Deformation behaviour of bulk materials during repetitive upsetting-extrusion (RUE)
Source abstract
Abstract
Repetitive upsetting-extrusion (RUE) that was originally invented to process powder materials for bulk mechanical alloying is currently being used to process bulk materials. Bulk materials are subjected to severe plastic deformation using the same die design that was used to process powder materials. As the deformation behaviour of powder and bulk materials are quite different, it has to be evaluated whether a single die design is suitable to process both these materials. Further, information on the deformation behaviour and strain homogeneity that can be achieved by subjecting bulk materials to RUE process are also currently not available. To address these issues, both numerical analysis and actual experiments on commercial pure copper has been carried out. The results obtained are presented and discussed here
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Powder Metallurgy Techniques and Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (15)
Show source-provided references
1. Valiev RZ, Islamgaliev IV, Alexandrov IV (2000) Bulk nanostructured materials from severe plastic deformation. Prog Mater Sci 45:103–18910.1016/S0079-6425(99)00007-9 ↗
2. Azushima A, Koop R, Korhonen A, Yang DY, Micari F, Lahoti GD, Groche P, Yanagimoto J, Tsuji N, Rosochowski R, Yanagia A (2008) Severe plastic deformation processes for metals. CIRP Ann Manuf Technol 57:716–73510.1016/j.cirp.2008.09.005 ↗
3. Alexander DJ (2007) New methods for severe plastic deformation processing. J Mater Eng Perform 16-3:360–37410.1007/s11665-007-9054-y ↗
4. Valiev RZ, Langdon TG (2006) Principles of equal channel angular pressing as processing tool for grain refinement. Prog Mater Sci 51:881–98110.1016/j.pmatsci.2006.02.003 ↗
5. Lowe TC, Valiev RZ (2000) Producing nanoscale microstructures through severe plastic deformation. J Metals. April: 27–2810.1007/s11837-000-0127-8 ↗
6. Aizawa T, Tokimutu K (1999) Bulk mechanical alloying for productive processing of functional alloys. Mat Sci Forum 312–314:13–2210.4028/www.scientific.net/MSF.312-314.13 ↗
7. Lianxi H, Yuping L, Erde W, Yang Y (2006) Ultrafine grained structure and mechanical properties of a LY12 Al alloy prepared by repeated upsetting-extrusion. Mat Sci Eng A 422:327–33210.1016/j.msea.2006.02.014 ↗
8. Kalpakjian S, Schmid SR (2003) Manufacturing processes for engineering materials, 4th ed. India: Pearson Education (Singapore) Pte, Ltd.
9. Dieter GE (1998) Chapter.18 extrusion in mechanical metallurgy. Mcgraw-Hill, New York, pp 616–634
10. Kraft FF, Gunasekera JS (2004) Conventional hot extrusion. In: Semiatin SL (ed) ASM handbook vol14 a metal working-bulk forming. ASM International Material Park, Ohio, pp 421–434
11. Gupta OP (1999) Section 2.4 Axi-symmetric analysis. In: Finite and boundary element methods in Eng. Reprint 2000. Oxford & IBH Publishing Co. Pvt. Ltd, India, pp 55–90
12. MSC MARC 2007R1, Marc volume A—theory and user information. MSC corporation, Santa Ana, CA, USA
13. Anjali MC, Katti K (2009) Repetitive upsetting and extrusion of commercial pure copper, Dept. of Met and Mater Technol., Mahatma Gandhi Institute of Technol, B.Tech Pre-project Report
14. Balasundar I, Raghu T (2010) Investigations on the extrusion defect - Axial hole or funnel. J Mater Design. doi: 10.016/j.matdes.2010.01.02710.1016/j.matdes.2010.01.027 ↗
15. Patil Basavaraj V, Uday Chakkingal TS, Kumar P (2009) Study of channel angle influence on material flow and strain inhomogeneity in equal channel angular pressing using 3D finite element simulation. J Mater Process Technol 209:89–9510.1016/j.jmatprotec.2008.01.031 ↗