, 561–565(2007), p. 143.
67. J. Wang, L. Luo, Q.H. Huo, et al., Creep behaviors of a highly concentrated Mg–18 wt%Gd binary alloy with and without artificial aging, J. Alloys Compd., 774(2019), p. 1036.10.1016/j.jallcom.2018.10.013 ↗
68. H.Y. Guo, S.H. Liu, L. Huang, D.Q. Wang, Y. Du, and M.Q. Chu, Thermal conductivity of As-cast and annealed Mg–RE binary alloys, Metals, 11(2021), No. 4, art. No. 554.10.3390/met11040554 ↗
69. S.M. Zhu, M.A. Gibson, M.A. Easton, and J.F. Nie, The relationship between microstructure and creep resistance in die-cast magnesium–rare earth alloys, Scripta Mater., 63(2010), No. 7, p. 698.10.1016/j.scriptamat.2010.02.005 ↗
70. D. Weiss, A.A. Kaya, E. Aghion, and D. Eliezer, Microstructure and creep properties of a cast Mg–1.7%wt rare earth–0.3%wt Mn alloy, J. Mater. Sci., 37(2002), No. 24, p. 5371.10.1023/A:1021001813867 ↗
71. L.Y. Feng, X.X. Dong, Q. Cai, B. Wang, and S.X. Ji, Effect of Nd on the microstructure and mechanical properties of Mg–La–Ce alloys at ambient and elevated temperatures, J. Mater. Eng. Perform., 32(2023), No. 6, p. 2598.10.1007/s11665-022-06853-x ↗
72. A.R. Natarajan, E.L.S. Solomon, B. Puchala, E.A. Marquis, and A.V. D Ven, On the early stages of precipitation in dilute Mg–Nd alloys, Acta Mater., 108(2016), p. 367.10.1016/j.actamat.2016.01.055 ↗
73. D.H. Ping, K. Hono, and J.F. Nie, Atom probe characterization of plate-like precipitates in a Mg–RE–Zn–Zr casting alloy, Scripta Mater., 48(2003), No. 8, p. 1017.10.1016/S1359-6462(02)00586-9 ↗
74. Y.Y. Zhou, P.H. Fu, L.M. Peng, et al., Precipitation modification in cast Mg–1Nd–1Ce–Zr alloy by Zn addition, J. Magnes. Alloys, 7(2019), No. 1, p. 113.10.1016/j.jma.2019.02.003 ↗
75. J.H. Jun, K.D. Seong, and M.H. Lee, Effect of zirconium on high temperature tensile properties of precipitation- hardened Mg–Nd–Zn casting alloy, Int. J. Mod. Phys. B, 23(2009), No. 06n07, p. 966.10.1142/S0217979209060312 ↗
76. S.H. Wang, J.L. Yang, J.Q. Pan, et al., Unveiling the mechanical response and deformation mechanism of extruded Mg–2.5Nd–0.5Zn–0.5Zr alloy sheet under high-temperature tensile, J. Alloys Compd., 911(2022), art. No. 164987.10.1016/j.jallcom.2022.164987 ↗
77. X.H. Shao, Z.Q. Yang, and X.L. Ma, Strengthening and toughening mechanisms in Mg–Zn–Y alloy with a long period stacking ordered structure, Acta Mater., 58(2010), No. 14, p. 4760.10.1016/j.actamat.2010.05.012 ↗
78. G. Garces, P. Perez, S. Cabeza, S. Kabra, W. Gan, and P. Adeva, Effect of extrusion temperature on the plastic deformation of an Mg–Y–Zn alloy containing LPSO phase using in situ neutron diffraction, Metall. Mater. Trans. A, 48(2017), No. 11, p. 5332.10.1007/s11661-017-4284-6 ↗
79. H. Liu, H. Huang, C. Li, and X.W. Yang, Effects of Y content on mechanical properties of extruded Mg–Y–Zn alloys at room and elevated temperatures, Ordnance Mater. Sci. Eng., 40(2017), No. 2, p. 34.
80. Z.L. Jin, Q.D. Wang, J. Zheng, and W.J. Ding, Effects of Y content on microstructure and properties of Mg–Y–Zn–Zr alloy, Spec. Cast. Nonferrous Alloys, 29(2009), No. 7, p. 656.
81. M. Sun, G.H. Wu, W. Wang, Z.Q. Hou, B. Chen, and W.J. Ding, Research progress of Mg–Gd alloy, Mater. Reports, 23(2009), No. 6, p. 98.
