Effect of high frequency impacting and rolling on fatigue crack growth of 2A12 aluminum alloy welded joint
Source abstract
Abstract
Abstract The influence of high frequency impacting and rolling (HFIR) on fatigue crack growth (FCG) of welded joint were researched. Results showed that grain sizes of the top surface of BM and WS were refined; Both the nanomicrohardness, elastic modulus and maximum compressive residual stress (CRS) were increased. The introduction of near-surface CRS leads to obvious changes of the surface actual stress situation, increases the crack closure and decreases the stress intensity factor of crack tip. FCG life of BM and WS increased by 1.594~1.744 times and 2.902~3.231 times. BM and WS exhibited a different fracture characterized before and after HFIR.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Surface Treatment and Residual Stress
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Research on laser welding of high-strength galvanized automobile steel sheets10.1016/j.optlaseng.2009.06.016 ↗
2. Effect of welding wires on microstructure and mechanical properties of 2A12 aluminum alloy in CO2 laser-MIG hybrid welding10.1016/j.apsusc.2009.03.088 ↗
3. Effect of graphene oxide on anticorrosion performance of polyelectrolyte multilayer for 2A12 aluminum alloy substrates10.1039/C7RA90082A ↗
4. Improving Joint Features and Mechanical Properties of Pinless Fiction Stir Welding of Alcald 2A12-T4 Aluminum Alloy10.1016/j.jmst.2016.07.003 ↗
5. Additive manufacturing of metallic components-Process, structure and properties10.1016/j.pmatsci.2017.10.001 ↗
6. J Legat, S Sedmak, B Petrovski. Influence of initial Plastic Deformation in Weld Fatigue Crack Growth Icbmff3, 2013.
7. Residual stress effects on fatigue crack growth in a Ti-6Al-4V friction stir weld10.1111/j.1460-2695.2008.01258.x ↗
8. Sharp · 1996
9. Influence of severe plastic deformation on fatigue life applied by ultrasonic peening in welded pipe 316 Stainless Steel joints in corrosive environment10.1016/j.ultras.2018.03.012 ↗
10. The effects of ultrasonic peening treatment on the ultra-long life fatigue behavior of welded joints10.1016/j.matdes.2010.02.006 ↗
11. A comprehensive investigation on the effects of laser and shot peening on fatigue crack growth in friction stir welded AA 2195 joints10.1016/j.ijfatigue.2008.03.029 ↗
12. Laser and shot peening effects on fatigue crack growth in friction stir welded 7075–T7351 aluminum alloy joints10.1016/j.ijfatigue.2006.05.007 ↗
13. Study on fatigue crack growth performance of EH36 weldments by laser shock processing10.1016/j.surfin.2018.10.009 ↗
14. Zhang L, Zhong H, Li S, et al. Microstructure, mechanical properties and fatigue crack growth behavior of friction stir welded joint of 6061-T6 aluminum alloy. Int J Fatigue 135.10.1016/j.ijfatigue.2020.105556 ↗
15. Effect of the precipitated phase of MgZn2 on surface nanocrystallization of Al-Zn-Mg alloy based on high-frequency impacting and rolling
16. New insight into high frequency impacting and rolling of 2A12 aluminum welded joint involving nanocrystallization10.1016/j.apsusc.2019.05.234 ↗
17. Surface Characteristics and Fatigue Behavior of Gradient Nano-Structured Magnesium Alloy10.3390/met7020062 ↗
18. Gradient crystalline structure induced by ultrasonic impacting and rolling and its effect on fatigue behavior of TC11 titanium alloy10.1016/j.rinp.2017.05.026 ↗
19. Research on friction and wear behavior of gradient nano-structured 40Cr steel induced by high frequency impacting and rolling10.1016/j.engfailanal.2017.09.012 ↗
20. Influence of High-Frequency Impacting and Rolling on Friction and Wear Behavior of 2A12 Aluminum Alloy
21. Research on friction and wear behavior of gradient nano-structured 40Cr steel induced by high frequency impacting and rolling10.1016/j.engfailanal.2017.09.012 ↗
22. Fatigue properties and crack behavior of ultra-fine and nanocrystalline pure metals10.1016/j.ijfatigue.2009.05.004 ↗
23. Fracture behaviour of ultrafine-grained materials under static and cyclic loading. Int
24. Fatigue properties of 5056 Al-Mg alloy produced by equal-channel angular pressing10.1016/S0965-9773(99)00392-X ↗
25. Improvement of high-cycle fatigue life in a 6061 Al alloy produced by equal channel angular pressing
26. Microstructure evolution and fatigue behavior of 2124 aluminum processed by ECAE with back pressure10.1016/j.msea.2006.03.023 ↗
27. Influence of microstructure on fatigue crack propagation behaviors of an aluminum alloy: role of sheet thickness10.1016/j.engfracmech.2017.05.038 ↗
28. Quantitative analysis of micro-structural effects on fatigue crack growth in widmanstatter Ti6Al4V and Ti8Al1-MolV10.1016/0013-7944(79)90138-3 ↗
29. Effect of laser peening with different energies on fatigue fracture evolution of 6061–T6 aluminum alloy10.1016/j.optlastec.2015.09.008 ↗
30. Electron fractographic studies of mechanical fracture processes in metals