Fatigue properties of steel to aluminum transition joints produced by explosion welding
Source abstract
Abstract
This manuscript presents the results of designing and testing a novel fixturing device for determining the fatigue properties of explosive bonded metals. The fatigue strength of steel to aluminum transition joints in tensile and compression stresses are presented. Additionally, shear stress for different load ratios was also studied. The stress distribution in the specimens was verified by finite element analysis. The experimental tensile/compressive fatigue results show a comparable fatigue lifetime to the recommended IIW values. The shear fatigue strength of the explosion-welded junction tested in this study is equivalent to a traditional butt welded joint.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Mechanical Behavior of Composites · Intermetallics and Advanced Alloy Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (16)
Show source-provided references
1. Young G, Banker J. Explosion welded, bi-metallic solution to dissimilar metal joining. In: Proceedings of the 13th offshore symposium 2004, February 24, Houston, Texas, Texas Section of the Society of Naval Architects and Marine Engineers. p. 6.
2. Farhadi Sartangi P. Effect of post-weld heat treatment on the interface microstructure of explosively welded titanium–stainless steel composite10.1016/j.msea.2008.04.032 ↗
3. An investigation of mechanical and metallurgical properties of explosive welded aluminum–dual phase steel10.1016/j.matlet.2008.05.060 ↗
4. Zhou, B. bin; Zhou, C. yu; Chang, L.; Yu, X. chun; Ye, C.; Zhang, B. jun: Investigation on fatigue crack growth behavior of Zr702/TA2/Q345R explosive welding composite plate with a through-wall crack. Compos. Struct. 2020, 236, 111845.10.1016/j.compstruct.2019.111845 ↗
5. Fatigue phenomena in explosively welded steel-titanium clad components10.1016/j.ijfatigue.2012.10.007 ↗
6. Special features of failure of bimetal in low-cycle fatigue10.1007/BF01530180 ↗
7. Evaluation of interfacial crack growth in biomaterial metallic joints loaded by symmetric three-point bending10.1016/S0308-0161(03)00004-8 ↗
8. Hobbacher A. Recommendations for Fatigue Design of Welded Joints and Components. IIW-document XIII-2460-13.
9. S. Liu, J. Banker, and C. Prothe, Explosion Welding, Welding Fundamentals and Processes, Vol 6A, ASM International, 2011.
10. High cooling rates and metastable phases at the interfaces of explosively welded materials10.1016/j.actamat.2017.06.038 ↗
11. Explosive Weld Interface Characterization - Complex Microstructure & Solidification Details10.1017/S1431927612010227 ↗
12. Explosion-bonded metals for marine structural applications
13. MIL-J-24445A, Military Specification: Joint, Bimetallic Bonded, Aluminum to Steel (25 JUL 1977).
14. Moore, S. and Banker, J, “Aluminum Steel Construction in a New 36M [120 Ft] Patrol Boat”; Proceedings of the Ship Production Symposium, held in New Orleans, Louisiana, on 2-4 September 1992.
15. Ranker, J.G. and Gaines E-T., “Shipboard Aluminum/Steel Welded Transition Joints Evaluation and Improvements,” 1990 Ship Production Symposium, Milwaukee, WI, sponsored by Society of Naval Architects and Marine Engineers.
16. Ranker, J.G. and Gaines E.T. “Shipboard Aluminum/Steel Welded Transition Joints,” 1991 Ship Production Symposium, San Diego, CA, sponsored by Society of Naval Architects and Marine Engineers.