Hydraulic bulge testing to compare formability of continuous and stretch broken carbon fiber reinforced polymer composites
Source abstract
Abstract
This version of the article has been accepted for publication, after peer review (when applicable) and is subject to Springer Nature's AM terms of use, but is not the Version of Record and does not reflect post-acceptance improvements, or any corrections. The Version of Record is available online at: http://dx.doi.org/10.1007/s12289-023-01743-6. Deposited by shareyourpaper.org and openaccessbutton.org. We've taken reasonable steps to ensure this content doesn't violate copyright. However, if you think it does you can request a takedown by emailing help@openaccessbutton.org.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical Behavior of Composites · Fiber-reinforced polymer composites · Additive Manufacturing and 3D Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. Hull D, Clyne TW (1981) B. An Introduction to Composite Materials, Cambridge. 1st Edition Solid State Sci Ser 9–38
2. Ning F, Cong W, Hu Z, Huang K (2017) Additive manufacturing of thermoplastic matrix composites using fused deposition modeling: A comparison of two reinforcements. J Compos Mater 51(27):3733–374210.1177/0021998317692659 ↗
3. Lee K, Lee SW, Ng SJ (2008) Micromechanical modeling of stretch broken carbon fiber materials. J Compos Mater 42(11):1063–107310.1177/0021998308090449 ↗
4. Li Y, Chen Z, Xu H, Dahl J, Zeng D, Mirdamadi M, Su X (2017) Modeling and simulation of compression molding process for sheet molding compound (SMC) of chopped carbon fiber composites. SAE Int J Mater Manuf 10(2):130–13710.4271/2017-01-0228 ↗
5. Eyckens DJ, Arnold CL, Simon Ž, Gengenbach TR, Pinson J, Wickramasingha YA, Henderson LC (2021) Covalent sizing surface modification as a route to improved interfacial adhesion in carbon fibre-epoxy composites. Compos A Appl Sci Manuf 140:10614710.1016/j.compositesa.2020.106147 ↗
6. Den Uijl NJ, Carless LJ (2012) Advanced metal-forming technologies for automotive applications. In: Advanced materials in automotive engineering (pp. 28–56). Woodhead Publishing10.1533/9780857095466.28 ↗
7. Schuster J, Kazmi SMR, Lutz J (2015) Manufacturing and Testing of Curved Fibre composites Using Vacuum Assisted Resin Transfer Moulding (VARTM). In: 20th International Conference on Composite Materials (ICCM-20), Copenhagen, pp 19–24
8. Campbell FC (2010) Structural Composite Materials. ASM International, Ohio10.31399/asm.tb.scm.9781627083140 ↗
9. Medina C, Canales C, Arango C, Flores P (2014) The influence of carbon fabric weave on the in-plane shear mechanical performance of epoxy fiber-reinforced laminates. J Compos Mater 48(23):2871–287810.1177/0021998313503026 ↗
10. Wang F (2017) Carbon fibers and their thermal transporting properties. In: Thermal transport in carbon-based nanomaterials. Elsevier, pp 135–18410.1016/B978-0-32-346240-2.00006-6 ↗
11. Rahmani H, Najafi SHM, Saffarzadeh-Matin S, Ashori A (2014) Mechanical properties of carbon fiber/epoxy composites: Effects of number of plies, fiber contents, and angle-ply layers. Polym Eng Sci 54(11):2676–268210.1002/pen.23820 ↗
12. Rahmani H, Najafi SHM, Ashori A (2014) Mechanical performance of epoxy/carbon fiber laminated composites. J Reinf Plast Compos 33(8):733–74010.1177/0731684413518255 ↗
