Effect of laser shock peening on high cycle fatigue properties of aluminized AISI 321 stainless steel
Source abstract
Abstract
Abstract In this work, the effect of laser shock peening (LSP) treatment on fatigue property of aluminized AISI 321 stainless steel was studied. The high fraction twinning and compressive residual stress (CRS) induced by LSP at the severe plastic deformation (SPD) layer were found to be responsible for the enhanced fatigue property. De-twinning was conspicuously noticed in LSP sample. Moreover, the dynamic recovery (DRV) was only noticed at SPD layer during cyclic deformation related to CRS. In sum, the aluminized stainless steel achieved an enhanced fatigue property by LSP treatment.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Surface Treatment and Residual Stress · Metal and Thin Film Mechanics · High-Velocity Impact and Material Behavior
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (59)
Show source-provided references
1. Influence of time on the microstructure of AISI 321 austenitic stainless steel in salt bath nitriding10.1016/j.surfcoat.2012.01.063 ↗
2. Effect of δ-ferrite on the stress corrosion cracking behavior of 321 stainless steel10.1016/j.corsci.2019.07.005 ↗
3. Multiple strengthening sources and adiabatic shear banding during high strain-rate deformation of AISI 321 austenitic stainless steel: Effects of grain size and strain rate10.1016/j.msea.2017.11.045 ↗
4. Effect of prior plastic deformation and deformation rate on the corrosion resistance of AISI 321 austenitic stainless steel10.1016/j.msea.2018.12.093 ↗
5. Effect of aluminizing and oxidation on the thermal fatigue damage of hot work tool steels for high pressure die casting applications10.1016/j.ijfatigue.2018.09.018 ↗
6. Corrosion behavior of metastable AISI 321 austenitic stainless steel: Investigating the effect of grain size and prior plastic deformation on its degradation pattern in saline media10.1038/s41598-019-48594-3 ↗
7. Effects of aluminizing and combined strengthening on the fatigue property of K403 superalloy component under combined high and low cycle loading10.1016/j.ijfatigue.2019.04.023 ↗
8. Formation mechanism of multilayer aluminide coating on 316L stainless steel by low-temperature pack cementation10.1016/j.surfcoat.2019.08.005 ↗
9. Low temperature aluminising of Fe-Cr-Ni super alloy by pack cementation10.1016/j.vacuum.2019.01.040 ↗
10. Microstructural investigations on the hot-dip aluminized AISI 321 stainless steel after diffusion treatment10.1016/j.surfcoat.2019.07.031 ↗
11. Effect of Diffusion Process on Coating in Hot-Dipped Aluminized Steel10.1142/S0218625X19500707 ↗
12. Preparation technique and alloying effect of aluminide coatings as tritium permeation barriers: a review10.1016/j.ijhydene.2015.01.052 ↗
13. Formation of aluminide coatings on Fe-based alloys by chemical vapor deposition10.1016/j.surfcoat.2008.01.023 ↗
14. Formation of Al2O3/FeAl coatings on a 9Cr-1Mo steel, and corrosion evaluation in flowing Pb-17Li loop10.1016/j.jnucmat.2017.01.021 ↗
15. Mechanical behavior of coated T91 steel in contact with lead–bismuth liquid alloy at 300° C10.1016/j.surfcoat.2011.03.089 ↗
16. Low-Cycle Fatigue and Fracture Behavior of Aluminized Stainless Steel AISI 321 for Solar Thermal Power Generation Systems10.3390/met10081089 ↗
17. Fatigue life rationalization of laser shock peened SAF 2205 with different swept direction10.1016/j.optlastec.2018.09.017 ↗
18. Residual stress, phase, microstructure and mechanical property studies of ultrafine bainitic steel through laser shock peening10.1016/j.optlastec.2019.02.041 ↗
19. Microstructure and mechanical properties of laser shock peened 38CrSi steel10.1016/j.msea.2020.139486 ↗
20. Compound technology of manufacturing and multiple laser peening on microstructure and fatigue life of dual-phase spring steel10.1016/j.msea.2016.08.031 ↗
21. Influence of hot deformation on dynamic recrystallization behavior of 300M steel: Rules and modeling10.1016/j.msea.2020.139925 ↗
22. Characterization of the hot deformation microstructure of AISI 321 austenitic stainless steel10.1016/j.msea.2018.06.025 ↗
23. Cyclic deformation response of ultra-fine grained titanium at elevated temperatures10.1016/j.ijfatigue.2019.01.021 ↗
24. Internal stress relaxation and load redistribution during the twinning–detwinning-dominated cyclic deformation of a wrought magnesium alloy, ZK60A10.1016/j.actamat.2008.04.006 ↗