82. H.Z. Zhan, As-cast microstructures and properties of Mg–Gd alloy, Foundry Technol., 39(2018), No. 1, p. 54.
83. S.X. Ouyang, G.Y. Yang, H. Qin, C.H. Wang, S.F. Luo, and W.Q. Jie, Effect of the precipitation state on high temperature tensile and creep behaviors of Mg–15Gd alloy, J. Magnes. Alloys, 10(2022), No. 12, p. 3459.10.1016/j.jma.2021.06.016 ↗
84. K. Liu, J.H. Zhang, L.L. Rokhlin, F.M. Elkin, D.X. Tang, and J. Meng, Microstructures and mechanical properties of extruded Mg–8Gd–0.4Zr alloys containing Zn, Mater. Sci. Eng. A, 505(2009), No. 1–2, p. 13.10.1016/j.msea.2008.12.023 ↗
85. H. Li, W.B. Du, S.B. Li, and Z.H. Wang, Effect of Zn/Er weight ratio on phase formation and mechanical properties of as-cast Mg–Zn–Er alloys, Mater. Des., 35(2012), p. 259.10.1016/j.matdes.2011.10.002 ↗
86. S.J. Cui, H.R. Geng, X.Y. Teng, X.W. Wu, P. Jia, and C. Wu, Microstructure and mechanical properties of Mg–Er–Zn alloys with LPSO phase, Mater. Sci. Forum, 898(2017), p. 53.10.4028/www.scientific.net/MSF.898.53 ↗
87. L.X. Hong, R.X. Wang, and X.B. Zhang, Effects of Nd on microstructure and mechanical properties of as-cast Mg–12Gd–2Zn–xNd–0.4Zr alloys with stacking faults, Int. J. Miner. Metall. Mater., 29(2022), No. 8, p. 1570.10.1007/s12613-021-2264-8 ↗
88. L.D. Wang, C.Y. Xing, X.L. Hou, Y.M. Wu, J.F. Sun, and L.M. Wang, Microstructures and mechanical properties of as-cast Mg–5Y–3Nd–Zr–xGd (x = 0, 2 and 4wt.%) alloys, Mater. Sci. Eng. A, 527(2010), No. 7–8, p. 1891.10.1016/j.msea.2009.11.026 ↗
89. Z.L. Ning, J.Y. Yi, M. Qian, et al., Microstructure and elevated temperature mechanical and creep properties of Mg–4Y–3Nd–0.5Zr alloy in the product form of a large structural casting, Mater. Des., 60(2014), p. 218.10.1016/j.matdes.2014.03.062 ↗
90. R. Ma, S.H. Lv, Z.F. Xie, at al., Achieving high strength-ductility in a wrought Mg–9Gd–3Y–0.5Zr alloy by modifying with minor La addition, J. Alloys Compd., 884(2021), art. No. 161062.10.1016/j.jallcom.2021.161062 ↗
91. A. Movahedi-Rad and R. Mahmudi, Effect of Ag addition on the elevated-temperature mechanical properties of an extruded high strength Mg–Gd–Y–Zr alloy, Mater. Sci. Eng. A, 614(2014), p. 62.10.1016/j.msea.2014.07.022 ↗
92. X.H. Guan, W. Wang, T. Zhang, et al., A new insight into LPSO phase transformation and mechanical properties uniformity of large-scale Mg–Gd–Y–Zn–Zr alloy prepared by multi-pass friction stir processing, J. Magnes. Alloys, 2022. DOI: https://doi.org/10.1016/j.jma.2022.09.01710.1016/j.jma.2022.09.017 ↗
93. J.Y. Li, F.L. Wang, J. Zeng, et al., Decreasing the mechanical anisotropy of the forged Mg–8.5Gd–2.5Y–1.5Zn–0.5Zr alloy by modulating blocky LPSO particles using multi-directional forging, J. Magnes. Alloys, 2022. DOI: https://doi.org/10.1016/j.jma.2022.10.024.10.1016/j.jma.2022.10.024 ↗
94. S.M. He, X.Q. Zeng, L.M. Peng, X. Gao, J.F. Nie, and W.J. Ding, Precipitation in a Mg–10Gd–3Y–0.4Zr (wt.%) alloy during isothermal ageing at 250°C, J. Alloys Compd., 421(2006), No. 1–2, p. 309.
95. H.R.J. Nodooshan, G.H. Wu, W.C. Liu, G.L. Wei, Y.L. Li, and S. Zhang, Effect of Gd content on high temperature mechanical properties of Mg–Gd–Y–Zr alloy, Mater. Sci. Eng. A, 651(2016), p. 840.10.1016/j.msea.2015.11.047 ↗
96. J. Wang, J. Meng, D.P. Zhang, and D.X. Tang, Effect of Y for enhanced age hardening response and mechanical properties of Mg–Gd–Y–Zr alloys, Mater. Sci. Eng. A, 456(2007), No. 1–2, p. 78.
97. T. Homma, N. Kunito, and S. Kamado, Fabrication of extraordinary high-strength magnesium alloy by hot extrusion, Scripta Mater., 61(2009), No. 6, p. 644.10.1016/j.scriptamat.2009.06.003 ↗
98. X.L. Hou, Q.M. Peng, Z.Y. Cao, et al., Structure and mechanical properties of extruded Mg–Gd based alloy sheet, Mater. Sci. Eng. A, 520(2009), No. 1–2, p. 162.
99. Z.J. Yu, Y.D. Huang, X. Qiu, et al., Fabrication of magnesium alloy with high strength and heat-resistance by hot extrusion and ageing, Mater. Sci. Eng. A, 578(2013), p. 346.10.1016/j.msea.2013.04.108 ↗
100. Q.M. Peng, X.L. Hou, L.D. Wang, Y.M. Wu, Z.Y. Cao, and L.M. Wang, Microstructure and mechanical properties of high performance Mg–Gd based alloys, Mater. Des., 30(2009), No. 2, p. 292.10.1016/j.matdes.2008.04.069 ↗