journal article·2012-08

Influence of defects on fatigue strength and failure mechanisms in the VHCF-region for quenched and tempered steel and nodular cast iron

B. Pyttel, I. Brunner, D. Schwerdt, C. Berger

Publisher page

Abstract

Abstract Investigations are presented in this paper on quenched and tempered steel 42CrMoS4 from two batches, with two different tensile strengths (Rm = 1100 MPa, 1350 MPa) but with similar microstructure, and a nodular cast iron EN-GJS-900-2 (Rm = 930 MPa). Fatigue tests with smooth (Kt = 1) and notched (Kt = 1.75) specimens were performed at R = −1 and R = 0 up to the number of cycles N = 2·109 in order to determine the fatigue strength behaviour and failure mechanisms, especially in the VHCF-region. Failure in smooth specimens often initiated at material defects such as oxides in the quenched and tempered steel and shrinkage holes in the nodular cast iron. Firstly, a fatigue strength analysis was performed that did not consider these defects. A possibility of analysis of experimental data including VHCF-results has been discussed. Next, a linear elastic fracture mechanics analysis was performed in order to describe the defect behaviour, assuming that the defects act like cracks. The results showed that there are lower limit or threshold values of the stress intensity factor range ΔK for crack propagation in both materials. Analysis of defects and defect distribution in run-out specimens confirmed this conclusion. From the comparison of the results with an S–N curve from the design code FKM-Guideline Analytical strength assessment of components, recommendations for design and assessment of components have been derived.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fatigue and fracture mechanics · Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. FKM- Guideline Analytical strength assessment of components. 5th ed. Forschungskuratorium Maschinenbau. VDMA Verlag GmbH; 2003.
2. Eurocode 3. Design of Steel Structures, Part 1–9 fatigue. DIN EN 1993-1-9; 2005.
3. Eurocode 9. Design of aluminium structures, Part 2; 2001.
4. Hobbacher A, editor. Recommendations for fatigue design of welded joints and components. IIW document no. IIW-1823-07. International Institute of Welding. June; 2008.
5. 2001
6. 2004
7. 2007
8. Very high cycle fatigue – Is there a fatigue limit?10.1016/j.ijfatigue.2010.05.009 ↗
9. Schwerdt D, Pyttel B. Ermüdungsfestigkeit von Konstruktionswerkstoffen bei sehr hohen Schwingspielzahlen (Fatigue strength of engineering materials at very high number of cycles). FKM-Heft 304, Forschungskuratorium Maschinenbau e.V.; 2009.
10. Failure mechanisms of automotive metallic alloys in very high cycle fatigue range10.1016/j.ijfatigue.2005.09.019 ↗
11. The effect of inclusion geometry according to forging ratio and metal flow direction on very high-cycle fatigue properties of steel bars10.1016/j.ijfatigue.2007.10.009 ↗
12. Bathias · 2005
13. Manes L, Baudry G, Bathias C, Rathery S, Vittori JF, Doucet JP. Gigacyclic fatigue in engineering steels. VHCF-2, Wien; 2001.
14. Ochi Y, Matsumura T, Masaki K, Yoshida S. High cycle rotating bending fatigue property in very long life regime of high strength steels. VHCF-2, Wien; 2001.
15. Sternkopf J. Dauerfestigkeit von Gußeisenwerkstoffen bei Schwingspielzahlen >107. konstruieren+gießen 1994;19(3).
16. Ochi Y, Masaki K, Matsumura T, Hosoya T. Effect of shot peening treatment on very high cycle fatigue property in austempered ductile cast iron. VHCF-4, Ann Arbor; 2007.
17. ISO 945-1 Microstructure of cast irons – Part 1: graphite classification by visual analysis; 2008.
18. Haibach E, Betriebsfestigkeit, Verfahren und Daten zur Bauteilberechnung. 2. Auflage: Springer-Verlag Berlin Heidelberg; 2002.
19. Course of SN-Curves especially in the very high-cycle fatigue regime with regard to component design and safety10.1016/j.ijfatigue.2006.11.015 ↗
20. Dengel D. Die arcsin√p-Transformation – Ein einfaches Verfahren zur grafischen und rechnerischen Auswertung geplanter Wöhlerversuche. Z. f. Werkstofftechnik. J Mater Technol 6. Jahrg. 1975 / Nr. 8.10.1002/mawe.19750060803 ↗
21. Brunner I. Analyse der Defekte in einem Kugelgrafitguss und einem Vergütungsstahl zur Beurteilung deren Schädigungsrelevanz bei sehr hohen Schwingspielzahlen (Analysis of defects in a nodular cast iron and a quenched and tempered steel for evaluation of their significance for damage). Studienarbeit FH Frankfurt am Main; 2010.
22. Newman Jr JC, Raju IS. Stress-intensity factor equations for cracks in three-dimensional finite bodies subjected to tension and bending loads. NASA Technical Memorandum 85793. Lengley Research Center. Hampton, VA; 1984.10.1520/STP37074S ↗
23. Stress intensity factor equations for part-elliptical cracks and their verification10.1016/0013-7944(89)90246-4 ↗
24. FKM-Guideline Fracture Mechanics Proof of Strength for Engineering Components. 3rd ed. Forschungskuratorium Maschinenbau. VDMA Verlag GmbH; 2009.