Modeling and experimental validation of the surface residual stresses induced by hard machining of AISI H13 tool steel
Source abstract
Abstract
Residual stresses induced by orthogonal cutting of AISI H13 tool steel were modeled and simulated using Finite Element (FE) method. A two-dimensional model using elastic-plastic material behavior, shear friction model and a physical chip separation criterion for chip formation were developed. To validate this model the predicted surface residual stresses were compared with those experimentally obtained using X-ray diffraction technique. Finally, the proposed FE model was applied to investigate the influence of flank tool wear and cutting regime parameters on surface residual stresses distribution in the machined surface of AISI H13 tool steel.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced machining processes and optimization · Advanced Surface Polishing Techniques · Advanced Machining and Optimization Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (13)
Show source-provided references
1. Tönshoff, H.K., Arendt C., Ben Amor R., Cutting of Hardened Steel, Annals of the CIRP, 49(2):547–566, 2000.10.1016/S0007-8506(07)63455-6 ↗
2. Byrne, G., Dornfeld, D., Denkena, B., Advancing Cutting Technology, Annals of the CIRP, 52(2):483–507, 2003.10.1016/S0007-8506(07)60200-5 ↗
3. Thiele, J.D. and S.N. Melkote, Effect of Tool Edge Geometry on Workpiece Subsurface Deformation and Through Thickness Residual Stresses for Hard Turning of AISI 52100 Steel. SME, J. Manuf Proc., 2(4):1–7, 2000.
4. Thiele, J.D., et al., Effect of Cutting-Edge Geometry and Workpiece Hardness on Surface Residual Stresses in Finish Hard Turning of AISI 52100 Steel. J. of Manuf. Sci. Eng., 122:642–649, 2000.10.1115/1.1286369 ↗
5. Strenkowski, J.T. Carroll, A finite element model of orthogonal metal cutting, J. Eng. Ind., 107:349–354, 1985.10.1115/1.3186008 ↗
6. Chen, L., et al., Effects of Edge Preparation and Feed when Hard Turning a Hot Work Die Steel with Polycrystalline Cubic Boron Nitride Tools. Annals of the CIRP, 55(1):89–92, 2006.10.1016/S0007-8506(07)60373-4 ↗
7. Noyan, I.C. and J.B. Cohen, Residual Stress - Measurement by Diffraction and Interpretation. Society for Experimental Mechanics ed. 1987, New York: Springer-Verlag.
8. J.T. Carroll, J.S. Strenkowsky, Finite element models of orthogonal cutting with application to single point diamond turning, Int. J. Mech. Sci., 30:899–920, 1988.10.1016/0020-7403(88)90073-2 ↗
9. T. Tyan, W.H. Yang, Analysis of orthogonal metal cutting processes. Int. J. Numer. Meth Eng., 34:365–389, 1992.10.1002/nme.1620340122 ↗
10. J.M. Huang, J.T. Black, An evaluation of chip separation criteria for the FEM simulation of machining, J. Manuf. Sci. Eng., 118:545–554, 1996.10.1115/1.2831066 ↗
11. A.J. Shih, Finite element analysis of orthogonal metal cutting mechanics, Int. J. Mach. Tools Manuf., 36:225–273, 1996.
12. Umbrello, D., et al., Hardness-Based Flow Stress for Numerical Simulation of Hard Machining AISI H13 Tool Steel. J. Mater. Proc. Technol., 199(1–3): 64–73, 2008.10.1016/j.jmatprotec.2007.08.018 ↗
13. Shatla, M., C. Kerk, and T. Altan, Process modeling in machining. Part I: determination of flow stress data. Int. J. Mach. Tools Manuf., 41: 1511–1534, 2001.10.1016/S0890-6955(01)00016-5 ↗