Improving plain and fretting fatigue resistance of A100 steel using ultrasonic nanocrystal surface modification
Source abstract
Abstract
Abstract In this study, ultrasonic nanocrystal surface modification (UNSM) was used to improve plain and fretting fatigue properties of A100 steel. Results showed that an obvious plastic deformation layer was induced in A100 steel, and the martensite microstructure was remarkably refined. In addition, surface compressive residual stress after UNSM treatment was enhanced to 1700 MPa due to the severe lattice distortion. The increased surface hardness and the presence of beneficial compressive residual stresses after UNSM treatment significantly enhanced the plain/fretting fatigue resistance of A100 steel by retarding fatigue crack nucleation and propagation.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Surface Treatment and Residual Stress · Erosion and Abrasive Machining · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. Effect of dilution and macrosegregation on corrosion resistance of laser clad AerMet100 steel coating on 300M steel substrate10.1016/j.surfcoat.2017.04.035 ↗
2. Notch wear prediction model in high speed milling of AerMet100 steel with bull-nose tool considering the influence of stress concentration10.1016/j.wear.2018.05.024 ↗
3. Effect of post-treated low-temperature plasma nitriding on the wear and corrosion resistance of 316L stainless steel manufactured by laser powder-bed fusion
4. Improvement of fatigue properties of Ti-6Al-4V alloy under four-point bending by low temperature nitriding10.1016/j.ijfatigue.2018.11.005 ↗
5. Influence of simultaneous aging and plasma nitriding on fatigue performance of 17–4 PH stainless steel10.1016/j.msea.2017.07.070 ↗
6. Effect of quench-tempering conditions prior to nitriding on microstructure and fretting wear mechanism of gas nitrided X210CrW12 steel10.1016/j.surfcoat.2018.12.066 ↗
7. Effect of gas nitriding on the thermal fatigue behavior of martensitic chromium hot-work tool steel10.1016/j.msea.2015.10.007 ↗
8. Characterization of shot peening properties and modelling on the fatigue performance of 304 austenitic stainless steel10.1016/j.ijfatigue.2020.105621 ↗
9. Martín V, Vázquez J, Navarro C, Domínguez J. Effect of shot peening residual stresses and surface roughness on fretting fatigue strength of Al 7075-T651. Tribology International 2020;142. https://doi.org/10.1016/j.triboint.2019.106004.10.1016/j.triboint.2019.106004 ↗
10. Gradient microstructure and vibration fatigue properties of 2024–T351 aluminium alloy treated by laser shock peening10.1016/j.surfcoat.2020.125698 ↗
11. Effect of laser shock peening on tribological properties of magnesium alloy ZK6010.1016/j.triboint.2019.106138 ↗
12. Effect of surface mechanical attrition treatment on high cycle and very high cycle fatigue of a 7075–T6 aluminium alloy10.1016/j.ijfatigue.2020.105798 ↗
13. Fatigue behaviors of foreign object damaged Ti-6Al-4V alloys under laser shock peening10.1016/j.ijfatigue.2020.105596 ↗
14. Fatigue properties of a S45C steel subjected to ultrasonic nanocrystal surface modification10.1016/j.apsusc.2010.04.007 ↗
15. Improvement of the fatigue strength of SUS304 austenite stainless steel using ultrasonic nanocrystal surface modification10.1016/j.surfcoat.2012.12.033 ↗
16. The effects of ultrasonic nanocrystal surface modification on the fatigue performance of 3D-printed Ti6410.1016/j.ijfatigue.2017.05.019 ↗
17. Effect of ultrasonic nanocrystal surface modification on elevated temperature residual stress, microstructure, and fatigue behavior of ATI 718Plus alloy10.1016/j.ijfatigue.2018.01.017 ↗
18. Fretting wear and friction reduction of CP titanium and Ti-6Al-4V alloy by ultrasonic nanocrystalline surface modification10.1016/j.surfcoat.2012.06.046 ↗
19. Effects of ultrasonic nanocrystal surface modification on the surface integrity, microstructure, and wear resistance of 300M martensitic ultra-high strength steel10.1016/j.jmatprotec.2020.116767 ↗
20. Effect of the ultrasonic surface rolling process on the fretting fatigue behavior of Ti-6Al-4V alloy10.3390/ma10070833 ↗
21. On the effect of pre-strain and pre-fatigue on the monotonic behaviour of ultra-high strength steels10.1016/j.heliyon.2020.e04440 ↗
22. X-ray investigation of stress states in materials
23. The migration of spheroidal cementite towards the surface in nanostructured AISI 52100 steel10.1016/j.matlet.2016.03.096 ↗
