Influence of hammer peening on fatigue life of E309L steel used for 13%Cr-4%Ni blade runner repairs
Source abstract
Abstract
Abstract Austenitic stainless steel E309L is frequently used for welded repairs on 13%Cr-4%Ni martensitic stainless steel blade runners. However, very high tensile residual stresses are found in the upper layers of these repairs, thus reducing the fatigue resistance of the repaired area in comparison with the free of residual stress base material. The use of hammer peening to increase the fatigue life of E309L welded on UNS-S41500 base metal plates has been investigated using welded samples replicating in situ blade runner repairs. Residual stress measurements using the contour method on these samples have confirmed the high stresses caused by flux cored arc welding (FCAW) of E309L, leaving stress magnitudes close to the ultimate tensile strength of the base material. Hammer peening of the surface beads effectively creates high compressive stresses at the weld’s surface up to 3 mm depth. Alternating bending fatigue tests conducted on hammer peened samples have shown an average life increase of 5.8 times at Sa = 330 MPa over unpeened samples. Fatigue tests have however shown diminishing returns when overpeening the samples.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Surface Treatment and Residual Stress · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. A comparison of residual stress in Hammer-peened, multi-pass steel welds–A514 (S690Q) and S4150010.1007/BF03266717 ↗
2. Trufyakov · 1995
3. Dowling NE. Mechanical behavior of materials: engineering methods for deformation, fracture, and fatigue, 4th ed., Pearson Education; 2013.
4. Nasri H, Champliaud H. Mesure de contraintes résiduelles dues au soudage et au soudage-martelage par micro-profil de surface. In, École de technologie supérieure; 2007.
5. Evaluation of residual stresses induced by robotized hammer peening by the contour method10.1007/s11340-008-9205-6 ↗
6. Adjassoho B, Kozeschnik E, Lechner C, Bleicher F, Goessinger S, Bauer C. Induction of residual stresses and increase of surface hardness by machine Hammer peening technology. In: Annals of DAAAM for 2012 & proceedings of the 23rd international DAAAM symposium; 2012. p. 697–702 [ISBN].10.2507/23rd.daaam.proceedings.163 ↗
7. Fatigue behaviour of welded joints with cracks, repaired by hammer peening10.1111/j.1460-2695.2004.00777.x ↗
8. The influence of hammer peening on fatigue in high-strength steel10.1016/0142-1123(91)90483-F ↗
9. Efficiency of improvement techniques on the fatigue strength as a function of the type of welded joint
10. Fatigue strength improvement by hammer peening treatment—verification from plastic deformation, residual stress, and fatigue crack propagation rate10.1007/s40194-014-0115-1 ↗
11. Fatigue strength improvement factors for high strength steel welded joints treated by high frequency mechanical impact10.1016/j.ijfatigue.2012.05.002 ↗
12. Nakano T, Nakanishi K, Morikage Y. Method of improving fatigue strength by peening on base metal and development of mechanized system. In: Corporation JS, editor. JFE Technical Report; 2015.
13. Almar-Naess · 1985
14. Lanteigne J, Baillargeon C, Marcouiller L. Mesure de la résistance à la fatigue de certains aciers utilisés dans la fabrication et la réparation de roues de turbines hydrauliques; 2001. p. 60.
15. Comportement des fissures de fatigue dans un champ de contraintes résiduelles de tension
16. Thibault D, Simoneau R, Lanteigne J, Fihey JL. Residual stresses induced by robotized hammer-peening. In: Materials science forum. Trans Tech Publ; 2005. p. 352–7.10.4028/0-87849-969-5.352 ↗
17. Cross-sectional mapping of residual stresses by measuring the surface contour after a cut10.1115/1.1345526 ↗
18. Known residual stress specimens using opposed indentation10.1115/1.3120386 ↗
19. Prime MB, Hughes DJ, Webster PJ. Weld application of a new method for cross-sectional residual stress mapping. In: 2001 SEM annual conf on experimental and applied mechanics, Portland, OR; 2001. p. 608–11.
20. Lévesque · 2015
21. Measuring multiple residual-stress components using the contour method and multiple cuts10.1007/s11340-009-9280-3 ↗
22. Nakazawa H, Kodama S. Statistical S-N testing method with 14 specimens: JSME standard method for determination of S-N curves. In: Statistical research on fatigue and fracture, Elsevier Applied Science Publishers, London, UK; 1987. p. 59–69.
23. An experimental comparison of weld-induced residual stresses using different stainless steel filler metals commonly used for hydraulic turbines manufacturing and repair
24. Juvinall · 2006
25. Haagensen PJ. 11. Fatigue strength improvement methods. In: Macdonald KA, editor. Fracture and fatigue of welded joints and structures. Woodhead Publishing; 2011.10.1533/9780857092502.2.297 ↗