Fatigue crack growth in the 2050-T8 aluminium alloy
Source abstract
Abstract
Abstract Fatigue crack growth (FCG) is usually studied using ΔK, however several limitations have been found in the use of da/dN-ΔK curves. Therefore, the FCG in the 2050-T8 aluminium alloy is studied here using the plastic CTOD. Experimental work was developed to obtain FCG in M(T) specimens. The experimental procedure was replicated numerically in terms of geometry, loading and material behaviour. The cyclic plastic behaviour of the material was modeled using stress-strain curves obtained in low-cycle fatigue tests. Numerical predictions of plastic CTOD were obtained for different crack lengths and a da/dN versus plastic CTOD model was built. This model was used to predict the effect of variable amplitude loading, namely, overloads and load blocks. All the predictions agreed qualitatively with the known effect of the load patterns studied. Crack closure was found to be a main mechanism behind the variations of plastic CTOD and therefore of da/dN.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fatigue and fracture mechanics · High Temperature Alloys and Creep · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (49)
Show source-provided references
1. Aluminum-copper-lithium alloy 2050 developed for medium to thick plate10.1007/s11665-009-9554-z ↗
2. Nizery E, Buffiere JY, Proudhon H, Danielou A, Forest S. Influence of particles on short fatigue crack initiation in 2050–T8 and 7050–T74. In: Proc of 14th international conference on aluminium alloys (ICAA14).10.4028/www.scientific.net/MSF.794-796.296 ↗
3. Rice JR. Mechanics of crack tip deformation and extension by fatigue. In: Fatigue crack propagation. Philadelphia: ASTM STP 415; 1967. p. 256–71.10.1520/STP47234S ↗
4. Critical analysis of crack growth propagation laws10.1115/1.3656900 ↗
5. Reconsideration of fatigue crack closure10.1016/0956-716X(92)90164-A ↗
6. An evaluation of DKeff estimation procedure on 6061–T6 and 2024–T3 aluminum alloys10.1016/S0142-1123(99)00055-9 ↗
7. Enhanced model of partial crack closure for correlation of R-ratio effects in aluminum alloys10.1016/S0142-1123(00)00085-2 ↗
8. The influence of T-stress on plasticity induced crack closure under plane strain conditions10.1016/j.ijfatigue.2010.08.002 ↗
9. Influence of non-singular stress terms and specimen geometry on small scale yielding at crack tips in elastic-plastic material10.1016/0022-5096(73)90024-0 ↗
10. Towards a new model of crack tip stress fields10.1007/s10704-008-9209-3 ↗
11. A new (ΔK+Kmax)0.5 driving force parameter for crack growth in aluminum alloys10.1016/S0142-1123(01)00023-8 ↗
12. A two parameter driving force for fatigue crack growth analysis10.1016/j.ijfatigue.2005.07.002 ↗
13. A numerical analysis of CTOD in constant amplitude fatigue crack growth10.1016/j.tafmec.2016.08.015 ↗
14. Antunes FV, Branco R, Prates PA, Borrego L. Fatigue crack growth modelling based on CTOD for the 7050–T6 alloy. Fatigue Fract Eng Mater Struct.
15. Experimental evaluation of CTOD in constant amplitude fatigue crack growth from crack tip displacement fields10.3221/IGF-ESIS.41.22 ↗
16. Numerical modeling of fatigue crack propagation based on the theory of critical distances10.1016/j.engfracmech.2013.10.018 ↗
17. Numerical modeling of fatigue crack propagation based on the Theory of Critical Distances: effects of overloads and underloads10.1016/j.engfracmech.2014.07.006 ↗
18. The relation between crack blunting and fatigue crack growth rates10.1111/j.1460-2695.1994.tb00245.x ↗
19. On fatigue crack growth in ductile materials by crack–tip blunting10.1016/j.jmps.2004.02.007 ↗
20. Fatigue crack closure: from LCF to small scale yielding10.1016/j.ijfatigue.2012.02.016 ↗
21. Microstructure-based fatigue modeling of cast A356–T6 alloy10.1016/S0013-7944(02)00021-8 ↗
22. Modeling fatigue crack growth behavior in rolled AZ31 magnesium alloy using CTOD based strip yield modeling10.1016/j.ijfatigue.2016.11.031 ↗
23. ASTM E647-11: Standard test method for measurement of fatigue crack growth rates. ASTM Annual Book of ASTM Standards, Philadelphia; 2011.