13. Janicki JC, Egloff MC, Amendola R, Ryan CA, Bajwa DS, Dynkin A, Cairns DS (2021) Formability Characterization of Fiber Reinforced Polymer Composites Using a Novel Test Method. J Test Eval 50(2). https://doi.org/10.1520/JTE2021025010.1520/JTE20210250 ↗
14. Jacobsen G, Schimpf W (2008) Process Development and Characterization of Stretch Broken Carbon Fiber Materials. Hexcel Corp., Utah. www.hexcel.com/innovation/Documents/Process%20Development%20and%20Characterization%20of%20Stretch%20Broken%20Carbon%20Fiber%20Materials.pdf. Accessed 2 Apr 202
15. Şükür EF, Türköz M, Dilmeç M, Halkacı HS, Halkacı M (2016) Comparison of flow curves of AA 5457-O sheet material determined by hydraulic bulge and tensile tests at warm forming temperatures. J Test Eval 44(2):952–96610.1520/JTE20150346 ↗
16. Srbislav A, Milentije S, Dragan A, Vukić L (2009) Variation of Normal Anisotropy Ratio" r" during Plastic Forming. J Mech Eng 55(6):392–399
17. Eyckens D, Arnold C, Simon Ž, Gengenbach T, Pinson J, Wickramasingha Y, Henderson L (2021) Covalent sizing surface modification as a route to improved interfacial adhesion in carbon fibre-epoxy composites. Composites 140:106147. https://doi.org/10.1016/j.compositesa.2020.10614710.1016/j.compositesa.2020.106147 ↗
18. Jacobsen G (2010) Mechanical characterization of stretch broken carbon fiber materials IM7 fiber in 8552 resin, SAMPE 10 Spring Symposium Technical Conference Proceedings, pp 17–20
19. Pavan kumar J, Uday kumar R, Ramakrishna B, Ramu B, Baba Saheb K (2018) Formability of sheet metals–A review. International Conference on Advancements in Aeromechanical Materials for Manufacturing; Telangana (India); July 13-14, https://doi.org/10.1088/1757-899X/455/1/01208110.1088/1757-899X/455/1/012081 ↗
20. Bruschi S, Altan T, Banabic D, Bariani PF, Brosius A, Cao J, Tekkaya AE (2014) Testing and modelling of material behaviour and formability in sheet metal forming. CIRP Ann 63(2):727–74910.1016/j.cirp.2014.05.005 ↗
21. ASTM International (2015) E643–15 Standard Test Method for Ball Punch Deformation of Metallic Sheet Material. ASTM International, West Conshohocken, PA
22. ASTM International (2015) E2712–15 Standard Test Methods for Bulge-Forming Superplastic Metallic Sheet. ASTM International, West Conshohocken, PA
23. Miranda SS, Santos AD, Amaral RL, Malheiro LT (2019) Characterization and Formability Analysis of a Composite Sandwich Metal-Polymer Material. In: Materials Design and Applications II. Springer, pp 487–508. https://doi.org/10.1007/978-3-030-02257-0_3310.1007/978-3-030-02257-0_33 ↗
24. Hueber C, Fischer G, Schwingshandl N, Schledjewski R (2019) Production planning optimisation for composite aerospace manufacturing. Int J Prod Res 57(18):5857–587310.1080/00207543.2018.1554918 ↗
25. Hextow IM7 carbon fiber datasheet, Hexcel Corp., Connecticut (2020). www.hexcel.com/user_area/content_media/raw/IM7_HexTow_DataSheet.pdf. Accessed 10 Apr 2022
26. Huntsman RDM 2019-053 Data Sheet (The Woodlands, TX: Huntsman, 2020).
27. Sur F, Blaysat B, Grédiac M (2018) Rendering deformed speckle images with a Boolean model. J Mathe Imaging Vis 60(5):634–65010.1007/s10851-017-0779-4 ↗
28. ASTM International (2015) E2218–15 Standard Test Method for Determining Forming Limit Curves. ASTM International, West Conshohocken, PA
29. Weisstein Eric W (n.d.) "Oblate Spheroid." From MathWorld--A Wolfram Web Resource. https://mathworld.wolfram.com/OblateSpheroid.html. Accessed 3 Mar 2022