24. An improvement in fatigue behavior of AISI 4340 steel by shot peening and ultrasonic nanocrystal surface modification10.1016/j.msea.2020.139752 ↗
25. The influence of ultrasonic surface rolling on the fatigue and wear properties of 23–8N engine valve steel10.1016/j.ijfatigue.2019.04.010 ↗
26. Effects of ultrasonic nanocrystalline surface modification (UNSM) technique on the tribological behavior of sintered Cu-based alloy10.1016/j.triboint.2013.12.003 ↗
27. The effects of ultrasonic nanocrystal surface modification temperature on the mechanical properties and fretting wear resistance of Inconel 690 alloy10.1016/j.apsusc.2018.01.293 ↗
28. Murakami Y. Metal Fatigue: Effects of Small Defects and Nonmetallic Inclusions. Elsevier; 2002. https://doi.org/10.4293/108680811X13125733356710.10.4293/108680811X13125733356710 ↗
29. An evaluation of shot peening, residual stress and stress relaxation on the fatigue life of AISI 4340 steel10.1016/S0142-1123(01)00205-5 ↗
30. Study on fretting wear and tribo-chemical behavior of LZ50 axle steel in torsional fretting fatigue10.1016/j.wear.2018.12.074 ↗
31. Micro-mechanical modelling of fretting fatigue crack initiation and wear in Ti-6Al-4V10.1016/j.ijfatigue.2013.04.019 ↗
32. Fretting fatigue crack nucleation: a review10.1016/j.triboint.2018.01.029 ↗
33. Microstructural fatigue crack growth in single-packet structures of ultra-low carbon steel lath martensite10.1016/j.scriptamat.2019.08.004 ↗
34. Formation of fatigue cracks10.1080/14786435808237004 ↗
35. Prediction of fatigue damage region with the use of the notch critical plane approach for crack initiation and propagation10.1016/j.ijfatigue.2020.105533 ↗
36. A model of metal fatigue10.1038/185303a0 ↗
37. Fatigue damage and crack growth in aluminium alloys10.1016/0001-6160(63)90008-7 ↗
38. A dislocation model for fatigue crack initiation10.1115/1.3157599 ↗
39. Baragetti S, Božić, Arcieri E V. Stress and fracture surface analysis of uncoated and coated 7075-T6 specimens under the rotating bending fatigue loading. Engineering Failure Analysis 2020;112:104512. https://doi.org/10.1016/j.engfailanal.2020.104512.10.1016/j.engfailanal.2020.104512 ↗
40. Study on crack growth and fatigue life in TC6 titanium alloy by integrated phase proportion and grain size modeling10.1016/j.engfracmech.2020.107235 ↗
41. The effects of grain size, dendritic structure and crystallographic orientation on fatigue crack propagation in IN713C nickel-based superalloy10.1016/j.ijplas.2019.09.010 ↗
42. Influence of grain size on the small fatigue crack initiation and propagation behaviors of a nickel-based superalloy at 650℃10.1016/j.jmst.2019.03.023 ↗
43. Fatigue behaviors of AISI 316L stainless steel with a gradient nanostructured surface layer10.1016/j.actamat.2014.12.057 ↗
44. High-cycle fatigue behavior of ultrafine-grained austenitic stainless and TWIP steels10.1016/j.msea.2010.05.035 ↗
45. Effect of surface nanocrystallization on fatigue crack initiation and propagation behavior in pure Zr10.1016/j.msea.2020.139831 ↗
46. Planar slip-driven fatigue crack initiation and propagation in an equiatomic CrMnFeCoNi high-entropy alloy10.1016/j.ijfatigue.2019.105418 ↗
47. Identification of fretting fatigue crack propagation mechanisms using acoustic emission10.1016/j.triboint.2010.06.009 ↗
48. Liu KK, Ã MRH. The effects of laser peening and shot peening on fretting fatigue in Ti–6Al–4V coupons. Tribiology International 2009;42:1250–62. https://doi.org/10.1016/j.triboint.2009.04.005.10.1016/j.triboint.2009.04.005 ↗
49. Effect of fretting on fatigue performance of Ti-1023 titanium alloy10.1016/j.wear.2013.10.010 ↗
50. Fretting fatigue characteristic of Ti–6Al–4V strengthened by wet peening10.1016/j.ijfatigue.2015.12.013 ↗
51. On the effect of shot-peening on fretting fatigue of Al7075-T6 under cyclic normal contact loading10.1016/j.surfcoat.2017.08.067 ↗
52. The fretting fatigue performance of Ti–6Al–4V alloy influenced by microstructure of CuNiIn coating prepared via thermal spraying10.1016/j.triboint.2019.106156 ↗
53. Gradient nanostructure and residual stresses induced by Ultrasonic Nano-crystal Surface Modification in 304 austenitic stainless steel for high strength and high ductility10.1016/j.msea.2014.06.114 ↗
54. Gradient crystalline structure induced by ultrasonic impacting and rolling and its effect on fatigue behavior of TC11 titanium alloy10.1016/j.rinp.2017.05.026 ↗