Effect of slide motion on springback in 2-D draw bending for AHSS
Source abstract
Abstract
The springback behavior of two advanced high strength steel (AHSS) grades, DP 780 and DP 980, after different forming conditions, was investigated. 2-D draw bending experiments were performed using a direct-drive digital servo-press in three operation modes, conventional (V-mode), relaxation mode (Stepwise and U-mode) and the attach-detach (A-D mode). Numerical simulations were conducted to in an attempt to reproduce the results and to perform parametric studies. The material behavior was captured using the homogeneous anisotropic hardening (HAH) distortional plasticity approach together with the chord elastic modulus model. In addition, the stress relaxation effects were implemented in the code by using a creep law in order to study the influence of a stepwise slide motion mode as well as holding at the bottom dead center. Both experimental and finite element (FE) simulation results demonstrate that detachment of tools from the work-piece was effective to reduce the springback while the effect of stress relaxation was insignificant. The numerical analysis was validated and successfully explained the importance of a forming path change on the final stress state. Based on the result of this study, a new method to reduce springback was introduced.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Forming Simulation Techniques · Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Wagoner RH, Lim H, Lee M-G (2013) Advanced Issues in springback. Int J Plast 45:3–2010.1016/j.ijplas.2012.08.006 ↗
2. Banabic D (2010) Sheet Metal Forming Processes: Constitutive Modelling and Numerical Simulation. Springer, Berlin10.1007/978-3-540-88113-1 ↗
3. Lingbeek RA, Gan W, Wagoner RH, Meinders T, Weinders J (2008) Theoretical verification of the displacement adjustment and springforward algorithms for springback compensation. Int J Mater Form 1(3):159–16810.1007/s12289-008-0369-5 ↗
4. Osakada K, Mori K, Altan T, Groche P (2011) Mechanical servo press technology for metal forming. CIRP Annals-Manuf Technol 60:651–67210.1016/j.cirp.2011.05.007 ↗
5. Murata C, Yabe J, Endou J, Hasegawa K (2013) Direct Drive Digital Servo Press with High Parallel Control. AIP Conf Proc 1567:1016–101910.1063/1.4850143 ↗
6. Mori K, Akita K, Abe Y (2007) Springback behaviour in bending of ultra-high strength steel sheets using CNC servo press. Int J Mach Tool Manuf 47:321–32510.1016/j.ijmachtools.2006.03.013 ↗
7. Suganuma T (2008) Application of servo press to sheet metal forming. J Jpn Soc Technol Plast 49:118–12210.9773/sosei.49.118 ↗
8. Majidi O, Bong H, Barlat F, Lee M-G, Kim C (2012) Effect of slide velocity on springback in U-draw bending of AHSS sheets with digital servo-press. Steel res Int 83:347–350
9. Chaboche JL (1986) Time-independent constitutive theories for cyclic plasticity. Int J Plast 2:149–18810.1016/0749-6419(86)90010-0 ↗
10. Chung K, Lee M-G, Kim D, Kim C, Wenner ML, Barlat F (2005) Spring-back evaluation of automotive sheets based on isotropic–kinematic hardening laws and non-quadratic anisotropic yield functions – Part I: theory and formulation. Int J Plast 21:861–882
11. Yoshida F, Uemori T, Fujiwara K (2002) Elastic–plastic behavior of steel sheets under in-plane cyclic tension–compression at large strain. Int J Plast 18:633–65910.1016/S0749-6419(01)00049-3 ↗
12. Zang S-L, Lee M-G, Kim J-H (2013) Evaluating the significance of hardening behavior and unloading modulus under strain reversal in sheet springback prediction. Int J Mech Sci 77:194–20410.1016/j.ijmecsci.2013.09.033 ↗
13. Korkolis DN, Kuwabara T (2013) Biaxial unloading and springback behavior of dual-phase DP590 steel using cruciform specimens. AIP Conf Proc 1567:700–70410.1063/1.4850068 ↗
14. Cleveland RM, Ghosh AK (2002) Inelastic effects on springback in metals. Int J Plast 18:769–78510.1016/S0749-6419(01)00054-7 ↗
15. Yu HY (2009) Variation of elastic modulus during plastic deformation and its influence on springback. J Mater Des 30:846–85010.1016/j.matdes.2008.05.064 ↗
16. Eggertsen PA, Mattiasson K (2010) On the Modeling of the Unloading Modulus for Metal Sheets. Int J Mater Form 3(1):127–13010.1007/s12289-010-0723-2 ↗
17. Eggertsen PA, Mattiasson K (2011) On the identification of kinematic hardening material parameters for accurate springback predictions. Int J Mater Form 4:103–12010.1007/s12289-010-1014-7 ↗
18. Lee J-W, Lee J-Y, Barlat F, Wagoner RH, Chung K, Lee M-G (2013) Extension of quasi-plastic–elastic approach to incorporate complex plastic flow behavior– application to springback of advanced high-strength steels. Int J Plast 45:140–15910.1016/j.ijplas.2013.01.011 ↗
19. Chongthairungruang B, Uthaisangsuk V, Suranuntchai S, Jirathearanat S (2013) Springback prediction in sheet metal forming of high strength steels. J Mater Des 50:253–26610.1016/j.matdes.2013.02.060 ↗
20. Barlat F, Gracio JJ, Lee M-G, Rauch EF, Vincze G (2011) An alternative to kinematic hardening in classical plasticity. Int J Plast 27:1309–132710.1016/j.ijplas.2011.03.003 ↗
21. Barlat F, Ha J, Grácio JJ, Lee M-G, Rauch EF, Vincze G (2013) Extension of homogeneous anisotropic hardening model to cross loading with latent effects. Int J Plast 46:130–14210.1016/j.ijplas.2012.07.002 ↗
22. Lee J-Y, Lee J-W, Lee M-G, Barlat F (2012) An application of homogeneous anisotropic hardening to springback prediction in pre-strained U-draw/bending. Int J Solid Struct 49:3562–357210.1016/j.ijsolstr.2012.03.042 ↗
23. Tamai Y, Yamasaki Y, Yoshitake A, Imura T (2010) Improvement of formability in stamping of steel sheets by motion control of servo press. Steel Res Int 81(9):686–689
24. ABAQUS User’s Manual Version 6.10 (2010), Hibbit, Karlsson & Sorensen Inc, Rhode Island
25. Chung K, Kuwabara T, Verma RK, Park T (2011) Numisheet 2011 Benchmark 4: Pre-strain effect on spring-back of 2D draw bending. In: Huh H et al (eds) Proceedings 8th NUMISHEET conference. Seoul, Korea, pp 171–175
26. Choi J (2013) Simple shear flow behavior for Advanced High Strength Steel (AHSS) sheets, in Graduate Institute of Ferrous Technology. Pohang University of, Science and Technology (POSTECH), p 65
27. Norton FH (1929) Creep of steel at high temperatures. McGraw-Hill, New York
28. Bailey RW (1930) Creep of steel under simple and compound stress. Engineering 121:129–265