Effect of cutting vibration on the surface quality of commercially pure titanium (TA2) based on rotor dynamics model analysis
Source abstract
Abstract
A dynamic model based on rotor dynamics was proposed to analyze the effect of workpiece-tool system vibration on the cutting accuracy of commercially pure titanium TA2. The proposed model considers the imbalance of mass and stiffness caused by material removal, regenerative chatter effect, the Johnson–Cook plastic material constitutive model of the workpiece, and coupled vibration between workpiece and tool. The differential equation of the rotating workpiece-tool system is derived by using D` Alembert`s principle. The model`s validity is verified by cutting tests and surface topography observation. Besides, the effects of different cutting parameters on cutting vibration characteristics and Processing quality are discussed. According to cutter-workpiece vibration response and the test results of surface roughness, chip morphology, and surface morphology, the causes of cutting vibration and the influence of cutting parameters on surface quality are revealed.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced machining processes and optimization · Advanced Surface Polishing Techniques · Engineering Technology and Methodologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Agrawal, C., Wadhwa, J., Pitroda, A., Pruncu, I., Khanna, N.: Comprehensive analysis of tool wear, tool life, surface roughness, costing and carbon emissions in turning Ti–6Al–4V titanium alloy: cryogenic versus wet machining. Tribol. Int. 153, 106597 (2020)10.1016/j.triboint.2020.106597 ↗
2. Anhai, L., Zhao, J.: Effect of cutting parameters and tool rake angle on the chip formation and adiabatic shear characteristics in machining Ti-6Al-4V titanium alloy. Int. J. Adv. Manuf. Technol. 107(7), 3077–3091 (2020)
3. Bashir, B.M., Wan, M., Liu, Y., Yuan, H.: Active damping of milling vibration using operational amplifier circuit. Chin. ChinJ. Mech. Eng-En. 31(5), 58–65 (2018)
4. Caixu, Y.U.E., Haining, G.A.O., Xianli, L.I.U., Steven, Y.L.I.A.N.G., Lihui, W.A.N.G.: A review of chatter vibration research in milling. Chin. J. Aeronaut. 32(2), 1–28 (2019)
5. Cedergren, S., Frangoudis, C., Archenti, A., Pederson, R., Sjöberg, G.: Influence of work material microstructure on vibrations when machining cast Ti-6AL-4V. Int. J. Adv. Manuf. Technol. 84, 2277–2291 (2016)10.1007/s00170-015-7827-2 ↗
6. Chen, G., Ren, C., Zou, Y., Qin, X., Shipeng, L.: Mechanism for material removal in ultrasonic vibration helical milling of Ti-6Al-4V alloy. Int. J. Mach. Tools Manuf 138, 1–13 (2019)10.1016/j.ijmachtools.2018.11.001 ↗
7. Devillez, A., Dudzinski, D.: Tool vibration detection with eddy current sensors in machining process and computation of stability lobes using fuzzy classifiers. Mech. Syst. Signal Process 21(1), 441456 (2007)10.1016/j.ymssp.2005.11.007 ↗
8. Ezugwu, E.O., Bonney, J., Yamane, Y.: An overview of the machinability of aeroengine alloys. J. Mater. Process Technol. 134, 233–253 (2003)10.1016/S0924-0136(02)01042-7 ↗
9. Gong, Y., Liang, C., Li, Q., Liu, M.: Wear experiment of carbide tool for milling nickel-based single crystal superalloy DD5. J. Northeast Univ. Nat. Sci. Ed. 39(09), 1283–1287 (2018)
10. Grossi, N., Scippa, A., Sallese, L., Campatelli, G.: On the generation of chatter marks in peripheral milling: a spectral interpretation. Int. J. Mach. Tools Manuf 133, 31–46 (2018)10.1016/j.ijmachtools.2018.05.008 ↗
11. Hadi, M., Kolahdouz, S. Surface integrity in high-speed milling of gamma titanium aluminide under MQL cutting conditions. In: 2014 5th Conference on Thermal Power Plants (CTPP), (2014)10.1109/CTPP.2014.7040696 ↗
12. Huiqun, Y.: Basis of Rotor Dynamics. Metallurgical Industry Press, China (2013)
13. Johnson, G.R., Cook, W.H.: Fracture character theistic of three metals subjected to various strains strain rates, temperatures and pressures[J]. Eng. Fract. Mech. 21(3), 31–48 (1985)10.1016/0013-7944(85)90052-9 ↗
14. Kaibo, L., Lian, Z., Fengshou, G., et al.: Model-based chatter stability prediction and detection for the turning of a flexible workpiece. Mech. Syst. Signal Process. 100, 814–826 (2018)10.1016/j.ymssp.2017.08.022 ↗
