Novel setup for the investigation of tribological behavior of sheet metal surfaces
Source abstract
Abstract
In sheet metal forming processes tribological conditions have a significant influence on the quality of the produced part, the tool life time as well as the process stability. Due to the contact pressures in the workpiece-tool interface, mixed lubrication is predominant. Thus, the appearing real contact area has a major influence on the frictional conditions. During the forming process the real contact area increases, because of the flattening of topography asperities. For the investigation of flattening behaviour and the so connected changes in friction a new modular test rig for strip drawing tests has been developed. To gain additional information about the contact behaviour of texturized sheet metal surfaces during the tests, it is possible to alternate between two different measurement setups to investigate changes in the workpiece-tool interface in-situ. In the first setup, an ultrasonic inspection system is used while the second setup is based on optical techniques. In this paper the two measurement setups and the planned investigations are described.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Tribology and Lubrication Engineering · Adhesion, Friction, and Surface Interactions · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. Sørensen CG, Bech JI, Andreasen JL, Bay N, Engel U, Neudecker T (1999) A basic study of the influence of surface topography on mechanisms of liquid lubrication in metal forming. Annals of the CIRP 48(1):203–20810.1016/S0007-8506(07)63166-7 ↗
2. Shimizu I, Andreasen JL, Bech JI, Bay N (2001) Influence of workpiece surface topography on the mechanisms of liquid lubrication in strip drawing. ASME Journal of Tribology 123:290–29410.1115/1.1308017 ↗
3. Azushima A, Kudo H (1995) Direct obeservation of contact behaviour to interpret the pressure dependence of the coefficient of friction in sheet metal forming. Annals of the CIRP 1:209–21210.1016/S0007-8506(07)62309-9 ↗
4. Azushima A (2006) In situ 3D measurement of lubri- cation behavior at interface between tool and workpiece by direct fluorescence observation technique. Wear 260:243–24810.1016/j.wear.2005.01.053 ↗
5. Mizuno T, Okamoto M (1982) Effects of lubricant viscosity at pressure and sliding velocity on lubri- cating conditions in the compression-friction test on sheet metals. J Lubr Technology 104:53–5910.1115/1.3253164 ↗
6. Kudo H, Tsubouchi M, Takada H, Okamura K (1982) An investigation into plasto-hydrodynamic lubri*- cation with a cold sheet drawing test. Annals of the CIRP 31(1):175–18010.1016/S0007-8506(07)63292-2 ↗
7. Azushima, A.; Tsubouchi, M.; Kudo, H.: Direct observastion of lubricant behaviours under micro- PHL at the interface between workpiece and die. In: Proc. 3rd Int. Conf. Technol. Plasticity, Kyoto, 1990, 551-556
8. Azushima A, Uda M, Kudo H (1991) An interpretation of the speed dependence of the coefficient of friction in sheet metal forming. Annals of the CIRP 40(1):227–23010.1016/S0007-8506(07)61974-X ↗
9. Bech J, Bay N, Eriksen M (1999) Entrapment and escape of liquid lubricant in metal forming. Wear 232:134–13910.1016/S0043-1648(99)00136-2 ↗
10. Staeves J (1998) Beurteilung der Topographie von Blechen im Hinblick auf die Reibung bei der Umformung. Shaker Verlag, Aachen
11. Pfestdorf M (1997) Funktionale 3D-Oberflächenkenn- größen in der Umformtechnik. In: Geiger M, Feldmann K (eds) Fertigungstechnik– Erlangen, Bd. 72. Meisenbach, Bamberg
12. Geiger M, Engel U (1997) Pfestorf: new developments for the qualification of technical surfaces in forming processes. Annals of the CIRP 46(1):171–17410.1016/S0007-8506(07)60801-4 ↗
13. Blunt L, Jiang X (eds) (2003) Advanced Techniques for assessment surface topography: development of a basis for 3D surface texture standards “SURFSTAND”. Kogan Page, London
14. Wagner S (1997) 3D-Beschreibung der Oberflächen- strukturen von Feinblechen. In: Siegert K (ed) Beiträge zur Umformtechnik, Nr. 11. DGM, Oberursel
15. Sobis T, Engel U, Geiger M (1992) A theoretical study of wear simulation in metal forming processes. J Mater Process Technol 34:233–24010.1016/0924-0136(92)90112-6 ↗
16. Geiger M, Engel U, Pfestorf M (1997) New developments for the qualification of technical surfaces in forming processes. Annals of the CIRP 46(1):171–17410.1016/S0007-8506(07)60801-4 ↗
17. Geiger M, Engel U, Vollertsen F (1992) In situ ultrasonic measurement of the real contact area in bulk metal forming. Annals of the CIRP 41(1):255–25810.1016/S0007-8506(07)61198-6 ↗
18. Stancu-Niederkorn S, Engel U, Geiger M (1994) Ultrasonic investigation of friction mechanism in metal forming. J Mater Process Technol 45(1-4):623–61810.1016/0924-0136(94)90407-3 ↗