Demands on process and process energy sources for the electro-erosive and electrochemical micro machining
Source abstract
Abstract
This article will demonstrate which demands are required from process energy sources (PES), if the non-conventional machining procedures EDM (Electrical Discharge Machining) and ECM (Electrochemical Machining) are efficiently used for the micro machining. Due to the very low working gap, the process conditions are considerably changed compared to the previous machining conditions. The well known PES-concepts can no longer be treated without paying attention to the supply parameter (feeder parameters) and the gap parameter. A very efficient machining procedure is the μ-PECM, which uses the charge reversal of double layers.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Machining and Optimization Techniques · Advanced machining processes and optimization · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (10)
Show source-provided references
1. W. Rehbein, H.-P. Schulze, M. Storr, G. Wollenberg, The Influence of additives in dielectric fluids for Electrical Discharge Machining.15 th Intern. Symposium on Electromachining (ISBN 978–0–9794977), April 23–27, 2007, Pittsburgh, USA, pp. 99–104.
2. V. Kirchner, Elektrochemische Mikrostrukturierung mit ultrakurzen Spannungsimpulsen, Diss. FU Berlin, 2001.
3. M. Läuter, H.-P. Schulze, G. Wollenberg, Modern process energy sources for electrical discharge machining (EDM). 18 th Intern. Conf. on Computer-aided Production Engineering (CAPE), March, 18–19, 2003, Edinburgh, UK, Prof. Engineering Publishing Limited London and Bury St. Edmunds, UK (ISBN 1 86058 404 7), pp. 339–348.
4. H.-P. Schulze, M. Läuter, G. Wollenberg, M. Zybura-Skrabalak, A. De Silva, Process energy sources for the electrochemical machining process and hybrid machining with ECM. 3 rd Intern. Conf. on Machining and Measurement of Sculptured Surface, (MMSS), September, 24–26, 2003, Krakow, Poland, pp. 367–378.
5. H.-P. Schulze, G. Wollenberg, S. Matzen, K. Mecke, Origins of gas bubbles in a small work gap during the Micro-EDM. 5 th Intern. Symposium on Electromachining (ISBN 978–0–9794977), April 23–27, 2007, Pittsburgh, USA, pp. 211–216.
6. W. Rehbein, H.-P. Schulze, Change of ignition conditions at the spark erosion process by adding molecules with defined chemical structures to a dielectric fluid. 2005 IEEE International Conference on Dielectric Liquids (ICDL), June 26 – July 1, 2005, Coimbra, Portugal, pp. 127–130.
7. R. Schuster, V. Kirchner, P. Allonque, G. Ertl, Electrochemical Micromachining. Science, 289 (2000).10.1126/science.289.5476.98 ↗
8. H.-P. Schulze, St. Burkert, G. Wollenberg, M. Leone, Improvement of the hole and micro hole sinking using hybrid machining process. 20 th Intern. Conference on Computer-aided Production Engineering (CAPE), June, 6–8, 2007, Glasgow, UK, Prof. Engineering Publishing Limited London and Bury St. Edmunds, UK (ISBN 13 978–1–905866–14–4), pp. 162–166.
9. H.-P. Schulze, M. Läuter, W. Rehbein, K. Mecke, G. Wollenberg, Channel spreading during the spark discharge for selected conditions and working fluids. 2003 IEEE Annual Report Conference on Electrical Insulation and Dielectric Phenomena, October, 19–22, 2003, Albuquerque, USA, pp. 297–300.
10. T. Gmelin, H. Kück, Ultra precise sink erosion of steel using Electrochemical Micromilling (ECF/mPECM) with ultrashort voltage pulses. Intern. Symposium on ElectroChemical Machining Technology (INSECT) 2007,October 25–26, 2007, Chemnitz, Germany, pp. 23–28.