On the strain-induced martensitic transformation process of the commercial AISI 304 stainless steel during cyclic loading
Source abstract
Abstract
Abstract Low-cycle fatigue tests were performed on metastable austenitic steel at two initial material states, the as-received, with a high crystal defect density, and the solution treated one, with fewer crystal defects. Cyclic curves have shown different hardening behavior depending on the initial material states. To understand these differences, the back and friction stresses were studied from the hysteresis loop analysis. The correlation of these results with the volume fraction of induced martensite and the observed microstructure revealed that the cyclic hardening behavior strongly depends on the existence of potential martensite nucleation sites.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. Study of stainless steel bolted extended end-plate joints under seismic loading10.1016/j.tws.2019.106255 ↗
2. Proposal of residual stress mitigation in nuclear safety-related austenitic stainless steel TP304 pipe bended by local induction heating process via elastic-plastic finite element analysis10.1016/j.net.2019.03.007 ↗
3. Fabrication of nanostructure in inner-surface of AISI 304 stainless steel pipe with surface plastic deformation10.1016/j.jmst.2018.05.012 ↗
4. Evaluation method of corrosion lifetime of conventional stainless steel canister under oceanic air environment10.1016/j.nucengdes.2007.03.040 ↗
5. Effect of γ to ε martensitic transformation on low-cycle fatigue behaviour and fatigue microstructure of Fe–15Mn–10Cr–8Ni–xSi austenitic alloys10.1016/j.actamat.2015.12.002 ↗
6. Effects of Strain State and Strain Rate on Deformation-Induced Transformation in 304 Stainless Steel: Part I. Magnetic Measurements and Mechanical Behavior10.1007/BF02644427 ↗
7. Transformation mechanism of α′-martensite in an austenitic Fe–Mn–C–N alloy10.1016/j.scriptamat.2007.05.003 ↗
8. Formation of shear bands and strain-induced martensite during plastic deformation of metastable austenitic stainless steels10.1016/j.actamat.2007.07.015 ↗
9. Morphologies and characteristics of deformation induced martensite during low cycle fatigue behaviour of austenitic stainless steel10.1016/j.msea.2011.07.011 ↗
10. The influence of metallurgical factors on corrosion fatigue strength of stainless steels10.1016/j.prostr.2016.06.067 ↗
11. Deformation-induced martensite formation during cyclic deformation of metastable austenitic steel: Influence of temperature and carbon content10.1016/j.msea.2006.12.211 ↗
12. Kain, V., 2011. Stress corrosion cracking (SCC) in stainless steels, in: Stress Corrosion Cracking. Elsevier, pp. 199–244. https://doi.org/10.1533/9780857093769.3.199.10.1533/9780857093769.3.199 ↗
13. Influence of carbon concentration on martensitic transformation in metastable austenitic steels under cyclic loading conditions10.1016/S0921-5093(01)01087-5 ↗
14. Monitoring fatigue degradation in austenitic stainless steels10.1111/j.1460-2695.2004.00784.x ↗
15. Influencing parameters on martensite transformation during low cycle fatigue for steel AISI 32110.1016/j.msea.2006.04.077 ↗
16. Adjusting the very high cycle fatigue properties of a metastable austenitic stainless steel by means of the martensite content10.1016/j.proeng.2010.03.179 ↗
17. Microstructural investigation of the fatigue behavior and phase transformation in metastable austenitic steels at ambient and lower temperatures10.1016/j.ijfatigue.2012.07.004 ↗
18. Soares, G.C., Rodrigues, M.C.M., Santos, L. de A., 2017. Influence of Temperature on Mechanical Properties, Fracture Morphology and Strain Hardening Behavior of a 304 Stainless Steel. Materials Research 20, 141–151. https://doi.org/10.1590/1980-5373-mr-2016-0932.10.1590/1980-5373-mr-2016-0932 ↗
19. A profile refinement method for nuclear and magnetic structures10.1107/S0021889869006558 ↗
20. Lutterotti, L., Matthies, S. and Wenk, H.R., 1999. MAUD: a friendly Java program for material analysis using diffraction. IUCr: Newsletter of the CPD, 21(14-15).
21. Low-cycle fatigue behavior in metastable austenitic steel accompanying deformation-induced martensitic transformation10.2355/isijinternational1966.23.834 ↗
22. Plasticity-induced martensitic transformation during cyclic deformation of AISI 304L stainless steel10.1016/0921-5093(89)90871-X ↗
23. Fatigue short crack behaviour in metastable austenitic stainless steels with different grain sizes10.1016/S0921-5093(01)01072-3 ↗
24. U. Krupp, I. Roth, H-J Christ, M. Kübbeler, C-P Fritzen. On the Mechanism of Martensite Formation during Short Fatigue Crack Propagation in Austenitic Stainless Steel: Experimental Identification and Modelling Concept. 13th International Conference on Fracture June 16–21, 2013, Beijing, China.
25. KOEHLER, J.S., 1954. Dislocations and Plastic Flow in Crystals. A. H. Cottrell. Oxford Univ. Press, New York, 1954. Science 119, 551–551. https://doi.org/10.1126/science.119.3095.551.10.1126/science.119.3095.551-a ↗
26. Dislocation behavior in fatigue II. Friction stress and back stress as inferred from an analysis of hysteresis loops10.1016/0025-5416(79)90074-0 ↗
27. A comparison of two simple methods for measuring cyclic internal and effective stresses10.1016/0025-5416(84)90083-1 ↗
28. A.F. Armas, I. Alvarez-Armas, G. Degallaix, S. Degallaix. In: Roberti. R, editor. Duplex 2000, 2000, p. 183.
29. On the cyclic softening behavior of SAF 2507 duplex stainless steel10.1016/j.actamat.2006.06.037 ↗