journal article·2025-04Open access

Deformation mechanisms at the tip of internal fatigue cracks in vacuum and in the presence of an air environment in a Ti alloy

Louis Hébrard, Thierry Palin-Luc, Nicolas Ranc, Arnaud Weck, Thierry Douillard, Nicholas Blanchard, Sylvain Dancette, Jean-Yves Buffiere

Abstract

Ultrasonic fully reversed tension fatigue tests have been performed in the Very High Cycle Fatigue (VHCF) regime ( N R > 1 0 7 − 1 0 8 c y c l e s ) on Ti-6Al4V specimens containing a controlled internal notch. Two sets of samples have been used. The first one contains a central chimney along the specimen longitudinal axis which brings air to the internal notch; in the second series the notches are not connected to the surface. The microstructure present below the fracture surface of the broken specimens has been studied by electron microscopy (EBSD, TKD and TEM). The formation of nanograins and nanovoids was observed below the surface of the cracks growing in a vacuum environment but not below the surface of cracks connected with ambient air. In the latter case extensive striations were observed. Below each striation the formation of tensile {10 1 ̄ 2} twins was observed. • Fatigue samples with sharp internal defects with or without connection with air are tested. • Growth mechanisms of internal crack are observed with or without air at the crack tip. • Striation marks are observed on the internal crack surfaces propagating in air. • No striation marks are observed on the internal crack surfaces growing in vacuum. • Twins are observed below the striation for the cracks growing in air.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Fatigue and fracture mechanics · Material Properties and Failure Mechanisms · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (60)

