Structural integrity of shot peened Ti6Al4V specimens under fretting fatigue
Source abstract
Abstract
Abstract In the present paper, an experimental campaign performed on shot peened Ti6Al4V specimens under fretting fatigue, available in the literature, is simulated by using the Carpinteri et al. criterion. The experiments examined were carried out using a standard configuration, that is, a cylinder against a flat specimen. The fretting loading is a combination of low-cycle fatigue and high-cycle fatigue, and the corresponding stress field is determined by a FE analysis. A theoretical law is applied to describe the relaxed residual stress produced by shot peening treatment and fatigue loading.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Mechanical stress and fatigue analysis · Fatigue and fracture mechanics · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. Araújo JA, Nowell D (2009) Mixed high low fretting fatigue of Ti6Al4V: tests and modelling. Tribol Int 42:1276–128510.1016/j.triboint.2009.04.024 ↗
2. Araújo JA, Carpinteri A, Ronchei C, Spagnoli A, Vantadori S (2014) An alternative definition of the shear stress amplitude based on the maximum rectangular hull method and application to the C-S (Carpinteri-Spagnoli) criterion. Fract Eng Mater Struct 37:764–77110.1111/ffe.12180 ↗
3. Araújo JA, Almeida GMJ, Ferreira JLA, da Silva CRM, Castro FC (2017) Early cracking orientation under high stress gradient: the fretting. Int J Fatigue 100:302–31110.1016/j.ijfatigue.2016.12.013 ↗
4. Boller C, Seeger T (1987) Material data for cyclic loading. PART D: aluminium and titanium alloys. Mater. Sci. Monogr., Elsevier Science Publisher B.V. Amsterdam, The Netherlands
5. Calcaterra JR, Golden PJ (2006) A fracture mechanics life prediction methodology applied to dovetail fretting. Tribol Int 39:1172–8010.1016/j.triboint.2006.02.006 ↗
6. Carpinteri A, Vantadori S, Zanichelli A (2019) Lifetime estimation of mechanical assemblies under constant amplitude fretting fatigue loading. Fatigue Fract Eng Mater Struct 42:1927–193610.1111/ffe.13043 ↗
7. Chan KS, Lee Y-D, Davidson DL (2001a) A fracture mechanics approach to high cycle fretting fatigue based on the worst case fret concept. I. Model development. Int J Fract 112:299–330
8. Chan KS, Davidson DL, Owen TE, Lee Y-D, Hudak SJ Jr (2001b) A fracture mechanics approach to high cycle fretting fatigue based on the worst case fret concept. II. Experimental evaluation. Int J Fract 112:331–35310.1023/A:1013519825958 ↗
9. Farrahi GH, Lebrun JL, Couratin D (1995) Effect of shot peening on residual stress and fatigue life of a spring steel. Fatigue Fract Eng Mater Struct 18:211–22010.1111/j.1460-2695.1995.tb00156.x ↗
10. Fouvry S, Kapsa Ph, Vincent L (1995) Analysis of sliding behaviour for fretting loadings: determination of transition criteria. Wear 185:35–4610.1016/0043-1648(94)06582-9 ↗
11. Gao YK, Yao M, Li JK (2002) An analysis of residual stress fields caused by shot peening. Metall Mater Trans A 33A:177510.1007/s11661-002-0186-2 ↗
12. Hamada S, Zhang K, Koyama M, Ueda M, Noguchi H (2020) Fatigue crack propagation modes: plastic deformation mode and damage accumulation mode. Int J Fract 222:111–12210.1007/s10704-020-00433-7 ↗
13. Higounenc O (2005) Correlation of shot peening parameters to surface characteristic. In: Proceedings of the 9th International Conference on Shot Peening, Paris, p 2005047
14. Hills DA, Nowell D (1994) Mechanics of fretting fatigue. Kluwer Academic Publishers, Dordrecht10.1007/978-94-015-8281-0 ↗
15. International ASM, Friction, lubrication, and wear technology, vol 18, Totten G.E. (eds) (2017) Materials Park. Ohio, USA
16. Kapsa P (2011) Environmental effects in fretting. In: Landolt D, Mischler S (eds) Tribocorrosion of passive metals and coatings, 1st edn. Woodhead Publishing, Cambridge, pp 100–11710.1533/9780857093738.1.100 ↗
17. Kirk D (2014) Estimate compressed layer depth by using Almen peening intensity. Shot Peener 28(2):30–38
18. Korsunsky AM (2017) A teaching essay on residual stresses and eigenstrains. Elsevier/Butterworth-Heinemann, Oxford
19. Lagoda T, Walat K (2014) Lifetime of semi-ductile materials through the critical plane approach. Int J Fatigue 67:73–710.1016/j.ijfatigue.2013.11.019 ↗
20. Lin J, Li W, Yang S, Zhang J (2018) Vibration fatigue damage accumulation of Ti-6Al-4V under constant and sequenced variable loading conditions. Metals 8(296):1–13
21. Liu Z, Zakoworotny M, Guo J, Zehnder AT, Hui C-Y (2020) Energy release rate of a single edge cracked specimen subjected to large deformation. Int J Fract 226:71–7910.1007/s10704-020-00479-7 ↗
