Fixing a hole (with cold spray)
Source abstract
Abstract
Abstract Continuous development of cold spray technology, resulting in better mechanical properties, enables extension of cold spray application to components carrying loads. As a new subject, no standard procedures to assess fatigue life of repaired parts are available. Here, we propose new specimen for axial fatigue test to simulate behaviour of parts with localized damage and repaired with cold spray, which are subjected to cyclic loading. The specimen includes a cavity representing spray bed machined around the damage to permit cold spraying. The geometry of the specimen was based on coating quality and stress analysis, which are both discussed in this study. Specimen, produced from A357 aluminum alloy, was successfully tested and can be used as a part of standard procedure for mechanical testing of structural repairs. Moreover, fatigue limit obtained on repaired specimens corresponds to the limit obtained on bulk material, which proves potential of cold spray for restoration of structural parts.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Coal Combustion and Slurry Processing · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. The Welding Institute Website; 2017. [accessed 13 April 2017].
2. Kay · 2016 · 300
3. Champagne VK. The cold spray materials deposition process: fundamentals and applications, 1st ed. Woodhead Publishing; 2007. p. 376.10.1533/9781845693787.1 ↗
4. Villafuerte J. Modern cold spray: materials, process, and applications, 1st ed. Springer International Publishing; 2015. p 429.10.1007/978-3-319-16772-5 ↗
5. Adiabatic shear instability based mechanism for particles/substrate bonding in the cold-gas dynamic-spray process10.1016/j.matdes.2004.03.008 ↗
6. On parameter selection in cold spraying10.1007/s11666-011-9662-9 ↗
7. Correlation of impact conditions, interface reactions, microstructural evolution, and mechanical properties in kinetic spraying of metals: a review10.1007/s11666-016-0448-y ↗
8. CORSAIR; 2016. [accessed 13 April 2017].
9. Effect of cold spray deposition of a titanium coating on fatigue behavior of a titanium alloy10.1361/105996306X147108 ↗
10. Influence of plasma and cold spray Ti layers, on high-cycle fatigue properties of Ti6Al4V substrates10.1016/j.surfcoat.2012.11.067 ↗
11. Microstructure and fatigue behavior of cold spray coated Al 505210.1016/j.actamat.2012.08.020 ↗
12. Effect of cold spray deposition of similar material on fatigue behavior of Al 6082 alloy
13. Fatigue behavior of cold spray coatings: the effect of conventional and severe shot peening as pre-/post-treatment10.1016/j.surfcoat.2015.10.063 ↗
14. Effect of substrate roughening and cold spray on fatigue life of AA2024 specimens10.1016/j.matdes.2013.08.061 ↗
15. Mechanical characteristics of Al-Co-Ce coatings produced by the cold spray process10.1007/s11666-007-9099-3 ↗
16. Supersonic particle deposition as a means for enhancing the structural integrity of aircraft structures10.1016/j.ijfatigue.2014.03.013 ↗
17. Nondestructive inspection of fatigue crack propagation beneath supersonic particle deposition coatings during fatigue testing10.1016/j.ijfatigue.2017.05.005 ↗
18. A357.0-T62. [accessed 13 April 2017].
19. Davis JR. Aluminum and aluminum alloys. alloying: understanding the basics, 1st ed. ASM International; 2001. p. 647.10.31399/asm.tb.aub.9781627082976 ↗
20. Blochet Q et al. Influence of spray angle on cold spray with Al for the repair of aircraft components. In: Thermal spray 2014: proceedings of the international thermal spray conference, Barcelona, Spain, May 21–23; 2014.10.31399/asm.cp.itsc2014p0069 ↗
21. Influence of impact angle and gas temperature on mechanical properties of titanium cold spray deposits10.1007/s11666-010-9557-1 ↗
22. Effect of spray angle on deposition characteristics in cold spraying
23. Bonding mechanisms in cold spraying: the contributions of metallurgical and mechanical components10.1007/s11666-009-9298-1 ↗
24. Effect of surface preparation on the microstructure, adhesion, and tensile properties of cold-sprayed aluminum coatings on AA2024 substrates10.1007/s11666-014-0175-1 ↗
25. Moridi A. Cold spray coating; process evaluation and wealth of applications: from structural repair to bioengineering. PhD thesis, Milano; 2015.
26. Petrackova K, Kondas J, Guagliano M. Mechanical performance of cold-sprayed A357 aluminum alloy coatings for repair and additive manufacturing. J Therm Spray Technol 2017;26:1888–97.10.1007/s11666-017-0643-5 ↗
27. Gartner F, Schmidt T, Kreye H. TCT Test, Institute of materials Technology (HSU, Hamburg). [accessed 13 April 2017].
28. ASTM C366 standard test method for adhesion or cohesion strength of thermal spray coatings, C633. West Conshohocken (PA): ASTM International; 2013.
29. ASTM E466-15. Standard practice for conducting force controlled constant amplitude axial fatigue tests of metallic materials. West Conshohocken (PA): ASTM International; 2015. http://doi.org/10.1520/E0466-15.10.1520/E0466-15 ↗
30. Dixon W, Massey F. Introduction to statistical analysis, 3rd ed. McGraw-Hill; 1969. p. 488.