Incremental cyclic fracture behaviour of 20MnMoNi55 steel at room temperature
Source abstract
Abstract
Fracture behavior of low alloy steel 20MnMoNi55 has been evaluated under cyclic loading condition. Effect of unloading extent and degree of cycling on fracture resistance has been evaluated by varying load ratio \((R)\) and incremental plastic displacement \((\varDelta V)\). It is observed that the initiation fracture toughness and tearing modulus decreased significantly with more negative \(R\) ratio and decrease in incremental plastic displacement. Examination of interrupted cyclic fracture test specimens revealed considerable crack tip re-sharpening and suppression of void growth and this is thought to be the reason for the reduction in fracture resistance under cyclic loading.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fatigue and fracture mechanics · High Temperature Alloys and Creep · Material Properties and Failure Mechanisms
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Dowling NE (1976) Geometry effects and the J-integral approach to elastic–plastic fatigue crack growth. In: ASTM STP 601, Philadelphia PA, ASTM, 19–3210.1520/STP28635S ↗
2. Dowling NE, Begley JA (1976) Fatigue crack growth during gross plasticity and the J-integral. In: ASTM STP 590, Philadelphia PA, ASTM, 82–10310.1520/STP33940S ↗
3. E647 (2011) Standard test method for measurement of fatigue crack growth rates. In: Annual book of ASTM standards
4. E1820 (2011) Standard test method for measurement of fracture toughness. In: Annual book of ASTM standards
5. El Haddad MH, Mukherjee B (1983) Elastic–plastic fracture mechanics analysis of fatigue crack growth. In: ASTM STP 803, Philadelphia, PA, ASTM, II 689–II 707
6. Joyce JA (1988) Development of a criterion for the effect on the JR curve of elastic unloadings. Fracture mechanics: eighteenth symposium ASTM STP 945:647–662
7. Joyce JA, Sutton GE (1985) An automated method of computer controlled low cycle fatigue crack growth testing using the elastic–plastic parameter cyclic J. In: ASTM STP 877, 227–247
8. Joyce JA, Hackett EM, Roe C (1994) Effect of cyclic loading on the deformation and elastic–plastic fracture behavior of a cast stainless steel. In: ASTM STP 1207, ASTM, 722–74110.1520/STP13735S ↗
9. Kaiser S (1983) On the relation between stable crack growth and fatigue. Fatigue Fract Eng Mater Struct 6:33–4910.1111/j.1460-2695.1983.tb01137.x ↗
10. Kobayashi H, Kusumoto T, Nakazawa H (1992) The cyclic J–R curve and upper limit characteristic of fatigue-crack growth in 2.5Cr-1Mo steel. Int J Press Vessel Pip 52:337–35610.1016/0308-0161(92)90090-3 ↗
11. Landes JD, Liaw PK (1987) Effect of cyclic loading on fracture toughness of a modified 4340 steel. In: Effect of load and thermal histories on mechanical behaviour of materials, Denver, Colorado, 241–246
12. Landes JD, McCabe DE (1983) Load history effect on the J–R curve. In: ASTM STP 803, ASTM, II-723–II 738
13. Marschall CW, Wilkowski GM (1991) Effect of cyclic loading on ductile fracture resistance. J Press Vessel Technol 113:358–36710.1115/1.2928767 ↗
14. McClung RC, Hudak SJ Jr (1994) Surface crack growth in Incone1718 during large unload–reload cycles. In: ASTM STP 1207, ASTM, 706–721
15. Mogami K, Hayashi K, Ando K, Ogura N (1990) Elastic plastic fatigue crack growth and tearing instability behaviour under cyclic loads. Int J Press Vessel Pip 44:85–9710.1016/0308-0161(90)90008-6 ↗
16. Narasaiah N, Sivaprasad S, Tarafder S (2010) Effect of crack depth on fracture toughness of 20MnMoNi55 pressure vessel steel. Mater Sci Eng A527:2408–241110.1016/j.msea.2009.12.011 ↗
17. NUREG CR 1061 (1984) Report of the US nuclear regulatory piping review committee. Evaluation of potential for pipe breaks, vol 3, US Nuclear Regulatory Commission, Washington, DC
18. Paris PC, Tada H, Ernest H, Zahoor A (1979) Initial experimental investigation of tearing instability theory. In: ASTM STP 668, ASTM, 251–26510.1520/STP35834S ↗
19. Roy H, Sivaprasad S, Tarafder S, Ray KK (2009) Monotonic vis-à-vis cyclic fracture behaviour of AISI 304LN stainless steel. Eng Fract Mech 76:1822–183210.1016/j.engfracmech.2009.04.001 ↗
20. Rudland DL, Brust F, Wilkowski GM (1992) The effect of cyclic and dynamic loading on the fracture resistance of nuclear piping steel. In: Report NUREG/CR-6440, Oct 1992–April 1996
21. Scot P (2003) Development of the technical basis for a new regulatory guide for leak before break applications. In: Transactions of the 17th international conference, SmiRT17, Prague, Czech Republic, Aug 17–22, Paper # G10–15
22. Seok C-S, Yoon B-G, Murthy KL (1999) A study on the decrease phenomenon of fracture resistance value under reversed cyclic loading. In: Transaction of the 15th international conference on structural mechanics in reactor technology (SmiRT-15) Seoul Korea, Aug 15–20, 1999, V487–V494
23. Seok C-S, Murthy LK (2000) A study on the decrease of fracture resistance curve under reversed cyclic loading. Int J Press Vessel Pip 77:303–31110.1016/S0308-0161(00)00018-1 ↗
24. Singh PK, Ranganath VR, Tarafder S, Prasad P, Bhasin V, Vaze KK (2003) Effect of cyclic loading on elastic–plastic fracture resistance of PHT system piping material of PHWR. Int J Press Vessel Pip 80:745–75210.1016/S0308-0161(03)00133-9 ↗
25. Sutton GE, Vassilaros MG (1986) Influence of partial unloading range on the J–R curve of ASTM A106 and 3-Ni steels. In: ASTM STP 905, ASTM, 364–378
26. Tanaka K, Hoshide T, Nakata M (1983) Elastic–plastic crack propagation under high cyclic stresses. In: ASTM STP 803, II-708– II72210.1520/STP36794S ↗
27. Tarafder S, Ranganath VR, Sivaprasad S, Johri P (2003) Ductile fracture behaviour of primary heat transport piping material for nuclear reactors. Sãdhanã 28:167–86
28. Tarafder S, Ranganath VR, Johri P (2004) Fracture resistance to PHT piping material to simulated seismic loading. Met Mater Process 16:295–306