High cycle fatigue behavior of high-Mn TWIP steel with different surface morphologies
Source abstract
Abstract
Abstract Cyclic deformation behavior and fatigue life of high-Mn TWIP steel with different surface morphologies was investigated. Specimens with different surface morphologies, namely polished, down and up milled, were loaded in the HCF regime. The surface morphologies were analyzed by cyclic indentation tests, XRD, SEM and FIB methods. Milling led to differences in topographies, residual stresses and microstructures. Fatigue tests at various stress amplitudes were conducted in the HCF regime, investigating how these surface morphologies affect the cyclic deformation behavior and consequently fatigue life. The results show a significant influence of the surface morphologies on the material’s behavior under cyclic loading.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal and Thin Film Mechanics · Surface Treatment and Residual Stress
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. Twinning-induced plasticity (TWIP) steels10.1016/j.actamat.2017.06.046 ↗
2. Development of high-manganese TWIP steels and application examples in highfrequency welded automotive designs
3. Development of high Mn steel metallurgy for erosion resistant slurry pipeline
4. Influence of addition elements on the stacking-fault energy and mechanical properties of an austenitic Fe–Mn–C steel10.1016/j.msea.2006.12.170 ↗
5. Phase transformation and deformation behavior of steels with different content of metastable austenite
6. Grain size effect on strain hardening in twinning-induced plasticity steels10.1016/j.scriptamat.2012.01.037 ↗
7. Microstructure evolution and strengthening mechanisms of Fe–23Mn–0.3C–1.5Al TWIP steel during cold rolling10.1016/j.msea.2014.08.051 ↗
8. The influence of stacking fault energy on the microstructural and strain-hardening evolution of Fe–Mn–Al–Si steels during tensile deformation10.1016/j.actamat.2015.08.030 ↗
9. High strength Fe–Mn–(Al, Si) TRIP/TWIP steels development - properties - application10.1016/S0749-6419(00)00015-2 ↗
10. Prediction of the local deformation mechanisms in metastable austenitic steels from the local concentration of the main alloying elements10.1016/j.matlet.2015.06.087 ↗
11. High manganese austenitic twinning induced plasticity steels10.1016/j.cossms.2011.04.002 ↗
12. Derivation and variation in composition-dependent stacking fault energy maps based on subregular solution model in high-manganese steels10.1007/s11661-009-0050-8 ↗
13. The influence of manganese content on the stacking fault and austenite/ε-martensite interfacial energies in Fe–Mn–(Al–Si) steels investigated by experiment and theory10.1016/j.actamat.2014.01.001 ↗
14. Stacking fault energies of Mn, Co and Nb alloyed austenitic stainless steels10.1016/j.actamat.2011.05.049 ↗
15. Influence of temperature on phase transformation and deformation mechanisms of cast CrMnNi-TRIP/TWIP steel10.4028/www.scientific.net/SSP.172-174.172 ↗
16. Effect of temperature and strain rate on strain hardening and deformation mechanisms of high manganese austenitic steels10.3139/146.110333 ↗
17. Deformation mechanisms in austenitic TRIP/TWIP steel as a function of temperature10.1007/s11661-014-2684-4 ↗
18. Low cycle fatigue behavior and deformation mechanism of TWIP steel10.1016/S1006-706X(14)60054-6 ↗
19. Low cycle fatigue and deformation behaviour of austenitic manganese steel in rolled and in as-cast conditions10.1016/j.proeng.2010.03.067 ↗
20. Low-cycle and extremely-low-cycle fatigue behaviors of high-Mn austenitic TRIP/TWIP alloys10.1016/j.actamat.2015.11.015 ↗
21. Surface morphology and its influence on cyclic deformation behavior of high-Mn TWIP steel10.3390/met8100832 ↗
22. Influence of the surface morphology on the cyclic deformation behavior of HSD® 600 steel10.1051/matecconf/201816506010 ↗
23. High-cycle fatigue behavior of ultrafine-grained austenitic stainless and TWIP steels10.1016/j.msea.2010.05.035 ↗
24. Fatigue behavior of four high-Mn twinning induced plasticity effect steels10.1007/s11661-010-0193-7 ↗
25. Fatigue behavior of high-Mn TWIP steels10.1016/j.msea.2009.03.039 ↗
26. Tensile and high cycle fatigue behaviors of high-Mn steels at 298 and 110 K10.1016/j.matchar.2016.12.001 ↗
27. Formation of nanostructured surface layer on AISI 304 stainless steel by means of surface mechanical attrition treatment10.1016/S1359-6454(02)00594-3 ↗
28. Influence of surface morphology on the very high cycle fatigue behavior of metastable and stable austenitic Cr-Ni steels10.1051/matecconf/201816520008 ↗
29. Microstructural characterization of cyclic deformation behavior of metastable austenitic stainless steel AISI 347 with different surface morphology10.1557/jmr.2017.318 ↗
30. Influence of surface morphology on the fatigue behavior of metastable austenitic steel10.4028/www.scientific.net/AMR.891-892.464 ↗
31. Influence of surface morphology on fatigue behavior of metastable austenitic stainless steel AISI 347 at ambient temperature and 300°C
32. Improvement of low-cycle fatigue resistance in TWIP steel by regulating the grain size and distribution10.1016/j.actamat.2017.05.004 ↗
33. Improving the high-cycle fatigue properties of twinning-induced plasticity steel by a novel surface treatment process10.1016/j.msea.2018.10.046 ↗
34. Cyclic hardness test PHYBALCHT – Short-time procedure to evaluate fatigue properties of metallic materials10.1016/j.ijfatigue.2014.01.009 ↗
35. Tailoring the hardening behavior of 18CrNiMo7-6 via Cu alloying10.1002/srin.201500129 ↗
36. Investigation of the anisotropic fatigue behavior of additively manufactured structures made of AISI 316L with short-time procedures PhyBaLLIT and PhyBaLCHT10.1016/j.ijfatigue.2019.03.022 ↗
37. Indentation properties of plasma sprayed Al2O3–13% TiO2 nanocoatings10.1016/j.actamat.2009.03.020 ↗
38. Indentation size effect in MgO10.1016/j.scriptamat.2004.05.034 ↗
39. Indentation size effect in metallic materials: correcting for the size of the plastic zone10.1016/j.scriptamat.2005.02.009 ↗
40. Study on the indentation size effect in CaF2: dislocation structure and hardness10.1016/j.actamat.2008.11.015 ↗
41. The correlation of indentation experiments
42. On the tensile behavior of high-manganese twinning-induced plasticity steel10.1007/s11661-009-9992-0 ↗
43. Strain hardening rate sensitivity and strain rate sensitivity in TWIP steels10.1016/j.msea.2015.01.080 ↗
44. PhyBaLCHT – influence of indentation force on the results of cyclic hardness tests and investigations of comparability to uniaxial fatigue loading10.1016/j.ijfatigue.2018.09.025 ↗
45. Characterization of cyclic deformation behaviour by mechanical, thermometrical and electrical methods10.1002/mawe.19950260305 ↗
46. Inclusion rating by statistics of extreme values and its application to fatigue strength prediction and quality control of materials