Show source-provided references
1. The nature and the mechanism of crack initiation and early growth for very-high-cycle fatigue of metallic materials – An overview10.1016/j.tafmec.2017.05.002 ↗
2. On the mechanism of very high cycle fatigue in Ti–6Al–4V10.1016/j.scriptamat.2008.08.012 ↗
3. Effects of stress ratio on high-cycle and very-high-cycle fatigue behavior of a Ti–6Al–4V alloy10.1016/j.msea.2014.09.115 ↗
4. Fatigue crack propagation properties of Ti–6Al–4V in vacuum environments10.1016/j.ijfatigue.2012.02.012 ↗
5. Observations of facet formation in near-α titanium and comments on the role of hydrogen:
6. Investigation of fatigue crack initiation facets in Ti-6Al-4V using focused ion beam milling and electron backscatter diffraction: Investigation of crack initiation facets10.1111/jmi.12547 ↗
7. Effect of vacuum pressure on small crack propagation in Ti-6Al-4V10.1016/j.ijfatigue.2020.105961 ↗
8. A review on fatigue fracture modes of structural metallic materials in very high cycle regime10.1016/j.ijfatigue.2016.05.029 ↗
9. Very-high-cycle fatigue behavior of a structural steel with and without induced surface defects10.1016/j.ijfatigue.2016.05.032 ↗
10. An experimental investigation of fatigue performance and crack initiation characteristics for an SLMed Ti-6Al-4V under different stress ratios up to very-high-cycle regime10.1016/j.ijfatigue.2022.107119 ↗
11. Crack initiation mechanisms of Ti6Al4V in the very high cycle fatigue regime10.1016/j.ijfatigue.2016.04.026 ↗
12. Nanograin layer formation at crack initiation region for very-high-cycle fatigue of a Ti-6Al-4V alloy: Nanograin Formation for VHCF of TI Alloy10.1111/ffe.12562 ↗
13. Microstructure refinement and grain size distribution in crack initiation region of very-high-cycle fatigue regime for high-strength alloys10.1016/j.ijfatigue.2020.105473 ↗
14. On the mechanism of fatigue failure in the superlong life regime (N>107 cycles). Part 1: influence of hydrogen trapped by inclusions10.1046/j.1460-2695.2000.00328.x ↗
15. Effects of inclusions on very high cycle fatigue properties of high strength steels10.1179/1743280411Y.0000000008 ↗
16. Environment effect on internal fatigue crack propagation studied with in-situ X-ray microtomography10.1016/j.msea.2023.145462 ↗
17. Hébrard · 2023
18. Lunt · 2014
19. Fabrication of artificial defects to study internal fatigue crack propagation in metals10.1016/j.scriptamat.2019.05.018 ↗
20. Internal fatigue crack propagation in a Ti-6Al-4V alloy: An in situ study10.1016/j.ijfatigue.2022.107450 ↗
21. Cracking evolution behaviors of lightweight materials based on in situ synchrotron X-ray tomography: A review10.1007/s11465-018-0481-2 ↗
22. Characterization of internal fatigue crack initiation in Ti-6Al-4V alloy via synchrotron radiation X-ray computed tomography
23. Detection of small internal fatigue cracks in Ti-6Al-4V via synchrotron radiation nanocomputed tomography10.1111/ffe.13765 ↗
24. In situ synchrotron ultrasonic fatigue testing device for 3D characterisation of internal crack initiation and growth
25. A critical review of orientation microscopy in SEM and TEM10.1002/crat.201100125 ↗
26. Transmission EBSD from 10 nm domains in a scanning electron microscope10.1111/j.1365-2818.2011.03566.x ↗
27. Orientation mapping of nanostructured materials using transmission Kikuchi diffraction in the scanning electron microscope10.1016/j.ultramic.2012.06.004 ↗
28. Nanometres-resolution Kikuchi patterns from materials science specimens with transmission electron forward scatter diffraction in the scanning electron microscope10.1111/jmi.12007 ↗
29. Orientation and phase mapping in the transmission electron microscope using precession-assisted diffraction spot recognition: state-of-the-art results10.1111/jmi.12065 ↗
30. Application of transmitted Kikuchi diffraction in studying nano-oxide and ultrafine metallic grains10.1021/acsnano.5b04296 ↗
31. Grain coarsening of nano laminated structure in martensite steel under sliding wear10.1016/j.triboint.2020.106381 ↗
32. Mechanism of mean stress sensitivity in Ti-6Al-4V under different stress ratios in high cycle fatigue10.1016/j.ijfatigue.2024.108268 ↗
33. Strength, grain refinement and solute nanostructures of an Al–Mg–Si alloy (AA6060) processed by high-pressure torsion10.1016/j.actamat.2013.10.022 ↗
34. Fine granular area formation by damage-induced shear strain localization in very-high-cycle fatigue10.1111/ffe.13529 ↗
35. Examining the role of water vapor on small fatigue crack growth behavior in Ti-6242S using ultrasonic fatigue and scanning electron microscopy10.1016/j.ijfatigue.2021.106672 ↗
36. Determination of crystallographic orientation of dwell-fatigue fracture facets in Ti-6242 alloy10.1007/s10853-006-0252-z ↗
37. Determination of the orientation of Cu-Bi grain boundary facets using a photogrammetric technique10.1016/1044-5803(90)90069-V ↗
38. Low ΔK faceted crack growth in titanium alloys10.1016/j.ijfatigue.2008.03.036 ↗
39. Junet · 2021
40. Concurrent operation of c + a slip and twinning under cyclic loading of Ti-6Al-4V10.1016/j.scriptamat.2018.07.033 ↗
41. Characterization of fatigue crack-initiation facets in relation to lifetime variability in Ti–6Al–4V10.1016/j.ijfatigue.2011.11.017 ↗
42. New insights into microstructure refinement in crack initiation region of very-high-cycle fatigue for SLM Ti-6Al-4V via precession electron diffraction10.1016/j.mtla.2024.102008 ↗
43. The formation mechanism of characteristic region at crack initiation for very-high-cycle fatigue of high-strength steels10.1016/j.ijfatigue.2015.11.029 ↗
44. Autonomous healing of fatigue cracks via cold welding10.1038/s41586-023-06223-0 ↗
45. Environmentally assisted fatigue in the gaseous atmosphere10.1016/B978-0-12-822944-6.00031-1 ↗
46. Characterization of surface oxide films on titanium and bioactivity10.1023/A:1014737831371 ↗
47. Formation mechanism of the distinctive granular fracture surface in subsurface fracture of Ti6Al4V alloy10.1016/j.mtla.2021.101312 ↗
48. On the correlation between fatigue striation spacing and crack growth rate: A three-dimensional (3-D) X-ray synchrotron tomography study10.1007/s11661-011-0963-x ↗
49. Nanograin formation mechanism under fatigue loadings in additively manufactured Ti-6Al-4V alloy10.1016/j.ijfatigue.2023.107821 ↗
50. Effective structural unit size in titanium alloys10.1243/03093247JSA273 ↗
51. Deformation twinning in fatigue crack tip plastic zone of Ti-6Al-4V alloy with Widmanstatten microstructure10.1016/j.matchar.2017.08.029 ↗
52. Nanograin formation and cracking mechanism in Ti alloys under very high cycle fatigue loading10.1016/j.ijfatigue.2022.107331 ↗
53. Orientation dependence of slip and twinning in HCP metals10.1016/S1359-6462(97)00048-1 ↗
54. Dancette · 2024
55. The theory of the crystallography of deformation twinning
56. Crystal plasticity modeling of texture development and hardening in TWIP steels10.1016/j.actamat.2012.01.015 ↗
57. Plastic behavior of the α′ phase in Ti-6Al-4V alloys10.1016/j.matlet.2020.128719 ↗
58. Crystal plasticity modeling of slip activity in Ti–6Al–4V under high cycle fatigue loading10.1016/j.ijplas.2008.08.004 ↗
59. In situ analysis of plasticity and damage nucleation in a Ti-6Al-4V alloy and laser weld10.1016/j.matchar.2018.09.039 ↗
60. On the mechanistic basis of deformation at the microscale in hexagonal close-packed metals10.1098/rspa.2014.0881 ↗