15. Klocke, F., Lung, D., Arft, M., Settineri, L.: On high-speed turning of a third-generation gamma titanium aluminide. Int. J. Adv. Manuf. Technol. 65, 155–163 (2012)10.1007/s00170-012-4157-5 ↗
16. Lalwani, D.I., Mehta, N.K., Jain, P.K.: Experimental investigations of cutting parameters influence on cutting forces and surface roughness in finish hard turning of MDN250 steel. J. Mater. Process Technol. 206, 167–179 (2008)10.1016/j.jmatprotec.2007.12.018 ↗
17. Li, J., Wang, C.: Effect of the feed rate on three-dimensional topography of Ti-6Al-4V based on dynamic mechanical model analysis in cutting process. Int. J. Adv. Manuf. Technol. 105(1–4), 1539–1547 (2019)10.1007/s00170-019-04373-y ↗
18. Li, J.-q, Xu, B.-c: Study on adiabatic shearing sensitivity of titanium alloy in the process of different cutting speeds. Int. J. Ady. Manuf. Technol. 93, 1859–1865 (2017)10.1007/s00170-017-0641-2 ↗
19. Liang, X., Liu, Z., Yao, G., Ren, X.: Investigation of surface topography and its deterioration resulting from tool wear evolution when dry turning of titanium alloy Ti-6Al-4V. Tribol. Int. 135, 130–142 (2019)10.1016/j.triboint.2019.02.049 ↗
20. Lindvall, R., Lenrick, F., Persson, H., M’Saoubi, R., Bushlya, V.: Performance and wear mechanisms of PCD and pcBN cutting tools during machining titanium alloy Ti6Al4V. Wear 454, 203329 (2020)10.1016/j.wear.2020.203329 ↗
21. Ooxley, P.L.B.: Mechanics of metal cutting. Int. J. Mach. Tool Des. Res. 1(1–2), 89–97 (1961)10.1016/0020-7357(61)90046-4 ↗
22. Pang, L.-j, Shang, X.-f: Principle of metal Cutting. National Defense Industry Press, China (2011)
23. Paris, H., Mayer, R.: Surface shape prediction in high speed milling. Int. J. Mach. Tools Manuf 44(15), 1567–1576 (2004)10.1016/j.ijmachtools.2004.06.005 ↗
24. Paris, H., Peigne, G., Mayer, R.: Surface shape prediction in high speed milling. Int. J. Mach. Tool Manuf. 44(15), 1567–1576 (2004)10.1016/j.ijmachtools.2004.06.005 ↗
25. Peng, C., Wang, L., Liao, T.W.: A new method for the prediction of chatter stability lobes based on dynamic cutting force simulation model and support vector machine. J Sound Vib 354(10), 118–131 (2015)10.1016/j.jsv.2015.06.011 ↗
26. Priarone, C., Rizzuti, S., Vergnano, G.: Effects of cutting angle, edge preparation, and nano-structured coating on milling performance of a gamma titanium aluminide. J. Mater. Process. Technol. 212(12), 2619–2628 (2012)10.1016/j.jmatprotec.2012.07.021 ↗
27. Quintana, G., Ciurana, J.: Chatter in machining processes: a review. Int. J. Mach. Tools Manuf. 51(5), 363–376 (2011)10.1016/j.ijmachtools.2011.01.001 ↗
28. Sadiq, T.O., Olawore S.A., Idris, J.: Energy consideration in machining titanium alloys with a low carbon manufacturing requirements: a critical review. Int. J. Eng. Res. Afr. (2018). https://doi.org/10.4028/www.scientific.net/JERA.35.8910.4028/www.scientific.net/JERA.35.89 ↗
29. Turkes, E., Orak, S., Neseli, S., Yaldiz, S.: Linear analysis of chatter vibration and stability for orthogonal cutting in turning. Int. J. Refract. Met. Hard Mater. 29(2), 163–169 (2011)10.1016/j.ijrmhm.2010.10.002 ↗
30. Wang, A., Jin, W., Xiaoyong, L.: Analysis on dynamics of a cutting tool with the thermal distortion in turning process. Nonlinear Dyn. 86(2), 1183–1191 (2016)10.1007/s11071-016-2956-1 ↗
31. Xiaofen, L.I.U., Wenhu, W.A.N.G., Jiang, R., Xiong, Y., Kunyang, L.I.N., Junchen, L.I., Chenwei, S.H.A.N.: Analytical model of cutting force in axial ultrasonic vibration-assisted milling in-situ TiB2/7050Al PRMMCs. Chin. J. Aeronaut. 34(4), 160–173 (2021)10.1016/j.cja.2020.08.009 ↗
32. Zhang, M., Zhang, D., Geng, D., Liu, J., Jiang, X.: Surface and sub-surface analysis of rotary ultrasonic elliptical end milling of Ti-6Al-4V. Mater. Des. 191, 108658 (2020)10.1016/j.matdes.2020.108658 ↗
33. Zhongqun, L.I., Qiang, L.I.U., Songmei, Y.U.A.N., Kaisheng, H.U.A.N.G.: Prediction of dynamic cutting force and regenerative chatter stability in inserted cutters milling. Chin. J. Mech. Eng. 26(3), 555–563 (2013)10.3901/CJME.2013.03.555 ↗