25. ASTME466-15 standard.
26. Effect of laser shock strengthening on microstructure and high temperature tensile properties of aluminized steel for solar thermal power generation
27. Evolutions of microstructure, phase, microhardness, and residual stress of multiple laser shock peened Ni-based single crystal superalloy after short-term thermal exposure10.1016/j.optlastec.2019.105917 ↗
28. Residual stress simulation of aluminized layer/ZrO2 composite coating on stainless steel
29. Laser shock processing of aluminium alloys. Application to high cycle fatigue behaviour10.1016/0921-5093(95)10084-9 ↗
30. Thermal evolution of residual stress in IN718 alloy subjected to laser peening10.1016/j.optlaseng.2017.03.004 ↗
31. Grain refinement of LY2 aluminum alloy induced by ultra-high plastic strain during multiple laser shock processing impacts10.1016/j.actamat.2010.03.026 ↗
32. Fatigue behavior of notched steel specimens with nanocrystallized surface obtained by severe shot peening10.1016/j.matdes.2012.09.025 ↗
33. Microstructure and tribological properties of Si-Y/Al two-step deposition coating prepared on Ti2AlNb based alloy by halide activated pack cementation technique
34. Study on the effect mechanism of aluminizing on fatigue performance of K403 nickel-based superalloy10.1016/j.jallcom.2020.155277 ↗
35. Effect of grain size on fatigue behavior of Type 301LN stainless steel10.1016/j.ijfatigue.2013.05.012 ↗
36. Vacancy formation and diffusion in FeAl-alloys[C]//Defect and Diffusion Forum
37. De-twinning via secondary twinning in face-centered cubic alloys10.1016/j.msea.2013.04.075 ↗
38. Gradient plastic strain accommodation and nanotwinning in multi-pass laser shock peened 321 steel10.1016/j.apsusc.2019.05.130 ↗
39. Effect of Laser Shock Processing and Aluminizing on Microstructure and High-Temperature Creep Properties of 321 Stainless Steel for Solar Thermal Power Generation
40. Fatigue and fracture behaviour of austenitic-martensitic high carbon steel under high cycle fatigue: An experimental investigation10.1016/j.msea.2019.02.010 ↗
41. Characterization and analysis on micro-hardness and microstructure evolution of brass subjected to laser shock peening10.1016/j.optlastec.2019.02.043 ↗
42. Twinning and martensite in a 304 austenitic stainless steel10.1016/j.msea.2012.05.080 ↗
43. Study on the effect of multiple laser shock peening on residual stress and microstructural changes in modified 9Cr-1Mo (P91) steel10.1016/j.surfcoat.2018.11.027 ↗
44. Microstructural response and grain refinement mechanism of commercially pure titanium subjected to multiple laser shock peening impacts10.1016/j.actamat.2017.01.050 ↗
45. Laser shock peening induced surface nanocrystallization and martensite transformation in austenitic stainless steel10.1016/j.jallcom.2015.06.268 ↗
46. Deformation-induced martensite and nanotwins by cryogenic laser shock peening of AISI 304 stainless steel and the effects on mechanical properties10.1080/14786435.2011.645899 ↗
47. Structural characterization of aluminized steel heat treated in different environments10.1016/j.surfcoat.2017.12.032 ↗
48. The influence of strain rate on the microstructure transition of 304 stainless steel10.1016/j.actamat.2011.03.005 ↗
49. Tensile property and microstructure of Fe-22Mn-0.5 C TWIP steel10.1016/j.msea.2017.09.061 ↗
50. Localized plastic deformation and hardening in laser shock peened Inconel alloy 718SPF10.1016/j.matchar.2018.05.010 ↗
51. Characterization of ultrasonically peened and laser-shock peened surface layers of AISI 321 stainless steel10.1016/j.surfcoat.2008.04.080 ↗
52. Laser shock peening studies on SS316LN plate with various sacrificial layers10.1016/j.apsusc.2017.11.088 ↗
53. Laser shock processing and its effects on microstructure and properties of metal alloys: a review10.1016/S0142-1123(02)00022-1 ↗
54. Residual stress distribution and microstructure at a laser spot of AISI 304 stainless steel subjected to different laser shock peening impacts10.3390/met6010006 ↗
55. Comparison of the fatigue behavior and residual stress stability of laser-shock peened and deep rolled austenitic stainless steel AISI 304 in the temperature range 25–600 C10.1016/j.msea.2007.02.004 ↗
56. Microstructure, microhardness and residual stress of laser additive manufactured CoCrFeMnNi high-entropy alloy subjected to laser shock peening10.1016/j.jmatprotec.2020.116806 ↗
57. In-situ EBSD study of deformation behaviour of 600 MPa grade dual phase steel during uniaxial tensile tests10.1016/j.msea.2019.05.083 ↗
58. Hot deformation behaviour of Mo-TZM and understanding the restoration processes involved10.1016/j.actamat.2018.10.037 ↗
59. Direct observation of dislocation plasticity in high-Mn lightweight steel by in-situ TEM