24. Slimani A. Etude par émission acoustique de la déformation cyclique de polycristaux d’aluminium 5N sollicités en traction-compression. Ph.D. thesis, INSA Lyon; 1986.
25. Chicois J. Etude des mécanismes microscopiques de la déformation cyclique. Développement d’une nouvelle approche. Cas de l’aluminium. Ph.D. thesis, INSA Lyon; 1987.
26. ASTM E606. Standard practice for strain-controlled fatigue testing. ASTM International, West Conshohocken, PA; 2004. http://doi.org/10.1520/E0606-04E01.10.1520/E0606-04E01 ↗
27. Inverse strategies for identifying the parameters of constitutive laws of metal sheets10.1155/2016/4152963 ↗
28. Nizery E. Amorçage et propagation des fissures de fatigue dans les alliages d'aluminium 2050–T8 et 7050–T7451. PhD thesis, INSA Lyon; 2015.
29. Mises Rv. Mechanik der festen Körper im plastisch- deformablen Zustand. Nachrichten von der Gesellschaft der Wissenschaften zu Göttingen. Mathematisch-Physikalische Klasse 1913; 1913. p. 582–92.
30. A review of some plasticity and viscoplasticity constitutive theories10.1016/j.ijplas.2008.03.009 ↗
31. Lasdon · 1975
32. A numerical analysis of the mechanisms behind plasticity induced crack closure: application to variable amplitude loadings10.1016/j.ijfatigue.2015.12.006 ↗
33. Three-dimensional numerical simulation of the deep-drawing process using solid finite elements10.1016/S0924-0136(99)00345-3 ↗
34. Algorithms and strategies for treatment of large deformation frictional contact in the numerical simulation of deep drawing process10.1007/s11831-008-9018-x ↗
35. Applying Nagata patches to smooth discretized surfaces used in 3D frictional contact problems10.1016/j.cma.2013.12.008 ↗
36. Study on the influence of work-hardening modeling in springback prediction10.1016/j.ijplas.2006.07.003 ↗
37. On the identification of kinematic hardening with reverse shear test10.1007/s00366-014-0369-7 ↗
38. Influence of the plastic anisotropy modelling in the reverse deep drawing process simulation10.1016/j.matdes.2014.04.008 ↗
39. Evaluation of strain and stress states in the single point incremental forming process10.1007/s00170-015-7954-9 ↗
40. Modeling of tension–compression asymmetry and orthotropy on metallic materials: numerical implementation and validation10.1016/j.ijmecsci.2016.05.020 ↗
41. Anisotropy and plastic flow in the circular bulge test10.1016/j.ijmecsci.2017.04.007 ↗
42. Numerical and experimental analysis of wrinkling during the cup drawing of an AA5042 aluminium alloy10.1007/s12289-015-1265-4 ↗
43. On the accurate assessment of crack opening and closing stresses in plasticity-induced fatigue crack closure problems10.1016/j.engfracmech.2006.09.007 ↗
44. Numerical simulation of plasticity-induced fatigue crack closure with emphasis on the crack growth scheme: 2D and 3D analyses10.1016/j.engfracmech.2007.10.017 ↗
45. In situ SEM testing for crack closure investigation and virtual crack annealing model development10.1016/j.ijfatigue.2012.04.003 ↗
46. A numerical study of the effect of single overloads on plasticity induced10.1016/j.tafmec.2016.12.001 ↗
47. Fatigue crack growth and crack closure in an AlMgSi alloy10.1046/j.1460-2695.2001.00383.x ↗
48. Effect of single overloads in ductile metals: a reconsideration10.1016/j.engfracmech.2006.06.011 ↗
49. Loading history effect on fatigue crack growth of extruded AZ31B magnesium alloy10.1016/j.engfracmech.2013.10.012 ↗