22. Mangardich D, Abrari F, Fawaz Z (2019) A fracture mechanics based approach for the fretting fatigue of aircraft engine fan dovetail attachments. Int J Fatigue 129:10521310.1016/j.ijfatigue.2019.105213 ↗
23. Martín V, Vázquez J, Navarro C, Domínguez J (2020) Effect of shot peening residual stresses and surface roughness on fretting fatigue strength of Al 7075–T651. Tribol Int 142:10600410.1016/j.triboint.2019.106004 ↗
24. Murugesan J, Mutoh Y (2014) Fretting fatigue strength prediction of dovetail joint and bolted joint by using the generalized tangential stress range-compressive stress range diagram. Tribol Int 76:116–12110.1016/j.triboint.2013.11.006 ↗
25. Papanikos P, Meguid SA (1994) Theoretical and experimental studies of fretting-initiated fatigue failure of aeroengine compressor discs. Fatigue Fract Eng Mater Struct 17(5):539–55010.1111/j.1460-2695.1994.tb00253.x ↗
26. Papanikos P, Meguid SA, Stjepanovic Z (1998) Three-dimensional non-linear finite element analysis of dovetail joints in aero engine discs. Finite Element Anal Des 29:173–8610.1016/S0168-874X(98)00008-0 ↗
27. Pereira K, Vanegas-Useche LV, Wahab MA (2020) Aspects of fretting fatigue finite element modelling. Comput Mater Continua 64:97–14410.32604/cmc.2020.09862 ↗
28. Rajasekaran R, Nowell D (2006) Fretting fatigue in dovetail blade roots: experiment and analysis. Tribol Int 39:1277–8510.1016/j.triboint.2006.02.044 ↗
29. Sabelkin V, Martinez SA, Mall S, Sathish S, Blodgett MP (2005) Effects of shot-peening intensity on fretting fatigue crack-initiation behaviour of Ti-6Al-4V. Fract Eng Mater Struct 28:321–33210.1111/j.1460-2695.2005.00871.x ↗
30. Sun S, Li L, Yue Z, Yang W, He K, Li S (2020) Fretting fatigue failure behavior of Nickel-based single crystal superalloy dovetail specimen in contact with powder metallurgy pads at high temperature. Tribol Int 142:10598610.1016/j.triboint.2019.105986 ↗
31. Sunde SL, Haugen B, Berto F (2021) Experimental and numerical fretting fatigue using a new test fixture. Int J Fatigue 143:10601110.1016/j.ijfatigue.2020.106011 ↗
32. Simo JC, Laursen TA (1992) An augmented lagrangian treatment of contact problems involving friction. Comput Struct 42:97–11610.1016/0045-7949(92)90540-G ↗
33. Vantadori S, Zanichelli A (2020) Fretting-fatigue analysis of shot-peened aluminium and titanium test specimens. Fatigue Fract Eng Mater Struct. https://doi.org/10.1111/ffe.1336710.1111/ffe.13367 ↗
34. Vantadori S, Carpinteri A, Fortese G, Ronchei C, Scorza D, Zanichelli A (2018) Fatigue lifetime evaluation of notched components: implementation of the control volume concept in a strain-based LCF criterion. Theoret App Fract Mech 97:400–40810.1016/j.tafmec.2017.07.001 ↗
35. Vantadori S, Carpinteri A, Iturrioz I (2019) Fretting failure of a pressure armour in an unbonded flexible riser. Int J Fatigue 128:1–810.1016/j.ijfatigue.2019.105203 ↗
36. Vantadori S, Zanichelli A, Araújo JA (2020a) Fretting fatigue of 7050–T7451 Al alloy: the influence of bulk mean stress. Int J Fatigue 140:10581610.1016/j.ijfatigue.2020.105816 ↗
37. Vantadori S, Vázquez J, Zanichelli A (2020b) Fretting fatigue and shot peening: a multiaxial fatigue criterion including residual stress relaxation. Tribol Int 151:10653710.1016/j.triboint.2020.106537 ↗
38. Vázquez J, Navarro C, Domínguez J (2016) Two dimensional versus three dimensional modelling in fretting fatigue life prediction. J Strain Anal Eng Des 51:109–1710.1177/0309324715611510 ↗
39. Vázquez J, Carpinteri A, Bohórquez L, Vantadori S (2019) Fretting fatigue investigation on Al 7075–T651 alloy: experimental, analytical and numerical analysis. Tribol Int 135:478–8710.1016/j.triboint.2019.03.028 ↗
40. Yang Q, Zhou W, Zhong Y, Zhang X, Fu X, Chen G, Li Z (2018) Effect of shot-peening on the fretting wear and crack initiation behavior of Ti-6Al-4V dovetail joint specimens. Int J Fatigue 107:83–9510.1016/j.ijfatigue.2017.10.020 ↗
41. Yuan R, Liao D, Zhu SP, Yu ZY, Correia JAFO, de Jesus AMP (2021) Contact stress analysis and fatigue life prediction of turbine disc-blade attachment with fir-tree tenon structure. Fatigue Fract Eng Mater Struct. https://doi.org/10.1111/ffe.1341010.1111/ffe.13410 ↗
42. Zanichelli A, Vantadori S (2020) Shot-peened fretting fatigue components: endurance strength and fatigue life assessment. Mater Des Process Commun. https://doi.org/10.1002/mdp2.19610.1002/mdp2.196 ↗
43. Zhou ZR, Liu QY, Zhu MH, Tanjala L, Kapsa P, Vincent L (2000) An investigation of fretting behaviour of several metallic materials under grease lubrication. Tribol Int 33:69–7410.1016/S0301-679X(99)00100-0 ↗